NDC Instant-Link Ethernet PCMCIA Adapter (ND51XX)
NDIS Driver for FTP PC/TCP for (DOS) Installation
=================================================

PRE-INSTALLATION

     Before installing the NOS or network applications, you should first
     run NDCONF1 to configure and diagnose the Instant-Link adapter(s).
     We recommend you to select "Update CONFIG.SYS" in the "Configuration
     Menu" before exiting NDCONF1.


INSTALLATION PROCEDURE

1)   Insert the NDC Setup diskette into drive A: and copy NE2000 NDIS
     driver to the destination subdirectory of your PC (the
     recommended Destination Subdirectory is C:\PCTCP).

          A:\> Copy A:\NDIS\NE2000.DOS C:\PCTCP

2)   Refer to Chapter 5 of the PC/TCP Installation and
     Configuration Guide, entitled "Using an NDIS Driver with the
     Generic Kernel".

3)   Copy the netbind files from the \NDIS subdirectory on FTP Disk
     A, labeled "Unsupported Network Software".

4)   Using any text editor, add the following lines to your
     workstation's CONFIG.SYS file:

          DEVICE=C:\PCTCP\PROTMAN.SYS /I:C:\PCTCP
          DEVICE=C:\PCTCP\NE2000.DOS
          DEVICE=C:\PCTCP\DIS_PKT.GRP

     Adjust the drive and path specifications to match your
     installation.

5)   Use any text editor to make the PROTOCOL.FTP file in the
     \PCTCP subdirectory on your PC's hard drive to look as
     follows:

          [Protocol Manager]:
               Drivername = protman$

          [PKTDRV]
               Drivername = pktdrv$
               Bindings = NE2000_NIF
               Intvec = 0x60
               Chainvec = 0x65

          [NE2000_NIF]
               DriverName = MS2000$
               INTERRUPT = 3
               IOBASE = 0x300

     where the values for "INTERRUPT" and "IOBASE" must match what
     you specified by NDCONF1.

6)   Rename the PROTOCOL.FTP file to PROTOCOL.INI. Refer to your
     DOS manual if you need assistance.

7)   Proceed with the rest of the instructions in the PC/TCP
     Installation and Configuration Guide.


NDC Instant-Link Ethernet PCMCIA Adapter (ND51XX)
Packet Driver for FTP PC/TCP for (DOS) Installation
===================================================

PRE-INSTALLATION

     Before installing the NOS or network applications, you should first
     run NDCONF1 to configure and diagnose the Instant-Link adapter(s).
     We recommend you to select "Update CONFIG.SYS" in the "Configuration
     Menu" before exiting NDCONF1.


INSTALLATION PROCEDURE

1)   Insert PC/TCP Netware Software for DOS "Disk 1" into drive
     A: or B: .

2)   Go to drive A: or B: and type: "INSTALL" and press <Enter>.

3).  When you are installing the PC/TCP generic kernel, the
     Operating Environment menu lists 12 environments. Please
     select an IEEE 802.3 packet driver, answer "Y" in the "Pkt Drv"
     field. When you have selected the type of driver appropriate
     to network configuration, press F10 and continue the installation.

4)   Edit the AUTOEXEC.FTP.

     - Replace:

          echo Run packet driver here.

     with:

          NE2000PK 0x60 3 0x300
          ETHDRV

     where the packet driver (NE2000PK.COM) will use
     software interrupt vector 0x60 for NE2000 compatible adapter
     with IRQ=3, IO_BASE=0x300.

     Note: Packet Driver Basic Syntax:

          NE2000PK <PD_INT_NO> [IRQ] [IO_BASE]

     where:

     <PD_INT_NO>    This specifies the software interrupt (IRQ)
                    where you'll load the packet driver. It must
                    be in the range 0x60 to 0x80.

                    The PC/TCP kernel, by default, is loaded at
                    interrupt 0x61 (so don't load the packet
                    driver there!)

     [IRQ]          This specifies the hardware interrupt (IRQ) of
                    your card.

     [IO_BASE]      This specifies the I/O address of your card.

5)   Copy ETHDRV.EXE file from "PC/TCP Network Software for DOS
     disk 2" to your PC/TCP directory (usually C:\PCTCP).

6)   Insert the NDC Setup diskette to drive A: and copy NE2000 Packet
     driver to the destination subdirectory on your PC (the recommended
     Destination Subdirectory is C:\PCTCP).

          A:\> Copy A:\PACKET\NE2000PK.COM C:\PCTCP

     (Note: You may also replace NE2000PK.COM with the NE2000
     packet driver "NE2000.COM" from "PC/TCP Netware Software for
     DOS, Unsupported Network Software disk B:".)

7)   To preserve your current AUTOEXEC.BAT file, rename it to
     AUTOEXEC.OLD.

          REN C:\AUTOEXEC.BAT C:\AUTOEXEC.OLD

     Copy AUTOEXEC.FTP to AUTOEXEC.BAT

          COPY C:\AUTOEXEC.FTP C:\AUTOEXEC.BAT

     This complete the installation of FTP PC/TCP.