BOARD			; 11/08 fcm Chg STR 205
 ID="ISA8B01"
 NAME="DEC DEPCA EtherLink Adapter, Rev E or F"
 MFR="DEC"
 CATEGORY="NET"
 SLOT=ISA8
 LENGTH=336
 COMMENTS="
The Local Area Disk Driver and Screen Driver must be
installed by adding the following to CONFIG.sys\n
	\tDEVICE=LADDRV.sys\n
	\tDEVICE=ANSI.sys\n\n
The following DOS Environment Variable Recommendations
should also be added to the CONFIG.SYS file.\n
	\tLASTDRIVE=Z\n
	\tBUFFERS=30\n
	\tFILES=20"

JUMPER(1)=5
 JTYPE=TRIPOLE
 NAME="W1-W5"
 LABEL=LOC(1-5) "IRQ2" "IRQ3" "IRQ4" "IRQ5" "IRQ7"
 REVERSE=YES
 FACTORY=LOC(1-5) 10nnn
 COMMENTS="
The top positions specify the Mouse IRQ, the bottom 
positions specify the Network Interface IRQ.\n
Only two jumpers may be used at any one time 
in any of these 5 positions, one on the upper
pins, the other on the lower pins."

JUMPER(2)=1
 JTYPE=PAIRED
 NAME="W6"
 FACTORY=LOC(1) 1
 COMMENTS="I/O Address Range Selection (default is 300h)."

JUMPER(3)=2
 JTYPE=PAIRED
 NAME="W7-W8"
 FACTORY=LOC(2 1) 11
 COMMENTS="
Memory Modes. In order to use the 32k Memory Mode option on 
Rev E or later DEPCA boards, the DECnet PCSA Client Software 
must support this feature. See DECnet SPD to verify support."

JUMPER(4)=6
 JTYPE=TRIPOLE
 NAME="W9-W14"
 REVERSE=YES
 FACTORY=LOC(1-6) 000000
 COMMENTS="
Thinwire/Transceiver Cable Selection.\n
ALL SIX jumpers must be either 
DOWN (Thinwire) or UP (Transceiver).\n
If set UP for Transceiver Connection, remove Jumper from W17 also."

JUMPER(5)=1
 JTYPE=PAIRED
 NAME="W15"
 FACTORY=LOC(1) 1
 COMMENTS="Transceiver Cable Grounding"

JUMPER(6)=1
 JTYPE=PAIRED
 NAME="W16"
 FACTORY=LOC(1) 1
 COMMENTS="
Remote Boot Jumper.\n
Remote Boot feature is supported by
PCSA Client Software Version 2.0 or greater."

JUMPER(7)=1
 JTYPE=PAIRED
 NAME="W17"
 FACTORY=LOC(1) 1
 COMMENTS="DC Power for Thinwire Connection."

FUNCTION="ThinWire/Transcvr(AUI) Network"
 TYPE="NET"
 COMMENTS="Connection can be to ThinWire network or standard Ethernet
 network Transceiver Cable (AUI option). Default is ThinWire."

 CHOICE="ThinWire Network Connection"
 FREE
 INIT=JUMPER(4) LOC(1-6) 000000
 INIT=JUMPER(7) LOC(1) 1
 LINK
 IRQ=2|3|4|5|7
 INIT=JUMPER(1) LOC(1-5) 0nnnn|n0nnn|nn0nn|nnn0n|nnnn0
 LINK
 PORT=300h-30Fh|200h-20Fh
 INIT=JUMPER(2) LOC(1) 1|0

 CHOICE="Transceiver Cable(AUI) Network"
 FREE
 INIT=JUMPER(4) LOC(1-6) 111111
 INIT=JUMPER(7) LOC(1) 0
 LINK
 IRQ=2|3|4|5|7
 INIT=JUMPER(1) LOC(1-5) 0nnnn|n0nnn|nn0nn|nnn0n|nnnn0
 LINK
 PORT=300h-30Fh|200h-20Fh
 INIT=JUMPER(2) LOC(1) 1|0

FUNCTION="Transceiver Cable Ground Option"
 TYPE="NET"
 COMMENTS="If the AUI Cable option is chosen, then if the cable connector
 has 9 pins, remove jumper W15."

 CHOICE="15 Pin Transceiver Connector "
 FREE
 INIT=JUMPER(5) LOC(1) 1

 CHOICE="9 Pin Transceiver Connector"
 FREE
 INIT=JUMPER(5) LOC(1) 0

FUNCTION="DEPCA Mouse"
 TYPE="PTR"
 COMMENTS="Mouse IRQ selected by top positions of W1-W5"

 CHOICE="Enable DEPCA Mouse"
 LINK
 IRQ=2|3|4|5|7
 INIT=JUMPER(1) LOC(1-5) 1nnnn|n1nnn|nn1nn|nnn1n|nnnn1

 CHOICE="Disable DEPCA Mouse"
              
 FREE
 INIT=JUMPER(1) LOC(1-5) nnnnn

FUNCTION="Remote Boot Option"
 TYPE="NET"
 CHOICE="Disable Remote Boot (Default)"
              
 FREE
 INIT=JUMPER(6) LOC(1) 1

 CHOICE="Enable Remote Boot"
 FREE
 INIT=JUMPER(6) LOC(1) 0

FUNCTION="Memory Modes"
 COMMENTS="In order to use the 32k Memory Mode option on Rev E or later
 DEPCA boards, The DECnet PCSA Client Software must support
 this feature. See DECnet SPD to verify support."

 CHOICE="64k Memory Mode (default)"
 LINK
 MEMORY=64k
 ADDRESS=0D0000h|0E0000h
 MEMTYPE=OTHER
 INIT=JUMPER(3) LOC(1-2) 11|01

 CHOICE="32k Memory Mode"
 LINK
 MEMORY=32k
 ADDRESS=0D8000h|0C8000h
 MEMTYPE=OTHER
 INIT=JUMPER(3) LOC(2-1) 01|00