;
;---------------------------------------------
;       Board Identification Block
;---------------------------------------------
;
BOARD
  ID = "APS0103"
  NAME = "EISA PIP INTERFACE"
  MFR = "AUTOLOGIC INC"
  CATEGORY = "OTH"
  SLOT = EISA
  LENGTH = 172
  READID = YES

JUMPER(1)=11
    NAME="IRQ"
    JTYPE=PAIRED
    REVERSE = NO
    VERTICAL = NO
  COMMENTS = "Interrupt Request Jumper\n
\n This jumper block is the bottom 11 position jumper block.
\n Jumper IRQ is used to select the interrupt request (IRQ)
 lines for the four interrupt channels.
\n Jumper Plug Positions:
\n 1  -  IRQ3  to channel 0 (default)
\n 2  -  IRQ4  to channel 1 (default)
\n 3  -  IRQ5  to channel 2 (default)
\n 4  -  IRQ6  to channel 3 (default)
\n 5  -  IRQ7  to channel 0 
\n 6  -  IRQ9  to channel 1
\n 7  -  IRQ10 to channel 2 
\n 8  -  IRQ11 to channel 3 
\n 9  -  IRQ12 to channel 0 
\n 10 -  IRQ14 to channel 1 
\n 11 -  IRQ15 to channel 2 "
    FACTORY=LOC(11-1) 00000001111

JUMPER(2)=7
    NAME="DRQ"
    JTYPE=PAIRED
    REVERSE = NO
    VERTICAL = NO
  COMMENTS = "DMA Request Jumper\n
\n This is the upper left 7 position jumper block. 
\n Jumper DRQ is used to select the direct-memory-access request
 (DRQ) line for each of the four DMA channels.
\n Make sure the DACK jumpers match the DRQ jumpers
 
\n     Jumper Plug Positions:
\n 1 -  DRQ0 to channel 0 (default)
\n 2 -  DRQ1 to channel 1 (default)
\n 3 -  DRQ2 to channel 2 (default)
\n 4 -  DRQ3 to channel 3 (default)
\n 5 -  DRQ5 to channel 0
\n 6 -  DRQ6 to channel 1
\n 7 -  DRQ7 to channel 2 "
    FACTORY=LOC(7-1) 0001111

JUMPER(3)=7
    NAME="DACK"
    JTYPE=PAIRED
    REVERSE = NO
    VERTICAL = NO
  COMMENTS = "DMA Acknowledge Jumper\n

\n This is the upper right 7 position jumper block. 

\n Jumper DACK is used to select the direct-memory-access
 acknowledge (DACK) line each of the four DMA channels.
\n Make sure the DACK jumpers match the DRQ jumpers

\n Jumper Plug Positions:
\n 1 -  DACK0 to channel 0 (default)
\n 2 -  DACK1 to channel 1 (default)
\n 3 -  DACK2 to channel 2 (default)
\n 4 -  DACK3 to channel 3 (default)
\n 5 -  DACK5 to channel 0
\n 6 -  DACK6 to channel 1
\n 7 -  DACK7 to channel 2 "
    FACTORY=LOC(7-1) 0001111

FUNCTION = "Eisa PIP Interface"
  COMMENTS = "WARNING\n
	     "
  CHOICE = "EISA PIP Interface"