; OEMSETUP FILE FOR ND5200 based Ethernet adapters
; Platform type: Ix86
; WNT version 3.1
; Supported adapters:
; NDC ND5200 PCI Ethernet Controller
;
; National DataComm Corporation, Hsinchu, Taiwan.
;
; The information in this software is subject to change without notice
; and should not be construed as a commitment by National DataComm
; Corporation.
;
; NDC assumes no responsibility for the use or reliability of its
; software on equipment which is not supplied by NDC.
;
; Usage:
;
; This file is the installation/configuration/deinstallation
; procedure of the NDC ND5200 driver for Windows NT. It can be called
; from Windows Setup directly, or via the Windows NT Networks
; Control Program Applet (NCPA) from inside the Windows
; Control Panel.
;
;----------------------------------------------------------------------------------------
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
ISA
EISA
"Jazz-Internal Bus"
PCI
[Options]
ND5200
[ConnectionChoicesND5200]
Connect_0 = "AutoDetection" , 0
Connect_1 = "Twisted Pair" , 2
Connect_2 = "Twisted Pair - Full Duplex " , 3
Connect_3 = "Twisted Pair - No Link Test" , 4
Connect_4 = "BNC - Thinwire (BNC connector)" , 1
Connect_5 = "AUI - Thickwire (15_pin connector)" , 5
[FileConstants]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "NatioanlDatacommCorporation"
ProductMajorVersion = "1"
ProductMinorVersion = "0"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
PciMechanism = 0
ProductSoftwareName = "ND5200_"
ProductSoftwareTitle = "NDC ND5200 Adapter Driver"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\ND5200.sys"
NetRuleSoftwareType = "ND5200Sys ndisDriver ND5200Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """ND5200Sys"" yes no container"
NetRuleSoftwareClass = {"ND5200Driver basic"}
NetRuleSoftwareSWBindable = {+
"ND5200Driver ND5200Adapter non exclusive 100"}
OptionHelpFile = "ND5200.hlp"
ProductHardwareName = "ND5200_"
ProductHardwareND5200Title = "NDC ND5200 PCI Ethernet Controller"
NetRuleHardwareND5200Type = "ND5200 ND5200Adapter"
NetRuleHardwareND5200Class = {"ND5200Adapter basic"}
AdapterND5200Type = 5 ;; PCI board
HelpND5200Id = 10
ND5200CFID = 135185 ;; 0x00021011
NetRuleHardwareBindForm = " yes yes container"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
LoopCount = 0
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
[ReturnOptions]
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
[InstallOption]
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "\n"
read-syms GeneralConstants
read-syms FileConstants
set NetRuleSoftwareBindable = $($R1)
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(Function$(Option)Title)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
EndWait
Begin = +
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
;; set CommonStatus = STATUS_REBOOT
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else-ifstr(i) $(Option) == "DE425"
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_HARDWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else
set StartLabel = configureadapter
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
set from = $(fatal)
set to = $(fatal)
goto $(StartLabel)
installadapter = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto end
else
Shell $(UtilityInf), CardExistedDlg
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) != "OK"
set CommonStatus = STATUS_USERCANCEL
goto end
endif
set OldVersionExisted = $(TRUE)
endif
Endif
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
install "Install-Hlp"
Goto adapteroptions
configureadapter = +
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Goto fatalregistry
Endif
Endif
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Goto fatalregistry
endif
set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
Ifstr(i) $(ValueName) == "ConnectionType"
set ConnectionIndex = $(ValueData)
endif
EndForListDo
set ConnectionValue = *($(ConnectionList), ~($(ConnectionValues),$(ConnectionIndex)))
ifstr(i) $(ConnectionValue) == ""
set ConnectionValue = *($(ConnectionList), 2)
endif
adapteroptions = +
ifstr(i) $(Option) != "DE425"
set from = adapteroptions
read-syms FileDependentDlg$(!STF_LANGUAGE)
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set ConnectionIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
ui pop 1
goto end
endif
set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
ifstr(i) $(!NTN_InstallMode) == configure
goto updateparameters
endif
endif
installproduct =+
StartWait
ifstr(i) $(Option) == "DE425"
Shell $(UtilityInf), EISAFindBus, $($(Option)_1BYTE),$(EISA_MASK)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == {}
set Error = $(CANNOT_FIND_ANY_CARD)
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
endif
set AdapterList = $($R1)
ifint $(OldVersionExisted) == $(FALSE)
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
Set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
goto fatalregistry
endif
endif
ForListDo $(AdapterList)
set BusNum = *($($),1)
ifstr(i) $(Option) == "DE425"
set SlotNum = *($($),2)
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), +
$(SlotNum), $(ProductHardware$(Option)Description), $(ProductHardwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) != "YES"
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), +
$(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
;; Shell $(UtilityInf), GetBusTypeNum
;; set BusTypeNum = $($R1)
;; ifint $($ShellCode) != $(!SHELL_CODE_OK)
;; goto ShellCodeError
;; endif
set BusTypeNum = 2
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
CloseRegKey $(HardParameterKey)
endif
else
ifstr(i) $(Option) == "DE436"
set LoopCount = {1,2,3,4}
endif
ForListDo $(LoopCount)
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
;; Shell $(UtilityInf), GetBusTypeNum
;; set BusTypeNum = $($R1)
;; ifint $($ShellCode) != $(!SHELL_CODE_OK)
;; goto ShellCodeError
;; endif
set BusTypeNum = 5
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
{PciMechanism,$(NoTitle),$(!REG_VT_DWORD),$(PciMechanism)},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
CloseRegKey $(HardParameterKey)
EndForListDo
endif
EndForListDo
EndWait
goto successful
updateparameters =+
set HardParameterKey = $($R3)
set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}
ifstr(i) $(Option) == "DE436"
set LoopCount = {1,2,3,4}
endif
ForListDo $(LoopCount)
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(KeyParameters)
EndForListDo
goto successful
bindingadapter =+
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Set CommonStatus = STATUS_USERCANCEL
Set Severity = STATUS
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Hlp]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Source Media Descriptions]
1 = "Windows NT Setup Disk #1" , TAGFILE = i386\nt31\ND5200.sys
2 = "Windows NT - ND5200 Driver Setup Floppy" , TAGFILE = i386\nt31\ND5200.sys
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
2, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename)
[Files-Hlp]
2,ND5200.hlp , SIZE=88888
[Files-ND5200]
2,ND5200.SYS , SIZE=88888
[LanguagesSupported]
ENG
[OptionsTextENG]
ND5200 = "NDC ND5200 PCI Ethernet Controller"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
ProductSoftwareDescription = "NDC ND5200 Adapter Driver"
FunctionND5200Title = "NDC ND5200 PCI Ethernet Controller Setup"
ProductHardwareND5200Description = "NDC ND5200 PCI Ethernet Controller"
ConnectionList = ^(ConnectionChoices$(Option), 1)
ConnectionValues = ^(ConnectionChoices$(Option), 2)
NoList = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(Function$(Option)Title)
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Network card is not present in the system"
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG]
DlgTemplate = "ADAP_PROTO_COMBO"
DlgType = "Combination"
Caption = $(Function$(Option)Title)
DlgText = "Choose the proper cable type for the "+
"network adapter. Select [Help] for a detailled "+
"description of the available options of the list"
Combo1Label = "&Connection Type:"
Combo1List = $(ConnectionList)
Combo1Out = $(ConnectionValue)
ComboListItemsIn = {Combo1List}
ComboListItemsOut = {Combo1Out}
EditTextLim = ""
CBOptionsGreyed = {}
MinHelpId = 10
MaxHelpId = 1050
HelpContext = $(Help$(Option)Id)
