BOARD  ;09/10/93 tmt NEW
 ID="ISAB703"
 NAME="Iomega PC1600 SCSI Adapter Board"
 MFR="Iomega Corporation"
 CATEGORY="OTH"
 SLOT=ISA16 
 LENGTH=165
 COMMENTS="The PC1600 is a 16-bit SCSI adapter based on the AIC6260\n
           SCSI chip. Please refer to your users manual for more detail."
 VERSION = 1.0
 HELP="Use the V)iew D)etail by Slot mode to see Configuration Options.
 Use E)dit Change F)unction to select Options.
 Use E)dit Change R)esources to define Options."

JUMPER(5)=8
 NAME="J5"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "DT" "BT" "M0" "M1" "SN" "DN" "R-" "R-"
 FACTORY=LOC(1-8) 00101100
 INITVAL=LOC(7 8) 00 

JUMPER(6)=8
 NAME="J6"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "SD" "SD" "SD" "IC" "IC" "DC" "DC" "SP"
 FACTORY=LOC(1-8) 11101000

; This jumper controls floppy stuff and isn't installed.
;JUMPER(7)=8
; NAME="J7"
; JTYPE=PAIRED
; VERTICAL=NO
; REVERSE=YES
; LABEL=LOC(1-8) "FE" "DR" "DR" "DA" "DA" "16" "10" "DS"
; FACTORY=LOC(1-8) 11010100

JUMPER(8)=8
 NAME="J8"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "DR" "D6" "D5" "D0" "DA" "D6" "D5" "D0"
 FACTORY=LOC(1-8) 00010001
 INITVAL=LOC(1-3) 000 
 INITVAL=LOC(5-7) 000 

JUMPER(9)=8
 NAME="J9"
 JTYPE=PAIRED
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "I2" "I1" "I0" "I9" "AL" "J6" "J4" "BE"
 FACTORY=LOC(1-8) 01000110

SOFTWARE(1)=
 "Configure device drivers with these options:"

FUNCTION="Iomega PC1600 SCSI Adapter Board"
 TYPE="OTH"
 HELP="
 Use E)dit Change F)unction to select Options."
 SUBFUNCTION="Transfer Mode"
   CHOICE="PIO"
     LINK
       INIT = JUMPER(5) LOC(1) 0
       INIT = SOFTWARE(1) "PIO Mode"
       INIT = SOFTWARE(1) "No DMA"
   CHOICE="DMA"
     LINK
       DMA = 0
       INIT = JUMPER(5) LOC(1) 1
       INIT = JUMPER(6) LOC(6 7) 00
       INIT = JUMPER(8) LOC(4 8) 11
       INIT = SOFTWARE(1) "DMA Channel 0"

 SUBFUNCTION="BIOS Enable"
   COMMENTS="BIOS must be enabled to boot from the Iomega PC1600."
   CHOICE="Enabled"
     COMBINE
       INIT = JUMPER(5) LOC(2) 1
       MEMORY=8K
       ADDRESS=0C8000h | 0CC000h | 0D8000h | 0DC000h
       MEMTYPE=OTH
       INIT = JUMPER(9) LOC(6 7 8) 001 | 011 | 101 | 111
       INIT = SOFTWARE(1) "ROM Address C800h" | "ROM Address CC00h" |
               "ROM Address D800h" | "ROM Address DC00h"
   CHOICE="Disabled"
     LINK
       INIT = JUMPER(5) LOC(2) 0
       INIT = JUMPER(9) LOC(8) 0
       INIT = SOFTWARE(1) "BIOS Disabled"

 SUBFUNCTION="Interrupt Request Level"
   CHOICE = "IRQ 10"
     LINK
       IRQ = 10 
       INIT = JUMPER(6) LOC(4 5) 10 
       INIT = JUMPER(9) LOC(1-4) 0010 
       INIT = SOFTWARE(1) "IRQ 10"
   CHOICE = "IRQ 11"
     LINK
       IRQ = 11 
       INIT = JUMPER(6) LOC(4 5) 01 
       INIT = JUMPER(9) LOC(1-4) 0100 
       INIT = SOFTWARE(1) "IRQ 11"
   CHOICE = "IRQ 12"
     LINK
       IRQ = 12 
       INIT = JUMPER(6) LOC(4 5) 11 
       INIT = JUMPER(9) LOC(1-4) 1000 
       INIT = SOFTWARE(1) "IRQ 12"
   CHOICE = "IRQ 9"
     LINK
       IRQ = 9 
       INIT = JUMPER(6) LOC(4 5) 00 
       INIT = JUMPER(9) LOC(1-4) 0001 
       INIT = SOFTWARE(1) "IRQ 9"

 SUBFUNCTION="I/O Port Address"
   CHOICE="340H-35EH"
     LINK
       PORT = 340H-35EH
       INIT = JUMPER(9) LOC(5) 0
       INIT = SOFTWARE(1) "I/O Address 340-35Eh"
   CHOICE="140H-15EH"
     LINK
       PORT = 140H-15EH
       INIT = JUMPER(9) LOC(5) 1
       INIT = SOFTWARE(1) "I/O Address 140-15Eh"

 SUBFUNCTION="Initiator SCSI ID"
   CHOICE="SCSI ID 7"
     LINK
       INIT = JUMPER(6) LOC(1-3) 111
       INIT = SOFTWARE(1) "SCSI ID 7"
   CHOICE="SCSI ID 6"
     LINK
       INIT = JUMPER(6) LOC(1-3) 011
       INIT = SOFTWARE(1) "SCSI ID 6"
   CHOICE="SCSI ID 5"
     LINK
       INIT = JUMPER(6) LOC(1-3) 101
       INIT = SOFTWARE(1) "SCSI ID 5"
   CHOICE="SCSI ID 4"
     LINK
       INIT = JUMPER(6) LOC(1-3) 001
       INIT = SOFTWARE(1) "SCSI ID 4"
   CHOICE="SCSI ID 3"
     LINK
       INIT = JUMPER(6) LOC(1-3) 110
       INIT = SOFTWARE(1) "SCSI ID 3"
   CHOICE="SCSI ID 2"
     LINK
       INIT = JUMPER(6) LOC(1-3) 010
       INIT = SOFTWARE(1) "SCSI ID 2"
   CHOICE="SCSI ID 1"
     LINK
       INIT = JUMPER(6) LOC(1-3) 100
       INIT = SOFTWARE(1) "SCSI ID 1"
   CHOICE="SCSI ID 0"
     LINK
       INIT = JUMPER(6) LOC(1-3) 000
       INIT = SOFTWARE(1) "SCSI ID 0"

 SUBFUNCTION="SCSI Synch. Xfers"
   CHOICE="Enable"
     LINK
       INIT = JUMPER(5) LOC(5) 1
       INIT = SOFTWARE(1) "Synch. Xfers Enabled"
   CHOICE="Disable"
     LINK
       INIT = JUMPER(5) LOC(5) 0
       INIT = SOFTWARE(1) "Synch. Xfers Disabled"

 SUBFUNCTION="SCSI Disconnect"
   CHOICE="Allow"
     LINK
       INIT = JUMPER(5) LOC(6) 1
       INIT = SOFTWARE(1) "Disconnect Allowed"
   CHOICE="Disallow"
     LINK
       INIT = JUMPER(5) LOC(6) 0
       INIT = SOFTWARE(1) "Disconnect Disallowed"