;╔═════════════════════════════════════════════════════════════════╗
;║ ║
;║ HP ISA 16/4 Token-Ring Network Adapter ║
;║ Adapter Configuration File Version 1.20 ║
;║ Copyright (C) 1990 by Hewlett Packard ║
;║ ║
;╚═════════════════════════════════════════════════════════════════╝
BOARD
ID = "OLC0701"
NAME = "HP ISA 16/4 Token-Ring Network Adapter (D2378A)"
MFR = "HP"
CATEGORY = "NET"
SLOT = ISA8OR16
LENGTH = 167
AMPERAGE = 1100
SKIRT = NO
READID = NO
BUSMASTER = 1
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "\nThis is the HP ISA 16/4 dual-speed
(16 Mbps or 4 Mbps) Token Ring Network adapter
card for ISA and EISA bus computers.\n\n
The configuration utility will select a conflict-free
configuration of system resources, and suggest switch
settings for the adapter. These should be viewed on
exit from the utility and set manually on the card
before operation"
SWITCH(1) = 2
NAME = "SW1 RingSpeed switch"
STYPE = SLIDE
VERTICAL = NO
REVERSE = YES
LABEL = LOC(1 2) "16" "4"
FACTORY = LOC(1 2) 01
COMMENTS = "This is the 2-position Ring Speed slide-switch."
SWITCH(2) = 12
NAME = "SW2 Config. switch"
STYPE = DIP
VERTICAL = NO
REVERSE = NO
LABEL = LOC(1-12) "EN" "17" "16" "15" "14" "13"
"I1" "I0" "A1" "A0" "D1" "D0"
FACTORY = LOC(1-12) 111001110011
COMMENTS = "This is the 12-position configuration dip-switch.
Please refer to the Lan Administrator's Manual for an
explanation of switch settings."
FUNCTION = "Token-Ring Network Adapter"
TYPE = "NET,TOK"
CONNECTION = "9-Pin D-Socket: Token Ring Shielded Twisted
Pair (Type 1) Lobe Cable"
SUBFUNCTION = "I/O Address Location"
COMMENTS = "\nUp to four HP Token-Ring Network adapters
may be installed in this computer. An adapter must
use one of four I/O port address combinations.
Each combination consists of two address ranges.\n
Use the VIEW SWITCH & JUMPER SETTINGS function
to display the required switch settings."
CHOICE = "0 = 0A20-0A23 & 0A30-0A3F"
LINK
PORT = 0A20h-0A23h
SHARE = NO
SIZE = BYTE
PORT = 0A30h-0A3Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 00
CHOICE = "1 = 0A24-0A27 & 0A40-0A4F"
LINK
PORT = 0A24h-0A27h
SHARE = NO
SIZE = BYTE
PORT = 0A40h-0A4Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 10
CHOICE = "2 = 0A50-0A53 & 0A60-0A6F"
LINK
PORT = 0A50h-0A53h
SHARE = NO
SIZE = BYTE
PORT = 0A60h-0A6Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 01
CHOICE = "3 = 0A54-0A57 & 0A70-0A7F"
LINK
PORT = 0A54h-0A57h
SHARE = NO
SIZE = BYTE
PORT = 0A70h-0A7Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 11
SUBFUNCTION = "Adapter Data Rate"
TYPE = "SPD"
COMMENTS = "\nThis Token-Ring Network adapter can operate
at two different data rates, 4 Mbps or 16 Mbps.
You MUST set the adapter data rate to the same
rate as the Token-Ring Network LAN segment to
which you are connecting the adapter.\n
Use the VIEW SWITCH & JUMPER SETTINGS function
to display the required switch setting."
CHOICE = "4 Mbps"
SUBTYPE = "4"
FREE
INIT = SWITCH(1) LOC(1 2) 01
CHOICE = "16 Mbps"
SUBTYPE = "16"
FREE
INIT = SWITCH(1) LOC(1 2) 10
SUBFUNCTION = "RPL EPROM Address Location"
COMMENTS = "\nThere are 12 possible 8K blocks of PC memory
for the RPL EPROM area. The Preferred address
location is: CC000-CDFFF.\n
Use the VIEW SWITCH & JUMPER SETTINGS function
to display the required switch settings."
CHOICE = "EPROM Disabled"
LINK
INIT = SWITCH(2) LOC(1-6) 111001
CHOICE = "CC000-CDFFF"
LINK
MEMORY = 8K
ADDRESS = 0CC000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011001
CHOICE = "CE000-CFFFF"
LINK
MEMORY = 8K
ADDRESS = 0CE000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011000
CHOICE = "D0000-D1FFF"
LINK
MEMORY = 8K
ADDRESS = 0D0000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010111
CHOICE = "D2000-D3FFF"
LINK
MEMORY = 8K
ADDRESS = 0D2000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010110
CHOICE = "D4000-D5FFF"
LINK
MEMORY = 8K
ADDRESS = 0D4000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010101
CHOICE = "D6000-D7FFF"
LINK
MEMORY = 8K
ADDRESS = 0D6000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010100
CHOICE = "D8000-D9FFF"
LINK
MEMORY = 8K
ADDRESS = 0D8000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010011
CHOICE = "DA000-DBFFF"
LINK
MEMORY = 8K
ADDRESS = 0DA000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010010
CHOICE = "DC000-DDFFF"
LINK
MEMORY = 8K
ADDRESS = 0DC000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010001
CHOICE = "DE000-DFFFF"
LINK
MEMORY = 8K
ADDRESS = 0DE000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010000
CHOICE = "C8000-C9FFF"
LINK
MEMORY = 8K
ADDRESS = 0C8000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011011
CHOICE = "CA000-CBFFF"
LINK
MEMORY = 8K
ADDRESS = 0CA000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011010
SUBFUNCTION = "Interrupt Level"
TYPE = "INT"
COMMENTS = "\nThis Token-Ring Network adapter can operate
on one of four interrupt levels: 2 (9), 3, 10,
or 11. The preferred interrupt level is 2 (9).\n
NOTE that the adapter only uses edge-triggered
interrupts.\n
Use the VIEW SWITCH & JUMPER SETTINGS function
to display the required switch settings."
CHOICE = "Interrupt 2 (9)"
SUBTYPE = "9"
LINK
IRQ = 9
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 11
CHOICE = "Interrupt 3"
SUBTYPE = "3"
LINK
IRQ = 3
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 10
CHOICE = "Interrupt 10"
SUBTYPE = "10"
LINK
IRQ = 10
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 01
CHOICE = "Interrupt 11"
SUBTYPE = "11"
LINK
IRQ = 11
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 00
SUBFUNCTION = "Data Transfer Mode"
TYPE = "DMA"
COMMENTS = "\nThis Token-Ring Network adapter can operate
on one of three DMA levels: 5, 6 or 7 as a Bus
Master. The preferred DMA level is 5.\n
Use the programmed I/O transfer mode as an
alternative to the Bus Master mode.\n
Use the VIEW SWITCH & JUMPER SETTINGS function
to display the required switch settings."
CHOICE = "Bus master - DMA level 5"
SUBTYPE = "Master5"
LINK
DMA = 5
SHARE = NO
TIMING = DEFAULT
INIT = SWITCH(2) LOC(11 12) 11
CHOICE = "Bus master - DMA level 6"
SUBTYPE = "Master6"
LINK
DMA = 6
SHARE = NO
TIMING = DEFAULT
INIT = SWITCH(2) LOC(11 12) 10
CHOICE = "Bus master - DMA level 7"
SUBTYPE = "Master7"
LINK
DMA = 7
SHARE = NO
TIMING = DEFAULT
INIT = SWITCH(2) LOC(11 12) 01
CHOICE = "Programmed I/O transfer"
SUBTYPE = "PIO"
LINK
INIT = SWITCH(2) LOC(11 12) 00
