;╔═════════════════════════════════════════════════════════════════╗
;║ ║
;║ Intel TokenExpress(tm) ISA/8 Network Adapter ║
;║ Adapter Configuration File Version 1.10 ║
;║ Copyright (C) 1992, Intel Corp. ║
;║ ║
;╚═════════════════════════════════════════════════════════════════╝
BOARD
ID = "IIN0B01"
NAME = "Intel TokenExpress(tm) ISA/8 Network Adapter"
MFR = "Intel"
CATEGORY = "NET"
SLOT = ISA8
LENGTH = 109
AMPERAGE = 800
SKIRT = NO
READID = NO
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "\nThis is the Intel TokenExpress(tm) ISA/8 Token-Ring
adapter for ISA and EISA bus computers. This adapter
operates on networks having a ring speed of either
4 Mbps or 16 Mbps.\n\n
This configuration program will note which switch settings
are already in use by other devices in this computer and
suggest a configuration for the TokenExpress adapter based
on the available options. Be sure to use these settings
when manually configuring your adapter."
SWITCH(1) = 8
NAME = "SW1 Config. switch"
STYPE = DIP
VERTICAL = NO
REVERSE = YES
LABEL = LOC(1-8) "SP" "A0" "A1" "I0" "11" "14"
"15" "16"
FACTORY = LOC(1-8) 00000000
COMMENTS = "This is the 8-position configuration dip-switch.
Please refer to your Intel TokenExpress installation
guide for an explanation of the switch settings."
FUNCTION = "Token-Ring Network Adapter"
TYPE = "NET,TOK"
CONNECTION = "9-Pin D-Socket for Token Ring Shielded Twisted
Pair Lobe Cable or 8-pin Phone-connector for
Unshielded Twisted Pair Lobe Cable"
SUBFUNCTION = "I/O Address Location"
COMMENTS = "\nA maximum of four Intel TokenExpress adapters
may be installed in this computer. Each adapter must
use one of the four I/O port address combinations.
(Each combination consists of two address ranges).\n\n
Use this program's switch viewing function to display
the required switch settings."
CHOICE = "0 = 0A20 & 0A22-0A23 & 0A30-0A3F"
FREE
PORT = 0A20h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A22h-0A23h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A30h-0A3Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(2 3) 00
INIT = PORTADR(0A38h) 11111111
INIT = PORTADR(0A38h) 00101110
CHOICE = "1 = 0A24 & 0A26-0A27 & 0A40-0A4F"
FREE
PORT = 0A24h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A26h-0A27h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A40h-0A4Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(2 3) 01
INIT = PORTADR(0A48h) 11111111
INIT = PORTADR(0A48h) 00101110
CHOICE = "2 = 0A50 & 0A52-0A53 & 0A60-0A6F"
FREE
PORT = 0A50h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A52h-0A53h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A60h-0A6Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(2 3) 10
INIT = PORTADR(0A68h) 11111111
INIT = PORTADR(0A68h) 00101110
CHOICE = "3 = 0A54 & 0A55-0A57 & 0A70-0A7F"
FREE
PORT = 0A54h
SHARE = NO
FREE
PORT = 0A56h-0A57h
SHARE = NO
SIZE = BYTE
FREE
PORT = 0A70h-0A7Fh
SHARE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(2 3) 11
INIT = PORTADR(0A78h) 11111111
INIT = PORTADR(0A78h) 00101110
SUBFUNCTION = "Ring Speed"
TYPE = "SP"
COMMENTS = "\nThis TokenExpress adapter can operate
at two different ring speeds, 4 Mbps or 16 Mbps.
You MUST set the adapter's ring speed to match
the speed of the network to which it is connected.\n\n
Use this program's switch viewing function to display
the required switch settings."
CHOICE = "4 Mbps"
SUBTYPE = "4"
FREE
INIT = SWITCH(1) LOC(1) 0
CHOICE = "16 Mbps"
SUBTYPE = "16"
FREE
INIT = SWITCH(1) LOC(1) 1
SUBFUNCTION = "RPL PROM Address Location"
COMMENTS = "\nThere are 7 possible 8K blocks of PC memory
that can be assigned for the RPL PROM area.
The recommended address location is CE000-CFFFF.\n
Use this program's switch viewing function to display
the required switch settings."
CHOICE = "RPL PROM Disabled"
LINK
INIT = SWITCH(1) LOC(6-8) 000
CHOICE = "C6000-C7FFF"
LINK
MEMORY = 8K
ADDRESS = 0C6000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 100
CHOICE = "CA000-CBFFF"
LINK
MEMORY = 8K
ADDRESS = 0CA000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 010
CHOICE = "CE000-CFFFF"
LINK
MEMORY = 8K
ADDRESS = 0CE000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 110
CHOICE = "D2000-D3FFF"
LINK
MEMORY = 8K
ADDRESS = 0D2000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 001
CHOICE = "D6000-D7FFF"
LINK
MEMORY = 8K
ADDRESS = 0D6000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 101
CHOICE = "DA000-DBFFF"
LINK
MEMORY = 8K
ADDRESS = 0DA000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 011
CHOICE = "DE000-DFFFF"
LINK
MEMORY = 8K
ADDRESS = 0DE000h
WRITABLE = NO
SIZE = BYTE
INIT = SWITCH(1) LOC(6-8) 111
SUBFUNCTION = "Interrupt Level"
TYPE = "INT"
COMMENTS = "\nThis TokenExpress adapter can be set to any
of four interrupt levels: 2 (9), 3, 5, or 7.
The recommended interrupt level is 2 (9).\n
Please note that this adapter only uses edge-triggered
interrupts.\n
Use this program's switch viewing function to display
the required switch settings."
CHOICE = "Interrupt 2 (9)"
SUBTYPE = "9"
LINK
IRQ = 9
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(1) LOC(4 5) 00
CHOICE = "Interrupt 3"
SUBTYPE = "3"
LINK
IRQ = 3
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(1) LOC(4 5) 10
CHOICE = "Interrupt 5"
SUBTYPE = "5"
LINK
IRQ = 5
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(1) LOC(4 5) 01
CHOICE = "Interrupt 7"
SUBTYPE = "7"
LINK
IRQ = 7
SHARE = NO
TRIGGER = EDGE
INIT = SWITCH(1) LOC(4 5) 11
