VER: 3.00
SYN: 1.00
DR PCNTNW
{
DES: $PCNTNW_1
HELP: $PCNTNW_2
PAR: 3.00
FILE: PCNTNW.LAN
; OF: MSM.NLM, ETHERTSM.NLM
LI BUSTYPE OPT
{
DES: $PCNTNW_3
HELP: $PCNTNW_4
CD: 'ISA'
CH: 'PNP'
CD: 'PCI'
CH: 'PCI'
CD: 'PCI1'
CH: 'PCI1'
CD: 'PCI2'
CH: 'PCI2'
OUT: 'BUSTYPE=%s'
}
PR PORT OPT
{
DES: $PCNTNW_9
HELP: $PCNTNW_10
TYP: HEX(4)
VAL: 0000 - FFFF
RES: 20
OUT: 'PORT=%s'
}
PR BOARD if ( PORT == UNDEFINED) REQ ELSE OPT
{
DES: $PCNTNW_7
HELP: $PCNTNW_8
TYP: DEC(4)
VAL: 0001 - 0254
OUT: 'BOARD=%s'
}
PR INT OPT
{
DES: $PCNTNW_11
HELP: $PCNTNW_12
TYP: HEX
VAL: 1 - F
OUT: 'INT=%s'
}
PR DMA if ( BUSTYPE == UNDEFINED or BUSTYPE == 1 ) OPT else HID
{
DES: $PCNTNW_13
HELP: $PCNTNW_14
TYP: HEX
VAL: 3, 5, 6, 7
OUT: 'DMA=%s'
}
FR FrameSelect
{
CH: 'Ethernet_802.2'
CH: 'Ethernet_802.3'
CH: 'Ethernet_SNAP'
CH: 'Ethernet_II'
DEF: 1, 2
}
LI FDUP OPT
{
DES: $PCNTNW_15
HELP: $PCNTNW_16
CD: 'Turn Off the Full Duplex function.'
CH: 'OFF'
CD: 'Full Duplex on 10 Base-T Port.'
CH: 'UTP'
CD: 'Full Duplex on AUI port.'
CH: 'AUI'
OUT: 'FDUP=%s'
}
PR NODE
{
}
}
DLANG: 4
;English
$PCNTNW_1 = "AMD PCnet Family (EtherTeam PCI/ISA) Network Driver"
$PCNTNW_2 = "This driver (PCNTNW.LAN) supports both EtherTeam ISA
and EtherTeam PCI network adapters."
$PCNTNW_3 = "Bus Type of the adapter installed."
$PCNTNW_4 = "As default, all bus types are scanned. If
explicitly specified, then only that bus
type is scanned."
$PCNTNW_7 = "Physical Board Number"
$PCNTNW_8 = "This keyword is applied only if you need to add
multiple frame types, and you have not defined
the board explicitly by using its port address."
$PCNTNW_9 = "I/O port address of the network device."
$PCNTNW_10 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 0200 - 03E0
in 20h steps
\nSupported values for EtherTeam PCI: 0000 - FFE0
in 20h steps"
$PCNTNW_11 = "IRQ number of the networking board"
$PCNTNW_12 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 3, 4, 5, 9, A, B, F
\nSupported values for EtherTeam PCI: 1 - F"
$PCNTNW_13 = "DMA channel of the networking board."
$PCNTNW_14 = "This option applies to EtherTeam ISA only.
Found by scan as default. If explicitly specified,
must match with its actual value."
$PCNTNW_15 = "Full Duplex Support."
$PCNTNW_16 = "Change the Default Full Duplex operation."
LANG: 6
;French
$PCNTNW_1 = "AMD PCnet Family (EtherTeam PCI/ISA) Network Driver"
$PCNTNW_2 = "This driver (PCNTNW.LAN) supports both EtherTeam ISA
and EtherTeam PCI network adapters."
$PCNTNW_3 = "Bus Type of the adapter installed."
$PCNTNW_4 = "As default, all bus types are scanned. If
explicitly specified, then only that bus
type is scanned."
$PCNTNW_7 = "Physical Board Number"
$PCNTNW_8 = "This keyword is applied only if you need to add
multiple frame types, and you have not defined
the board explicitly by using its port address."
$PCNTNW_9 = "I/O port address of the network device."
$PCNTNW_10 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 0200 - 03E0
in 20h steps
\nSupported values for EtherTeam PCI: 0000 - FFE0
in 20h steps"
$PCNTNW_11 = "IRQ number of the networking board"
$PCNTNW_12 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 3, 4, 5, 9, A, B, F
\nSupported values for EtherTeam PCI: 1 - F"
$PCNTNW_13 = "DMA channel of the networking board."
$PCNTNW_14 = "This option applies to EtherTeam ISA only.
Found by scan as default. If explicitly specified,
must match with its actual value."
$PCNTNW_15 = "Full Duplex Support."
$PCNTNW_16 = "Change the Default Full Duplex operation."
LANG: 7
;German
$PCNTNW_1 = "AMD PCnet Family (EtherTeam PCI/ISA) Network Driver"
$PCNTNW_2 = "This driver (PCNTNW.LAN) supports both EtherTeam ISA
and EtherTeam PCI network adapters."
$PCNTNW_3 = "Bus Type of the adapter installed."
$PCNTNW_4 = "As default, all bus types are scanned. If
explicitly specified, then only that bus
type is scanned."
$PCNTNW_7 = "Physical Board Number"
$PCNTNW_8 = "This keyword is applied only if you need to add
multiple frame types, and you have not defined
the board explicitly by using its port address."
$PCNTNW_9 = "I/O port address of the network device."
$PCNTNW_10 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 0200 - 03E0
in 20h steps
\nSupported values for EtherTeam PCI: 0000 - FFE0
in 20h steps"
$PCNTNW_11 = "IRQ number of the networking board"
$PCNTNW_12 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 3, 4, 5, 9, A, B, F
\nSupported values for EtherTeam PCI: 1 - F"
$PCNTNW_13 = "DMA channel of the networking board."
$PCNTNW_14 = "This option applies to EtherTeam ISA only.
Found by scan as default. If explicitly specified,
must match with its actual value."
$PCNTNW_15 = "Full Duplex Support."
$PCNTNW_16 = "Change the Default Full Duplex operation."
LANG: 8
;Italian
$PCNTNW_1 = "AMD PCnet Family (EtherTeam PCI/ISA) Network Driver"
$PCNTNW_2 = "This driver (PCNTNW.LAN) supports both EtherTeam ISA
and EtherTeam PCI network adapters."
$PCNTNW_3 = "Bus Type of the adapter installed."
$PCNTNW_4 = "As default, all bus types are scanned. If
explicitly specified, then only that bus
type is scanned."
$PCNTNW_7 = "Physical Board Number"
$PCNTNW_8 = "This keyword is applied only if you need to add
multiple frame types, and you have not defined
the board explicitly by using its port address."
$PCNTNW_9 = "I/O port address of the network device."
$PCNTNW_10 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 0200 - 03E0
in 20h steps
\nSupported values for EtherTeam PCI: 0000 - FFE0
in 20h steps"
$PCNTNW_11 = "IRQ number of the networking board"
$PCNTNW_12 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 3, 4, 5, 9, A, B, F
\nSupported values for EtherTeam PCI: 1 - F"
$PCNTNW_13 = "DMA channel of the networking board."
$PCNTNW_14 = "This option applies to EtherTeam ISA only.
Found by scan as default. If explicitly specified,
must match with its actual value."
$PCNTNW_15 = "Full Duplex Support."
$PCNTNW_16 = "Change the Default Full Duplex operation."
LANG: 14
;Spanish
$PCNTNW_1 = "AMD PCnet Family (EtherTeam PCI/ISA) Network Driver"
$PCNTNW_2 = "This driver (PCNTNW.LAN) supports both EtherTeam ISA
and EtherTeam PCI network adapters."
$PCNTNW_3 = "Bus Type of the adapter installed."
$PCNTNW_4 = "As default, all bus types are scanned. If
explicitly specified, then only that bus
type is scanned."
$PCNTNW_7 = "Physical Board Number"
$PCNTNW_8 = "This keyword is applied only if you need to add
multiple frame types, and you have not defined
the board explicitly by using its port address."
$PCNTNW_9 = "I/O port address of the network device."
$PCNTNW_10 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 0200 - 03E0
in 20h steps
\nSupported values for EtherTeam PCI: 0000 - FFE0
in 20h steps"
$PCNTNW_11 = "IRQ number of the networking board"
$PCNTNW_12 = "Found by scan as default. If explicitly specified,
must match with its actual value.
\nSupported values for EtherTeam ISA: 3, 4, 5, 9, A, B, F
\nSupported values for EtherTeam PCI: 1 - F"
$PCNTNW_13 = "DMA channel of the networking board."
$PCNTNW_14 = "This option applies to EtherTeam ISA only.
Found by scan as default. If explicitly specified,
must match with its actual value."
$PCNTNW_15 = "Full Duplex Support."
$PCNTNW_16 = "Change the Default Full Duplex operation."
