; Copyright (C) 1991, MITAC International Corp.
; Version : V1.00 -- Dec,20 1991
BOARD
ID = "MTC0001"
NAME = "MITAC Venus-100 I/O Expansion Board"
MFR = "MiTAC"
CATEGORY = "MFC"
SLOT = ISA16
READID = NO
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "SIO1/2, PIO, FDC, HDC and VGA Expansion Board"
IOPORT( 1 ) = C00H
SIZE = BYTE
INITVAL = 1FH
IOPORT( 2 ) = 8F8H ; Additional setup status
SIZE = BYTE
INITVAL = 55H
IOPORT( 3 ) = 8F9H ; low byte of index port of MFC
SIZE = BYTE
INITVAL = 22H
IOPORT( 4 ) = 8FAH ; high byte of index port of MFC
SIZE = BYTE
IOPORT( 5 ) = 8FDH ; ioport address of system control 3
SIZE = BYTE
JUMPER( 1 ) = 2
NAME = "JP1"
JTYPE = INLINE
VERTICAL = NO
REVERSE = YES
LABEL = LOC( 1^2 2^3 ) "Disable" "Enable"
INITVAL = LOC( 1^2 2^3 ) 01
COMMENTS = "Disable/Enable IDE hard disk interface"
JUMPER( 4 ) = 2
NAME = "JP4"
JTYPE = INLINE
VERTICAL = NO
REVERSE = YES
LABEL = LOC( 1^2 2^3 ) "Not Passed" "Passed"
INITVAL = LOC( 1^2 2^3 ) 10
COMMENTS = "Video IRQ9 signal passed/not passed to system"
JUMPER( 5 ) = 2
NAME = "JP5"
JTYPE = INLINE
VERTICAL = NO
REVERSE = YES
LABEL = LOC( 1^2 2^3 ) "Non-interl" "Interlace"
INITVAL = LOC( 1^2 2^3 ) 10
COMMENTS = "Configure VGA to Non-interlace/Interlace mode"
JUMPER( 6 ) = 2
NAME = "JP6"
JTYPE = INLINE
VERTICAL = NO
REVERSE = YES
LABEL = LOC( 1^2 2^3 ) "16-bit" "8-bit"
INITVAL = LOC( 1^2 2^3 ) 10
COMMENTS = "Configure the adapter for an 16-bit/8-bit slot"
JUMPER( 10 ) = 2
NAME = "JP10"
JTYPE = INLINE
VERTICAL = YES
REVERSE = YES
LABEL = LOC( 1^2 2^3 ) "Enable" "Disable"
INITVAL = LOC( 1^2 2^3 ) 10
COMMENTS = "Enable/Disable floppy disk controller"
JUMPER( 11 ) = 2
NAME = "JP11"
JTYPE = INLINE
VERTICAL = YES
REVERSE = YES
LABEL = LOC( 1^2 2^3 ) "Select" "Not Used"
INITVAL = LOC( 1^2 2^3 ) 10
COMMENTS = "DR0,DR1,MTR0,MTR1 pins select drive0,drive1\n
motor0,motor1 respectively.\n
This JUMPER is reserved, please don't change !"
JUMPER( 7 ) = 2
NAME = "JP7,JP12"
JTYPE = TRIPOLE
VERTICAL = NO
REVERSE = YES
LABEL = LOC( 1 2 ) "JP7" "JP12"
INITVAL = LOC( 1 2 ) 11
COMMENTS = "JP7 JP12 \n
1 - 2 1 - 2 : PIO enabled at LPT2 (378-37A)\n
1 - 2 2 - 3 : PIO enabled at LPT1 (3BC-3BE)\n
2 - 3 1 - 2 : PIO enabled at LPT3 (278-27A)\n
2 - 3 2 - 3 : PIO disabled\n "
JUMPER( 8 ) = 3
NAME = "JP8,JP9,JP13"
JTYPE = TRIPOLE
VERTICAL = NO
REVERSE = YES
LABEL = LOC( 1 2 3 ) "JP8" "JP9" "JP13"
INITVAL = LOC( 1 2 3 ) 111
COMMENTS = "JP8 JP9 JP13 RS232C#1 RS232C#2 \n
1 - 2 1 - 2 1 - 2 : COM1(3F8-3FF) COM2(2F8-2FF)\n
1 - 2 1 - 2 2 - 3 : Disabled COM2(2F8-2FF)\n
1 - 2 2 - 3 1 - 2 : COM1(3F8-3FF) Disabled \n
1 - 2 2 - 3 2 - 3 : Disabled Disabled \n
2 - 3 1 - 2 1 - 2 : COM2(2F8-2FF) COM1(3F8-3FF)\n
2 - 3 1 - 2 2 - 3 : Disabled COM1(3F8-3FF)\n
2 - 3 2 - 3 1 - 2 : COM2(2F8-2FF) Disabled \n
2 - 3 2 - 3 2 - 3 : Disabled Disabled "
FUNCTION = "Control Port Select"
SHOW = NO
CHOICE = "Control Port 321H"
FREE
PORT = 321H
INIT = IOPORT( 4 ) 00H
FUNCTION = "Serial Port 1"
CHOICE = "COM1 Enabled"
FREE
PORT = 3F8H - 3FFH
IRQ = 4
INIT = IOPORT( 5 ) LOC( 6 ) 1
CHOICE = "COM1 Disabled"
INIT = IOPORT( 5 ) LOC( 6 ) 0
FUNCTION = "Serial Port 2"
CHOICE = "COM2 Enabled"
FREE
PORT = 2F8H - 2FFH
IRQ = 3
INIT = IOPORT( 5 ) LOC( 7 ) 1
CHOICE = "COM2 Disabled"
INIT = IOPORT( 5 ) LOC( 7 ) 0
FUNCTION = "Parallel Port"
CHOICE = "PIO Enabled"
SUBCHOICE
FREE
PORT = 378H - 37AH
IRQ = 7
INIT= IOPORT( 5 ) LOC( 5 4 ) 10
SUBCHOICE
FREE
PORT = 278H - 27AH
IRQ = 5
INIT = IOPORT( 5 ) LOC( 5 4 ) 11
SUBCHOICE
FREE
PORT = 3BCH - 3BEH
IRQ = 7
INIT = IOPORT( 5 ) LOC( 5 4 ) 01
CHOICE = "PIO Disabled"
FREE
INIT = IOPORT( 5 ) LOC( 5 4 ) 00
FUNCTION = "Serial Port Lock While Key Lock"
CHOICE = "SIO Lock Enabled"
FREE
INIT = IOPORT( 5 ) LOC( 3 ) 1
CHOICE = "SIO Lock Disabled"
FREE
INIT = IOPORT( 5 ) LOC( 3 ) 0
FUNCTION = "Parallel Port Lock While Key Lock"
CHOICE = "PIO Lock Enabled"
FREE
INIT = IOPORT( 5 ) LOC( 2 ) 1
CHOICE = "PIO Lock Disabled"
FREE
INIT = IOPORT( 5 ) LOC( 2 ) 0
FUNCTION = "Floppy Disk Controller"
CHOICE = "FDC Enabled"
FREE
PORT = 3F0H - 3F7H
IRQ = 6
INIT = IOPORT( 5 ) LOC( 1 ) 1
CHOICE = "FDC Disabled"
FREE
INIT = IOPORT( 5 ) LOC( 1 ) 0
FUNCTION = "Hard Disk Controller"
CHOICE = "HDC Enabled"
FREE
PORT = 1F0H - 1F7H
IRQ = 14
INIT = IOPORT( 5 ) LOC( 0 ) 1
CHOICE = "HDC Disabled"
FREE
INIT = IOPORT( 5 ) LOC( 0 ) 0
FUNCTION = "VGA"
SHOW = NO
CHOICE = "VGA Enabled"
FREE
MEMORY = 64K
ADDRESS = 0A0000H ; Display Memory ( Graphics Mode )
SIZE = WORD
WRITABLE = YES
MEMTYPE = OTH
MEMORY = 32K
ADDRESS = 0B0000H ; Display Memory ( Monochrome Text Mode )
SIZE = WORD ; Hercules Graphics Page 0
WRITABLE = YES
MEMTYPE = OTH
MEMORY = 32K
ADDRESS = 0B8000H ; Display Memory ( Color Text and CGA Graphics )
SIZE = WORD ; Hercules Graphics Page 1
WRITABLE = YES
MEMTYPE = OTH
MEMORY = 32K
ADDRESS = 0C0000H ; EGA/VGA BIOS
SIZE = WORD
WRITABLE = NO
MEMTYPE = OTH
PORT = 03C0h-03CAh
PORT = 03CCh
PORT = 03CEh-03CFh
PORT = 03B4h-03B5h
PORT = 03BAh
PORT = 03D4h-03D5h
PORT = 03DAh
