;
; (C)Copyright Distributed Processing Technology, 1989-1992
; All Rights Reserved.
;
; DPT PM2011B1/90 ISA to SCSI Host Bus Adapter Configuration File
;
; Date = 7/13/92
; Version = (See version at end of this file.)
; Filename = !DPTA701.CFG
;
BOARD
ID = "DPTA701"
NAME = "DPT SCSI Host Bus Adapter (PM2011B1/9X)"
MFR = "DPT"
CATEGORY = "MSD"
SLOT = ISA16
LENGTH = 341
SKIRT = NO
READID = NO
BUSMASTER = 999
AMPERAGE = 2300
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "\nThe Distributed Processing Technology PM2011B1/9X is a high
performance SCSI Host Bus Adapter with an ISA host interface.\n
Key features of the adapter are:\n\n
\t* Up to 16MB of disk cache\n
\t* 5MB/sec ISA transfer\n
\t* ISA bus mastering\n
\t* SCSI-2 compliant\n
\t* 10MB/sec SCSI sync transfer\n
\t* WD1003 hardware emulation\n
\t* CAM-compliant EATA interface\n
\t* Overlapped commands\n
\t* Scatter/gather\n
\t* Automatic request sense\n
\t* RAID Support\n\n
For additional information, contact:\n\n
\tDPT Customer Support\n
\t(407) 830-5522"
IOPORT(1) =0zC90h
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
JUMPER(1) = 1
NAME = "Floppy Disable"
JTYPE = PAIRED
LABEL = LOC(1) "Y20"
FACTORY = LOC(1) 0
VERTICAL = NO
REVERSE = YES
COMMENTS = "Install jumper to Disable floppy controller on card."
HELP = "The Floppy Disable jumper is shipped from the factory removed,
allowing floppy access via the DPT controller."
JUMPER(2) = 1
NAME = "Floppy Address"
JTYPE = PAIRED
LABEL = LOC(1) "Y34"
FACTORY = LOC(1) 0
VERTICAL = NO
REVERSE = YES
COMMENTS = "Jumper these pins to move floppy address to 370h"
HELP = "Do not jumper these pins unless you need the floppy to use
an alternate address."
JUMPER(3) = 2
NAME = "Option ROM Address"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y36" "Y37"
FACTORY = LOC(1 2) 11
VERTICAL = NO
REVERSE = YES
COMMENTS = "These jumpers are used to select Optional ROM address or
disable it"
HELP = "The address of the Option ROM may be changed if it conflicts
with another card. If there are multiple DPT controllers in
your system, only one should have SmartRom Enabled."
JUMPER(4) = 1
NAME = "Drive SA and LA17-19"
JTYPE = PAIRED
LABEL = LOC(1) "Y19"
FACTORY = LOC(1) 1
VERTICAL = NO
REVERSE = YES
COMMENTS = "Remove the jumper to Drive only LA17-19"
HELP = "With these pins jumpered address lines SA17-19 and LA17-19
are driven, without a jumper only LA17-19 is driven, some ISA
machines require that this jumper be removed."
JUMPER(5) = 2
NAME = "Controller Address"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y35" "Y33"
FACTORY = LOC(1 2) 11
VERTICAL = NO
REVERSE = YES
COMMENTS = "Use these jumpers to select the controller address, which may
be changed in case of conflict with another card."
HELP = "The controller address may be changed if it conflicts with
another card or to allow a second DPT controller to be added."
JUMPER(6) = 2
NAME = "Host Interrupt Level"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y29" "Y30"
FACTORY = LOC(1 2) 11
VERTICAL = NO
REVERSE = YES
COMMENTS = "Use these jumpers to select Host Interrupt Level, which may
be changed in case of conflict with another card."
HELP = "The Host Interrupt Level may be changed if it conflicts with
another card or to allow a second DPT controller to be added."
JUMPER(7) = 2
NAME = "Host DMA Channel"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y31" "Y32"
FACTORY = LOC(1 2) 11
VERTICAL = NO
REVERSE = YES
COMMENTS = "Use these jumpers to select Host DMA Channel, which may be
changed in case of conflict with another card."
HELP = "The Host DMA Channel may be changed if it conflicts with
another card or to allow a second DPT controller to be added."
JUMPER(8) = 3
NAME = "HBA SCSI ID"
JTYPE = PAIRED
LABEL = LOC(1 2 3) "Y18" "Y25" "Y26"
FACTORY = LOC(1 2 3) 111
VERTICAL = NO
REVERSE = YES
COMMENTS = "Use these jumpers to set SCSI ID. The default for the
PM2011B1 is 7."
HELP = "Each device attached to the same SCSI bus should have a
different SCSI ID. The SCSI ID of the PM2011B1 controller
should normally be at the default of 7."
JUMPER(9) = 2
NAME = "Ignore MEMCS16"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y21" "Y28"
FACTORY = LOC(1 2) 10
VERTICAL = NO
REVERSE = YES
COMMENTS = "Set these jumpers to ignore or decode MEMCS16"
HELP = "Some motherboards do not generate MEMCS16. When the 2011B1 is
used in this kind of system, use these jumpers to force the
2011B1 to run only 16 bit memory cycles."
JUMPER(10) = 1
NAME = "Bus Master DMA Speed"
JTYPE = PAIRED
LABEL = LOC(1) "Y27"
FACTORY = LOC(1) 1
VERTICAL = NO
REVERSE = YES
COMMENTS = "Use these jumpers to Set Bus Master DMA Speed. The default
speed is 4MB/sec but systems with fast memory should be able
to handle 5MB/sec."
HELP = "The default is 4MB/sec, but most systems should be able to
handle 5M/sec if the system has fast memory."
JUMPER(11) = 1
NAME = "Disable Bus Master"
JTYPE = PAIRED
LABEL = LOC(1) "Y24"
FACTORY = LOC(1) 0
VERTICAL = NO
REVERSE = YES
COMMENTS = "Use these jumpers to Enable or Disable Bus Mastering. If
your system will support Bus Mastering, you should enable it
to get higher performance."
HELP = "If your system does not support Bus Mastering, jumper these
pins to Disable Bus Mastering."
JUMPER(12) = 1
NAME = "Firmware ROM Size"
JTYPE = TRIPOLE
LABEL = LOC(1) "Y23"
FACTORY = LOC(1) 0
VERTICAL = NO
REVERSE = NO
COMMENTS = "This jumper should be factory set to the correct setting and
should not require adjustment. The jumper should be in the
lower location for 27256 (32K) size ROM or in the upper
location for 27512 (64K) size."
HELP = "On the DPT2011B1 the ROM size should usually be 256K."
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
GROUP = "Hardware Configuration"
TYPE = "MSD,DSKCTL"
FUNCTION = "Disk Controller"
TYPE = "SCS"
SUBFUNCTION = "I/O Port Address"
COMMENTS = "Select PRIMARY to boot in WD1003 mode.\n"
HELP = "This function allows the controller I/O ports to be used at
the Primary location, which is bootable with a standard BIOS,
or the Secondary location, which is commonly used as a
DISABLE location with slot-specific addressing. Controller
address may be changed in case of conflict with another card."
CONNECTION = "Int SCSI J10\nExt SCSI J11"
CHOICE = "1F0-1F8h (Primary)"
FREE
PORT = 1F0h-1F8h
INIT = JUMPER(5) LOC(1 2) 11
CHOICE = "170-178h"
FREE
PORT = 170h-178h
INIT = JUMPER(5) LOC(1 2) 10
CHOICE = "330-338h"
FREE
PORT = 330h-338h
INIT = JUMPER(5) LOC(1 2) 01
CHOICE = "230-238h"
FREE
PORT = 230h-238h
INIT = JUMPER(5) LOC(1 2) 00
SUBFUNCTION = "Interrupt Number"
COMMENTS = "Select 14-Edge to boot in WD1003 mode.\n"
HELP = "This function allows the controller interrupt number to be
selected either at IRQ 14H, which is bootable with a standard
BIOS, or IRQ 12H or 15H."
CHOICE = "14 - Edge (Bootable)"
FREE
IRQ = 14
TRIGGER = EDGE
INIT = JUMPER(6) LOC(1 2) 11
CHOICE = "15 - Edge"
FREE
IRQ = 15
TRIGGER = EDGE
INIT = JUMPER(6) LOC(1 2) 10
CHOICE = "12 - Edge"
FREE
IRQ = 12
TRIGGER = EDGE
INIT = JUMPER(6) LOC(1 2) 01
SUBFUNCTION = "Host DMA Channel"
COMMENTS = "Host DMA Channel is usually set to DRQ5."
HELP = "Host DMA Channel may be changed in case of conflict with
another card."
CHOICE = "DRQ5"
FREE
DMA = 5
INIT = JUMPER(7) LOC(1 2) 11
CHOICE = "DRQ6"
FREE
DMA = 6
INIT = JUMPER(7) LOC(1 2) 10
CHOICE = "DRQ7"
FREE
DMA = 7
INIT = JUMPER(7) LOC(1 2) 01
CHOICE = "DRQ0"
FREE
DMA = 0
INIT = JUMPER(7) LOC(1 2) 00
SUBFUNCTION = "Option ROM"
COMMENTS = "Select C8000, D8000 or DC000 to allow the BIOS to see the
onboard ROM."
HELP = "This ROM is normally the BR401X SmartROM, an INT13
replacement BIOS, which allows for higher performance, larger
capacity, and easier installation."
CHOICE = "Enabled @ C8000h"
FREE
INIT = JUMPER(3) LOC(1 2) 11
MEMORY = 8K
ADDRESS = 0C8000h
WRITABLE = NO
MEMTYPE = OTH
SIZE = BYTE
CACHE = YES
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(3) LOC(1 2) 00
CHOICE = "Enabled @ D8000h"
FREE
INIT = JUMPER(3) LOC(1 2) 10
MEMORY = 8K
ADDRESS = 0D8000h
WRITABLE = NO
MEMTYPE = OTH
SIZE = BYTE
CACHE = YES
CHOICE = "Enabled @ DC000h"
FREE
INIT = JUMPER(3) LOC(1 2) 01
MEMORY = 8K
ADDRESS = 0DC000h
WRITABLE = NO
MEMTYPE = OTH
SIZE = BYTE
CACHE = YES
FUNCTION = "Bus Mastering Options"
SUBFUNCTION = "Disable Bus Mastering"
COMMENTS = "Choose ENABLED for higher performance."
HELP = "If your system does not support bus mastering choose
DISABLED."
CHOICE = "Enable"
FREE
INIT = JUMPER(11) LOC(1) 0
CHOICE = "Disable"
FREE
INIT = JUMPER(11) LOC(1) 1
SUBFUNCTION = "Bus Master DMA Speed"
COMMENTS = "Default speed is 4MB/sec."
HELP = "Most systems with fast memory should be able to handle
5MB/sec."
CHOICE = "4MB/sec"
FREE
INIT = JUMPER(10) LOC(1) 1
CHOICE = "5MB/sec"
FREE
INIT = JUMPER(10) LOC(1) 0
SUBFUNCTION = "Drive SA and LA17-19"
COMMENTS = "Most ISA machines require SA and LA17-19 to be driven."
HELP = "On some ISA machines address lines LA17-19 are connected to
SA17-19. These machines should be prevented from driving
SA17-19."
CHOICE = "Drive SA and LA17-19"
FREE
INIT = JUMPER(4) LOC(1) 1
CHOICE = "Drive only LA17-19"
FREE
INIT = JUMPER(4) LOC(1) 0
SUBFUNCTION = "Ignore MEMCS16"
COMMENTS = "Ignore forces the 2011 to run only 16 bit memory cycles."
HELP = "Some ISA motherboards do not generate MEMCS16 for accesses to
motherboard memory. When used in this type of system, the
2011 must be forced to always run 16 bit memory cycles."
CHOICE = "Ignore MEMCS16"
FREE
INIT = JUMPER(9) LOC(1 2) 01
CHOICE = "Decode MEMCS16"
FREE
INIT = JUMPER(9) LOC(1 2) 10
FUNCTION = "Floppy Drive"
TYPE = "FDC"
COMMENTS = "Select Primary to enable standard BIOS support of floppy's,
Secondary to enable non-standard BIOS support, and Disable to
use a floppy controller other than the one on this HBA."
HELP = "Secondary is provided to be compatible with the WD1003, but no
BIOS's are known to use this feature."
CONNECTION = "Floppy Connector, J8, Top Middle"
CHOICE = "Primary"
FREE
PORT = 3F0h-3F7h
INIT = JUMPER(2) LOC(1) 0
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(1) LOC(1) 1
CHOICE = "Secondary"
FREE
PORT = 370h-377h
SHARE = YES
INIT = JUMPER(2) LOC(1) 1
FUNCTION = "HBA SCSI ID"
COMMENTS = "Select a SCSI ID for the host bus adapter which is not
currently used by another SCSI device on the same SCSI bus."
HELP = "The controller must have a unique SCSI ID if more than one
SCSI device is attached to the same SCSI Bus."
CHOICE = "7"
FREE
INIT = JUMPER(8) LOC(1 2 3) 111
CHOICE = "0"
FREE
INIT = JUMPER(8) LOC(1 2 3) 000
CHOICE = "1"
FREE
INIT = JUMPER(8) LOC(1 2 3) 010
CHOICE = "2"
FREE
INIT = JUMPER(8) LOC(1 2 3) 100
CHOICE = "3"
FREE
INIT = JUMPER(8) LOC(1 2 3) 110
CHOICE = "4"
FREE
INIT = JUMPER(8) LOC(1 2 3) 001
CHOICE = "5"
FREE
INIT = JUMPER(8) LOC(1 2 3) 011
CHOICE = "6"
FREE
INIT = JUMPER(8) LOC(1 2 3) 101
ENDGROUP
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
FUNCTION = "!DPTA701.CFG Version"
CHOICE = "005D"
FREE
INIT =IOPORT(1) LOC(1) 0
