REAR SPRING EYE BOLTS

Postby Adrian Worman » 21 Nov 2010 16:22

I have to unbolt the rear spring hanger boxes off my car because the main bolts ( which I managed to loosen ok!) are in so that the bolt head is toward the inside of the floorpan and the nut is facing the outer edge of the floorpan. Is this right? Means I have to drop both hangers to remove the spring eye bolts :?
User avatar
Adrian Worman
Frequent Poster
 
Posts: 2051
Joined: 10 Mar 2007 23:54
Location: milton keynes

Postby fal308 » 21 Nov 2010 17:09

When I lifted my dodge Ramcharger I just cut the spring bolts. Some were facing in and some were facing out :shock: Not to mention the right front and left rear were 9/16 while the opposite were 1/2" :roll: Replaced with grade 8 bolts.
fal308
Frequent Poster
 
Posts: 981
Joined: 01 Jan 2004 13:57
Location: Pacific MO

Postby Adrian Worman » 21 Nov 2010 23:49

I pulled the spring hanger boxes out in the end, was the only way I could access the bolts. Can't believe wot a nightmare it turned into either, everything went wrong, cut the side off my finger and carried on working to find blood all over the place, still, next time will be a breeze won't it :?: :lol:
User avatar
Adrian Worman
Frequent Poster
 
Posts: 2051
Joined: 10 Mar 2007 23:54
Location: milton keynes

Postby burdar » 22 Nov 2010 20:30

The nut faced the outside from the factory.

http://www.moparaction.com/Article/PoP/KK.jpg
User avatar
burdar
Frequent Poster
 
Posts: 429
Joined: 24 Mar 2009 17:27
Location: Iowa

Postby dave-r » 22 Nov 2010 21:22

Yeah this all kind of rings a bell in my head now. :roll:

I now seem to remember having to drop the front spring hangers to remove the front eye bolt. But I think I loosened the bolt first because I figured it would be easier to break it free while still attatched to the chassis.

Sorry i didn't remember that before you started mate. :s008:
User avatar
dave-r
Grumpy Old Man
 
Posts: 9842
Joined: 12 Oct 2003 21:45
Location: North of the Tyne, England

Postby dave-r » 22 Nov 2010 21:40

These are my modified offset A-body front spring hangers which i fitted (along with offset rear hangers) to move my springs in by 7/8ths of a inch.

Those are custom (made to my own spec) springs too.

On the back I welded two nuts up where i used to have the spring eye attached in order to give some adjustment.

At some point i decided to mount the spring (on this passenger side only) lower so I drilled a new hole lower and slightly further forward. I can't remember the rational behind that exactly but it was one of my tricks to try and keep the car level on a hard launch but also allow it to sit fairly level at rest.
Anyway. I never did weld that bottom nut in place. It is a bit too deep for the bolt but it has never come loose over the years so it has stayed that way.

042.jpg
043.jpg
User avatar
dave-r
Grumpy Old Man
 
Posts: 9842
Joined: 12 Oct 2003 21:45
Location: North of the Tyne, England

Postby Adrian Worman » 22 Nov 2010 22:31

Thats exactly how it appeared on mine, undid the bolts, came undone ever so easy, and then dropped the hanger boxes.
The ES poly bushes fit well and look like quality pieces, made sure I put plenty of the heavy silicone grease on the outer surfaces and used a Dremel to clean and deburr all the bushing eyes, quite happy with it :wink:
Your custom parts look better manufactured than the factory pieces :!:
User avatar
Adrian Worman
Frequent Poster
 
Posts: 2051
Joined: 10 Mar 2007 23:54
Location: milton keynes

Postby Jon » 24 Nov 2010 4:15

dave-r wrote:Yeah this all kind of rings a bell in my head now. :roll:

I now seem to remember having to drop the front spring hangers to remove the front eye bolt. :s008:


Same here, I once removed the hangers instead of the leaf bolt, it hit the frame if I remember right. Maybe it's a safety feature, like the left hand lug nuts. :?
User avatar
Jon
Frequent Poster
 
Posts: 1229
Joined: 21 Aug 2005 15:12
Location: Medford Oregon