STANDARD MICROSYSTEMS CORPORATION

                      DEC PATHWORKS v4.1 for DOS
                      For Ethernet LAN Adapters

                          INSTALLATION GUIDE

   This software is licensed by SMC for use by its customers only.
        Copyright (c) 1994 Standard Microsystems Corporation.
                         All rights reserved.


This installation guide describes how to:

o  Use EZStart to copy the DEC PATHWORKS version 4.1 for DOS 
   NDIS driver files from the SuperDisk to your PC.

o  Prepare your operating system so you can attach to the network.

Note: This driver supports all 8216 (Ultra), 80xx (Elite),  
      80xx (PLUS), and 8416 (EtherEZ) Series ISA, EISA, and Micro
      Channel Ethernet adapters.


COPYING THE DRIVER FILES

From the Driver Installation screen, select 'Copy Files' to copy all 
the files used by this driver from the SuperDisk to the Destination
Directory recommended by EZStart, or to a different directory that 
you specify.


PREPARING YOUR OPERATING SYSTEM

1. Insert the DEC Pathworks Client Setup diskette #1 into your 
   computer's disk drive.

2. Type: NETSETUP

3. Press the Enter key.

4. When prompted about whether you have an LK250 keyboard, specify 
   'N(o)' if you do not have this type of keyboard.

5. Select the DECNET option and press Enter.

6. Insert the DNET TRNSPRT 1 diskette into your computer's disk drive.

7. Specify the destination drive letter.

8. When the prompt 'Are you creating an initial workstation 
   diskette' appears, select N(o).

9. Type the node name and address. 

10. Press Enter.

11. Type the server node name and number.

12. When prompted to add LK250 keyboard setup to AUTOEXEC.BAT file, 
    select N(o).

13. Select 'Ethernet' and press Enter.

14. Select 'LAN Manager-Supplied NDIS'.

15. Press the Enter key twice.

16. Select 'Western Digital EtherCard - WD8003E' option and press 
    Enter.

17. Press F9 to write the key disk. Then press Enter.

18. Press Enter to accept the default PROTOCOL.INI.

19. Follow the screen prompts.

20. After the Write Key Disk procedure is done, press F10 from the
    Configuration screen to exit to DOS.

21. Locate PROTOCOL.INI file in the directory where EZStart
    copied the driver (default is C:\DECNET). Then rename this file
    to PROTOCOL.DEC. Then rename the DEC41DOS.INI (located in the
    same subdirectory as the file you just renamed) to PROTOCOL.INI.

22. Using any text editor, edit the CONFIG.SYS file by replacing 
    the line:

        device=\DECNET\MACWD.DOS

    with this line:

        device=\DECNET\SMC8000.DOS

23. Make sure the ni_irq value in the [DATALINK] section matches 
    the irq value of the network adapter specified in the 
    PROTOCOL.INI file.


This commercial computer software and documentation is provided with
RESTRICTED RIGHTS.  Use, duplication, or disclosure by the
Government is subject to restrictions set forth in subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer Software
clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the
Commercial Computer Software -- Restricted Rights clause at
FAR 52.227-19, or Alternate III of the Rights in Data -- General
clause at FAR 52.227-14, as applicable.  The manufacturer /
subcontractor is Standard Microsystems Corporation,   80 Arkay Drive,
Hauppauge,  NY    11788. 


SMC and Standard Microsystems are registered trademarks; and EtherEZ,
EtherCard Elite 16 Ultra, EtherCard Elite 16T Ultra, EtherCard Elite
16C Ultra, EliteSeries, EZStart, and SuperDisk are trademarks of 
Standard Microsystems Corporation.  Other product and company names 
are registered trademarks or trademarks of their respective holders.