ISA NE-Series Ethernet Adapter
       NDIS DRIVER FOR SUN PC-NFS Installation
       =======================================

The drivers named ETHNE contained in the directory
NDIS conform to the Network Driver Interface
Specification (NDIS) defined by Microsoft/3Com.


NDIS Driver Installation on SUN PC-NFS
--------------------------------------
1. Edit the CONFIG.SYS file to include the following
   command line, and reboot the PC:

   Device=c:\dos\ansi.sys

2. Insert the PC-NFS Installation diskette into the
   PC's floppy drive. Type the following from DOS and
   press <Enter> to bring up the PC-NFS installation
   screen:

   INSTALL	<Enter>

3. Follow screen prompts to configure your screen
   display. For example, press <M> to choose mono display,
   or press <C> to choose color display, or press
   <ESC> to cancel the installation.

4. When the "Install the Basic PC-NFS files" window
   appears onscreen, select "Install Full PC-NFS" from
   the choice list.

5. "Specify the target PC-NFS installation directory," by
   typing the appropriate path in the field provided. For
   example, C:\NFS. Then press <Enter> to continue.

6. Carefully read and respond to each prompt that
   appears onscreen, indicating the suitable
   selections for your system.

7. When you reach the prompt that reads, "Configure
   an Ethernet network connection," choose "Ethernet"
   from the choice list. Then press <Enter> to confirm
   your choice.

8. Choose the network adapter you will use. Select
   "NDIS" from the list shown onscreen. Then press
   <Enter> to confirm your choice.

9. Follow screen instructions to complete the process. You
   will be prompted to insert some PC-NFS distribution
   diskettes. And during the process, files from
   the diskettes will be copied into your hard disk
   drive.

10. When prompted to update your AUTOEXEC.BAT and
    CONFIG.SYS files, press "Y."

11. Your system will prompt you when the installation
    process is complete. It will display the following
    message, "PC-NFS installation is complete."

12. The system will create two subdirectories
    in the destination drive, namely, \LANMAN and \NFS.

13. Create the NETWORK.BAT, DRIVES,BAT and HOSTS files.
    Specify the PC name, IP address, server name
    and server IP address in these files.
    See the section on Sample Configuration Files
    for examples.

14. Copy the NETWORK.BAT, DRIVES.BAT and HOSTS files
    into the \NFS directory of your server.

15. Copy the ETHNE.DOS file from the
    \MSLANMAN.DOS\DRIVERS\ETHERNET\NDIS2 of your Driver Diskette
    to the newly created subdirectory (\LANMAN) on your
    destination drive.

    Note: The ETHNE.DOS file is also found in the \NDIS\DOS
	  directory of your Driver Diskette.

16. Edit the CONFIG.SYS file using a text editor. Add
    the following command line before the NFS_NDIS
    driver specification:

      DEVICE=C:\LANMAN\ETHNE.DOS

17. Edit the PROTOCOL.INI file in the \LANMAN directory,
    replacing the following:

    a. Replace the section name [your-mac-module]
       with [NDIS2]
    b. Replace the command line "drivername = YOURMAC$" with
       "drivername = ETHNE$"
    c. Specify the correct IRQ and IOBASE value
       (may be omitted) to match the adapter's
       hardware configuration. For example:
       IRQ = 3
       IOBASE = 0x300
    d. Replace the command line "bindings = YOUR-MAC-MODULE"
       with "bindings = ETHNE$"

18. Reboot your computer. Then start the application
    you need. For example:
    a. Execute NFSCONF.EXE to configure the system,
       such as mounting a virtual drive E:
    b. Execute TELNET.EXE to do terminal emulation

Sample Configuration Files
--------------------------

1. NETWORK.BAT

   REM stc* is a sample PC-NFS workstation name
   REM nfsuser is a sample PC-NFS server address
   NET START RDR stc*
   NET PCNFSD nfsuser
   NET NAME stc*

2. DRIVES.BAT

   REM specify connections to remote directory
   NET USE l:nfsuser:/usr2/down
   NET USE k:nfsuser:/mnt

3. HOSTS

   REM specify gateway address
   192.72.24.201 <gateway # updated>
   REM specify workstation's IP address
   192.72.24.102 stc
   REM specify server's IP address
   192.72.24.202 nfsuser

4. CONFIG.SYS

   shell=c:\command.com /P /E:526
   dos=high, UMB
   rem ----pcnfs install
   Device=c:\dos\ansi.sys
   DEVICE=C:\NFS\PCNFS.SYS  /m
   DEVICE=C:\NFS\SOCKDRV.SYS
   REM Specify PROTOCOL.INI directory
   DEVICE=C:\LANMAN\PROTMAN.SYS /i:C:\LANMAN
   REM NDIS driver name
   device=C:\LANMAN\ETHNE.DOS
   DEVICE=C:\LANMAN\NFS-NDIS.SYS
   FILES=50
   BUFFERS=50
   LASTDRIVE=v
   STACKS=9,256

5. PROTOCOL.INI file at the \LANMAN directory

   [protocol manager]
      drivername = PROTMAN$
   [ETHNE]
      drivername = ethne$
      irq = 3
      iobase = 0x300
   [NFS-NDIS]
      drivername = NFSLINK1
      bindings = ETHNE

6. AUTOEXEC.BAT
   ...
   SET TZ=PST8
   SET path=C:\;C:\NFS;C:\LANMAN
   SET NFSDRIVE=D
   REM Add the following line to bind NDIS driver
   C:lanman\netbind
   PRT *
   REM Execute application you need, e.g. NFSRUN
   NFSRUN

===End===