;╔═════════════════════════════════════════════════════════════════╗
;║ ║
;║ Intel TokenExpress(tm) ISA/16s Network Adapter ║
;║ (Switchless) ║
;║ Adapter Configuration File Version 1.0 ║
;║ (C) Copyright 1992, Intel Corp. ║
;║ ║
;╚═════════════════════════════════════════════════════════════════╝
BOARD
ID = "INT0703"
NAME = "Intel TokenExpress(tm) ISA/16s Network Adapter"
MFR = "Intel"
CATEGORY = "NET"
SLOT = ISA8OR16
LENGTH = 160
AMPERAGE = 700
SKIRT = NO
READID = NO
BUSMASTER = 1
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "\nThis is the Intel TokenExpress(tm) ISA/16s adapter,
a high performance Token-Ring adapter for ISA and EISA
bus computers. This adapter can operate on networks
having a ring speed of either 4 Mbps or 16 Mbps.\n\n
This configuration program will note which setup parameters
are already in use by other devices in this computer and
suggest a configuration based on the available options.
Write down the recommended options, exit this program,
and run Intel's TOKENSET program to manually configure
your adapter."
FUNCTION = "Token-Ring Network Adapter"
TYPE = "NET,TOK"
CONNECTION = "8-Pin RJ45 and 9-Pin D-connector"
SUBFUNCTION = "I/O Address"
COMMENTS = "\nA maximum of four Intel TokenExpress network adapters
may be installed in this computer. Each adapter must
use one of the four I/O port address combinations.
(Each combination consists of two address ranges). Use
Intel's TOKENSET program to set your desired I/O address."
CHOICE = "0 = 0A20-0A23 & 0A30-0A3F"
LINK
PORT = 0A20h-0A23h
SHARE = NO
SIZE = BYTE
LINK
PORT = 0A30h-0A3Fh
SHARE = NO
SIZE = BYTE
CHOICE = "1 = 0A24-0A27 & 0A40-0A4F"
LINK
PORT = 0A24h-0A27h
SHARE = NO
SIZE = BYTE
LINK
PORT = 0A40h-0A4Fh
SHARE = NO
SIZE = BYTE
CHOICE = "2 = 0A50-0A53 & 0A60-0A6F"
LINK
PORT = 0A50h-0A53h
SHARE = NO
SIZE = BYTE
LINK
PORT = 0A60h-0A6Fh
SHARE = NO
SIZE = BYTE
CHOICE = "3 = 0A54-0A57 & 0A70-0A7F"
LINK
PORT = 0A54h-0A57h
SHARE = NO
SIZE = BYTE
LINK
PORT = 0A70h-0A7Fh
SHARE = NO
SIZE = BYTE
SUBFUNCTION = "RPL PROM Address Location"
COMMENTS = "\nThere are 16 possible 8K blocks of PC memory
for the RPL PROM area. The recommended address
location is CC000-CDFFF. Use Intel's TOKENSET
program to set your desired RPL PROM Address location."
CHOICE = "RPL PROM Disabled"
CHOICE = "CC000-CDFFF"
LINK
MEMORY = 8K
ADDRESS = 0CC000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "CE000-CFFFF"
LINK
MEMORY = 8K
ADDRESS = 0CF000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "D0000-D1FFF"
LINK
MEMORY = 8K
ADDRESS = 0D0000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "D2000-D3FFF"
LINK
MEMORY = 8K
ADDRESS = 0D2000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "D4000-D5FFF"
LINK
MEMORY = 8K
ADDRESS = 0D4000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "D6000-D7FFF"
LINK
MEMORY = 8K
ADDRESS = 0D6000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "D8000-D9FFF"
LINK
MEMORY = 8K
ADDRESS = 0D8000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "DA000-DBFFF"
LINK
MEMORY = 8K
ADDRESS = 0DA000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "DC000-DDFFF"
LINK
MEMORY = 8K
ADDRESS = 0DC000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "DE000-DFFFF"
LINK
MEMORY = 8K
ADDRESS = 0DE000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "C0000-C1FFF"
LINK
MEMORY = 8K
ADDRESS = 0C0000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "C2000-C3FFF"
LINK
MEMORY = 8K
ADDRESS = 0C2000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "C4000-C5FFF"
LINK
MEMORY = 8K
ADDRESS = 0C4000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "C6000-C7FFF"
LINK
MEMORY = 8K
ADDRESS = 0C6000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "C8000-C9FFF"
LINK
MEMORY = 8K
ADDRESS = 0C8000h
WRITABLE = NO
SIZE = BYTE
CHOICE = "CA000-CBFFF"
LINK
MEMORY = 8K
ADDRESS = 0CA000h
WRITABLE = NO
SIZE = BYTE
SUBFUNCTION = "Interrupt Level"
TYPE = "INT"
COMMENTS = "\nThis TokenExpress adapter can be set to any
one of eight different interrupt levels: 2 (9),
3, 5, 7, 10, 11, 12 or 15. The recommended
interrupt level is 2 (9). Please note that the
adapter only uses edge-triggered interrupts. Use
Intel's TOKENSET program to set the desired
interrupt level."
CHOICE = "Interrupt 2 (9)"
SUBTYPE = "9"
LINK
IRQ = 9
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 3"
SUBTYPE = "3"
LINK
IRQ = 3
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 5"
SUBTYPE = "5"
LINK
IRQ = 5
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 7"
SUBTYPE = "7"
LINK
IRQ = 7
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 10"
SUBTYPE = "10"
LINK
IRQ = 10
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 11"
SUBTYPE = "11"
LINK
IRQ = 11
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 12"
SUBTYPE = "12"
LINK
IRQ = 12
SHARE = NO
TRIGGER = EDGE
CHOICE = "Interrupt 15"
SUBTYPE = "15"
LINK
IRQ = 15
SHARE = NO
TRIGGER = EDGE
SUBFUNCTION = "Data Transfer Mode"
TYPE = "DMA"
COMMENTS = "\nThis TokenExpress adapter can utilize any of
one of six DMA channels (0, 1, 3, 5, 6 or 7) when
operating as a Bus Master. The recommended DMA
channel is 5. The programmed I/O transfer mode can
be used as an alternative to the Bus Master mode. Use
Intel's TOKENSET program to set your desired
DMA channel."
CHOICE = "Bus master - DMA level 5"
SUBTYPE = "Master5"
LINK
DMA = 5
SHARE = NO
TIMING = DEFAULT
CHOICE = "Bus master - DMA level 6"
SUBTYPE = "Master6"
LINK
DMA = 6
SHARE = NO
TIMING = DEFAULT
CHOICE = "Bus master - DMA level 7"
SUBTYPE = "Master7"
LINK
DMA = 7
SHARE = NO
TIMING = DEFAULT
CHOICE = "Bus master - DMA level 0"
SUBTYPE = "Master0"
LINK
DMA = 0
SHARE = NO
TIMING = DEFAULT
CHOICE = "Bus master - DMA level 1"
SUBTYPE = "Master1"
LINK
DMA = 1
SHARE = NO
TIMING = DEFAULT
CHOICE = "Bus master - DMA level 3"
SUBTYPE = "Master3"
LINK
DMA = 3
SHARE = NO
TIMING = DEFAULT
CHOICE = "Programmed I/O transfer"
SUBTYPE = "PIO"
