┌───────────────────────────────────────────────────────────────┐
│		  ACCTON TECHNOLOGY CORPORATION 		│
│	  ETHERPOCKET PC-NFS SOFTWARE INTERFACE DRIVER		│
│		       INSTALLATION GUIDE			│
│								│
│		   06/01/1991 VERSION 1.00 R02			│
│								│
│	Copyright 1989-1992 ACCTON Technology Corporation	│
│		      All rights reserved.			│
└───────────────────────────────────────────────────────────────┘

You  have  just  opened the PC-NFS  READ.ME  file.   It  contains
instructions on the PC-NFS Software Interface Driver installation
for the following EtherPocket lan adapters :

	┌────────────────────────────────────────────┐
	│   Product Name	    Product Number   │
	├────────────────────────────────────────────┤
	│  EtherPocket-10T	       EN2201	     │
	│  EtherPocket-CX	       EN2202	     │
	│  EtherPocket-Duo	       EN2209	     │
	└────────────────────────────────────────────┘


Using any ACCTON EtherPocket-CX/10T/Duo (EN2202/EN2201/EN2209) lan
adapter and the ACCTON PC-NFS Software Interface Driver, you can run the
Sun MicroSystems PC-NFS on your PC.

The following files will be used in this installation:

    Files	   Contents
    --------	   --------------------------------------------------------
    PCNFSIF.SYS    PC-NFS Software Interface Driver.
    PEPKTDRV.COM   ACCTON Packet Driver for EtherPocket-CX/10T lan adapter.


The steps to install the program are as follows:

1.  Start the installation process by following the procedure
    described  in  the	PC-NFS	Manual for installing the Sun
    Microsystems PC-NFS program in your PC's hard disk.  When
    asked to identify the type of network interface  card you
    are using, select "WD8003" from the list.  Likewise, when
    asked  for	the interrupt level  and the base I/O address
    select:

	       Interrupt Level (IRQ) 3
	       I/O Base Address 300h

2.  Copy the  following files to  the \NFS  directory of your
    hard disk:

	       PCNFSIF.SYS
	       PEPKTDRV.COM

3.  Modify the CONFIG.SYS file to include the following:

	       DEVICE=C:\ANSI.SYS
	       DEVICE=C:\NFS\PCNFS.SYS
	       DEVICE=C:\NFS\SOCKDRV.SYS
	       DEVICE=C:\NFS\PCNFSIF.SYS
	       LASTDRIVE=V

4.  Create or modify an existing AUTOEXEC.BAT file to include
    the following:

	       C:\NFS\PEPKTDRV 98
	       SET PATH = C:\; C:\NFS
	       SET TZ=CST6
	       SET NFSDRIVE=C
	       PRT *
	       NFSRUN

    For your  system  to  work	properly,  make  sure  that the
    C:\NFS\PEPKTDRV 98 command line is placed before the NFSRUN
    command line.  For more  information  on  the  PEPKTDRV.COM
    program, refer to the  READ.ME  file  of  the ACCTON Packet
    Driver.

    Allowable values for the software interrupt vector range from
    96 to 128.	The default software interrupt vector value is 98.

5.  Reboot the PC and start the PC-NFS program.  You may now run
    PC-NFS commands on your PC to allow communication with other
    computers on the network that use the TCP/IP protocol.