BOARD
     ID = "ICU00B0"
     NAME = "3COM Etherlink II (3C503) Network Adapter"
     MFR = "3COM"
     CATEGORY = "NET"
     SLOT = ISA8
     COMMENTS = "3COM Etherlink II (3C503) Network Adapter"
     VERSION = 2.0

JUMPER(1) = 5
     NAME = "J1-Memory"
     JTYPE = PAIRED
     VERTICAL = YES
     REVERSE = NO
     LABEL = LOC(5-1) "DISABLE"
                      "DC000"
                      "D8000"
                      "CC000"
                      "C8000"
     FACTORY = LOC(5-1) 10000

JUMPER(2) = 8
     NAME = "J2-I/O"
     JTYPE = PAIRED
     VERTICAL = YES
     REVERSE = NO
     LABEL = LOC(8-1) "300"
                      "310"
                      "330"
                      "350"
                      "250"
                      "280"
                      "2A0"
                      "2E0"
     FACTORY = LOC(8-1) 10000000

SOFTWARE(1) = "Interrupt, DMA Channel, and Ethernet type are set as parameters to
               ETH503.SYS.  This device driver is started in CONFIG.SYS.
               Set the parameters as follows:
               \n\n DEVICE=ETH503.SYS /i:int /a:addr /d:dma /t:eth
               \n  where...
               \n    int=interrupt
               \n    addr=I/O address(must match jumper setting)
               \n    dma=DMA Channel
               \n    eth=Ethernet type (1=thin,2=thick)"

FUNCTION = "Etherlink II  Adapter Resources"
TYPE = "NET"
SUBFUNCTION = "Interrupt"
     CHOICE = "IRQ3"
       FREE
       IRQ = 3
       INIT = SOFTWARE(1) "int = 3"
     CHOICE = "IRQ2"
       FREE
       IRQ = 2
       INIT = SOFTWARE(1) "int = 2"
     CHOICE = "IRQ4"
       FREE
       IRQ = 4
       INIT = SOFTWARE(1) "int = 4"
     CHOICE = "IRQ5"
       FREE
       IRQ = 5
       INIT = SOFTWARE(1) "int = 5"

SUBFUNCTION = "Memory Address for PROM or Shared Memory"
     CHOICE = "Disabled"
       DISABLE = YES
       FREE
       INIT = JUMPER(1) LOC(5-1) 10000
     CHOICE = "DC000H"
       FREE
       MEMORY = 8K
       ADDRESS = 0DC000H
       WRITABLE = YES
       SHARE = NO
       MEMTYPE = OTH
       INIT = JUMPER(1) LOC(5-1) 01000
     CHOICE = "D8000H"
       FREE
       MEMORY = 8K
       ADDRESS = 0D8000H
       WRITABLE = YES
       SHARE = NO
       MEMTYPE = OTH
       INIT = JUMPER(1) LOC(5-1) 00100
     CHOICE = "CC000H"
       FREE
       MEMORY = 8K
       ADDRESS = 0CC000H
       WRITABLE = YES
       SHARE = NO
       MEMTYPE = OTH
       INIT = JUMPER(1) LOC(5-1) 00010
     CHOICE = "C8000H"
       FREE
       MEMORY = 8K
       ADDRESS = 0C8000H
       WRITABLE = YES
       SHARE = NO
       MEMTYPE = OTH
       INIT = JUMPER(1) LOC(5-1) 00001

SUBFUNCTION = "I/O Address"
     CHOICE = "300H"
       FREE
       PORT = 300H-30FH
       INIT = JUMPER(2) LOC(8-1) 10000000
       INIT = SOFTWARE(1) "addr=300"
     CHOICE = "310H"
       FREE
       PORT = 310H-31FH
       INIT = JUMPER(2) LOC(8-1) 01000000
       INIT = SOFTWARE(1) "addr=310"
     CHOICE = "330H"
       FREE
       PORT = 330H-33FH
       INIT = JUMPER(2) LOC(8-1) 00100000
       INIT = SOFTWARE(1) "addr=330"
     CHOICE = "350H"
       FREE
       PORT = 350H-35FH
       INIT = JUMPER(2) LOC(8-1) 00010000
       INIT = SOFTWARE(1) "addr=350"
     CHOICE = "250H"
       FREE
       PORT = 250H-25FH
       INIT = JUMPER(2) LOC(8-1) 00001000
       INIT = SOFTWARE(1) "addr=250"
     CHOICE = "280H"
       FREE
       PORT = 280H-28FH
       INIT = JUMPER(2) LOC(8-1) 00000100
       INIT = SOFTWARE(1) "addr=280"
     CHOICE = "2A0H"
       FREE
       PORT = 2A0H-2AFH
       INIT = JUMPER(2) LOC(8-1) 00000010
       INIT = SOFTWARE(1) "addr=2A0"
     CHOICE = "2E0H"
       FREE
       PORT = 2E0H-2EFH
       INIT = JUMPER(2) LOC(8-1) 00000001
       INIT = SOFTWARE(1) "addr=2E0"

SUBFUNCTION = "DMA Channel"
     CHOICE = "DMA 1"
       FREE
       DMA = 1
       INIT = SOFTWARE(1) "dma=1"
     CHOICE = "DMA 2"
       FREE
       DMA = 2
       INIT = SOFTWARE(1) "dma=2"
     CHOICE = "DMA 3"
       FREE
       DMA = 3
       INIT = SOFTWARE(1) "dma=3"

SUBFUNCTION = "Ethernet Type"
     CHOICE = "Thin"
       FREE
       INIT = SOFTWARE(1) "eth=1"
     CHOICE = "Thick"
       FREE
       INIT = SOFTWARE(1) "eth=0"