;╔═════════════════════════════════════════════════════════════════╗
;║ ║
;║ Intel TokenExpress(tm) ISA 16/4 Network Adapter ║
;║ Adapter Configuration File Version 1.30 ║
;║ Copyright (C) 1992, Intel Corp. ║
;║ ║
;╚═════════════════════════════════════════════════════════════════╝
BOARD
ID = "INT0701"
NAME = "Intel TokenExpress(tm) ISA 16/4 Network Adapter"
MFR = "Intel"
CATEGORY = "NET"
SLOT = ISA8OR16
LENGTH = 167
AMPERAGE = 1100
SKIRT = NO
READID = NO
BUSMASTER = 1
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "\nThis is the Intel TokenExpress(tm) 16/4 ISA
adapter, a high performance Token-Ring adapter for
ISA and EISA bus computers. This adapter can operate
on networks having a ring speed of either 4 Mbps or
16 Mbps.\n\n
This configuration program will note which switch settings
are already in use by other devices in this computer and
suggest a configuration for the TokenExpress adapter based
on the available options. Be sure to use these settings
when manually configuring your adapter."
SWITCH(1) = 2
NAME = "SW1 Ring Speed switch"
STYPE = SLIDE
VERTICAL = NO
REVERSE = YES
LABEL = LOC(1 2) "16" "4"
FACTORY = LOC(1 2) 01
COMMENTS = "This is the 2-position Ring Speed switch."
SWITCH(2) = 12
NAME = "SW2 Config. switch"
STYPE = DIP
VERTICAL = NO
REVERSE = NO
LABEL = LOC(1-12) "EN" "17" "16" "15" "14" "13"
"I1" "I0" "A1" "A0" "D1" "D0"
FACTORY = LOC(1-12) 111001110011
COMMENTS = "This is the 12-position configuration dip-switch.
Please refer to your Intel TokenExpress installation
guide for an explanation of the switch settings."
FUNCTION = "Token-Ring Network Adapter"
TYPE = "NET,TOK"
CONNECTION = "9-Pin D-Socket: Token-Ring Shielded Twisted
Pair (Type 1) Lobe Cable"
SUBFUNCTION = "I/O Address Location"
COMMENTS = "\nA maximum of four Intel TokenExpress adapters
may be installed in this computer. Each adapter must
use one of the four I/O port address combinations.
(Each combination consists of two address ranges).\n\n
Use this program's switch viewing function
to display the required switch settings."
CHOICE = "0 = 0A20-0A23 & 0A30-0A3F"
FREE
PORT = 0A20h-0A23h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A30h-0A3Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 00
INIT = PORTADR(0A38h) 11111111
INIT = PORTADR(0A38h) 00101110
CHOICE = "1 = 0A24-0A27 & 0A40-0A4F"
FREE
PORT = 0A24h-0A27h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A40h-0A4Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 10
INIT = PORTADR(0A48h) 11111111
INIT = PORTADR(0A48h) 00101110
CHOICE = "2 = 0A50-0A53 & 0A60-0A6F"
FREE
PORT = 0A50h-0A53h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A60h-0A6Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 01
INIT = PORTADR(0A68h) 11111111
INIT = PORTADR(0A68h) 00101110
CHOICE = "3 = 0A54-0A57 & 0A70-0A7F"
FREE
PORT = 0A54h-0A57h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A70h-0A7Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(9 10) 11
INIT = PORTADR(0A78h) 11111111
INIT = PORTADR(0A78h) 00101110
SUBFUNCTION = "Ring Speed"
TYPE = "SPD"
COMMENTS = "\nThis TokenExpress adapter can operate
at two different ring speeds, 4 Mbps or 16 Mbps.
You MUST set the adapter's ring speed to match
the speed of the network to which it is connected.\n\n
Use this program's switch viewing function
to display the required switch settings."
CHOICE = "4 Mbps"
SUBTYPE = "4"
FREE
INIT = SWITCH(1) LOC(1 2) 01
CHOICE = "16 Mbps"
SUBTYPE = "16"
FREE
INIT = SWITCH(1) LOC(1 2) 10
SUBFUNCTION = "RPL PROM Address Location"
COMMENTS = "\nThere are 12 possible 8K blocks of PC memory
that can be assigned for the RPL PROM area.
The recommended address location is CC000-CDFFF.\n\n
Use this program's switch viewing function
to display the required switch settings."
CHOICE = "RPL PROM Disabled"
LINK
INIT = SWITCH(2) LOC(1-6) 111001
CHOICE = "CC000-CDFFF"
LINK
MEMORY = 8K
ADDRESS = 0CC000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011001
CHOICE = "CE000-CFFFF"
LINK
MEMORY = 8K
ADDRESS = 0CE000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011000
CHOICE = "D0000-D1FFF"
LINK
MEMORY = 8K
ADDRESS = 0D0000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010111
CHOICE = "D2000-D3FFF"
LINK
MEMORY = 8K
ADDRESS = 0D2000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010110
CHOICE = "D4000-D5FFF"
LINK
MEMORY = 8K
ADDRESS = 0D4000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010101
CHOICE = "D6000-D7FFF"
LINK
MEMORY = 8K
ADDRESS = 0D6000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010100
CHOICE = "D8000-D9FFF"
LINK
MEMORY = 8K
ADDRESS = 0D8000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010011
CHOICE = "DA000-DBFFF"
LINK
MEMORY = 8K
ADDRESS = 0DA000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010010
CHOICE = "DC000-DDFFF"
LINK
MEMORY = 8K
ADDRESS = 0DC000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010001
CHOICE = "DE000-DFFFF"
LINK
MEMORY = 8K
ADDRESS = 0DE000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 010000
CHOICE = "C8000-C9FFF"
LINK
MEMORY = 8K
ADDRESS = 0C8000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011011
CHOICE = "CA000-CBFFF"
LINK
MEMORY = 8K
ADDRESS = 0CA000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(2) LOC(1-6) 011010
SUBFUNCTION = "Interrupt Level"
TYPE = "INT"
COMMENTS = "\nThis TokenExpress adapter can be set to any
of four interrupt levels: 2 (9), 3, 10, or 11.
The recommended interrupt level is 2 (9).\n
Please note that the adapter only uses edge-triggered
interrupts.\n\n
Use this program's switch viewing function
to display the required switch settings."
CHOICE = "Interrupt 2 (9)"
SUBTYPE = "9"
LINK
IRQ = 9
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 11
CHOICE = "Interrupt 3"
SUBTYPE = "3"
LINK
IRQ = 3
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 10
CHOICE = "Interrupt 10"
SUBTYPE = "10"
LINK
IRQ = 10
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 01
CHOICE = "Interrupt 11"
SUBTYPE = "11"
LINK
IRQ = 11
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(2) LOC(7 8) 00
SUBFUNCTION = "Data Transfer Mode"
TYPE = "DMA"
COMMENTS = "\nThis TokenExpress adapter can utilize any of
the three available DMA channels: 5, 6 or 7 as a Bus
Master. The recommended DMA channel is 5.\n
The programmed I/O transfer mode can be used as an
alternative to the Bus Master mode.\n
Use this program's switch viewing function
to display the required switch settings."
CHOICE = "Bus master - DMA level 5"
SUBTYPE = "Master5"
LINK
DMA = 5
SHARE = NO
TIMING = DEFAULT
INIT = SWITCH(2) LOC(11 12) 11
CHOICE = "Bus master - DMA level 6"
SUBTYPE = "Master6"
LINK
DMA = 6
SHARE = NO
TIMING = DEFAULT
INIT = SWITCH(2) LOC(11 12) 10
CHOICE = "Bus master - DMA level 7"
SUBTYPE = "Master7"
LINK
DMA = 7
SHARE = NO
TIMING = DEFAULT
INIT = SWITCH(2) LOC(11 12) 01
CHOICE = "Programmed I/O transfer"
SUBTYPE = "PIO"
LINK
INIT = SWITCH(2) LOC(11 12) 00
