┌───────────────────────────────────────────────────────────────┐
│		  ACCTON TECHNOLOGY CORPORATION 		│
│	ETHERPOCKET LAN MANAGER DRIVER INSTALLATION GUIDE	│
│								│
│		     08/19/1993 VERSION 2.11			│
│								│
│	Copyright 1989-1993 ACCTON Technology Corporation	│
│		      All rights reserved.			│
└───────────────────────────────────────────────────────────────┘

The drivers contained in this diskette are for the following
ACCTON EtherPocket lan adapters:

	┌────────────────────────────────────────────┐
	│   Product Name	    Product Number   │
	├────────────────────────────────────────────┤
	│  EtherPocket-10T	       EN2201	     │
	│  EtherPocket-CX	       EN2202	     │
	│  EtherPocket-Duo	       EN2209	     │
	└────────────────────────────────────────────┘


They are used with 3Com 3+Open, Microsoft OS/2 LAN Manager OEM
distribution, Release 1.x or 2.x,  and	other  compatible  OEM
versions of LAN Manager.  The drivers named ETHPOCK conform to
the Network Driver Interface Specification (NDIS) defined by
Microsoft/3Com.



1. INSTALLATION PROCEDURE

  a. NDIS driver Installation Procedure

     1. Insert your copy of Pathway Drivers diskette into drive A. Enter as
       follow :

       C:\>A:

     2. To copy the software onto the system, enter :

       A:\> pwinstal C:

       where C: is the disk drive ( you could also use D:, E:, and so on )
       that you intend to use for the installation of your Pathway software
       on a hard drive system. The PWINSTAL program automatically installs
       the driver software in a new directory named \PATHWAY on the drive you
       specified.

       The diskette is finished copying when you receive the following
       message: "The Pathway Drivers have been copied successfully. Refer to
       documentation to complete driver installation."

     3. Insert this diskette to drive A: and copy NDIS driver to the
       subdirectory where you install the Pathway software :

       A:\> Copy A:\NDIS\ETHPOCK.DOS C:\PATHWAY

     4. Edit the C:\CONFIG.SYS file to contains the following three entries :

       DEVICE=C:\PATHWAY\PWTCP.SYS
       DEVICE=C:\PATHWAY\PROTMAN.EXE/I:C:\PATHWAY
       DEVICE=C:\PATHWAY\ETHPOCK.DOS

     5. Use any text editor to generate  a PROTOCOL.INI file in C:\PATHWAY
       which must have the following section

       [EN220x]
       DriverName = ETHPOCK$

     6. The startup batch file - autoexec.bat should have the following entries
       in the order shown :

       path=c:\pathway
       ndis [-d:#]
       pwbind

       where the -d option is used when accessing a specific module number
       within protocol.ini. In your protocol.ini file, a line enclosed by
       square brackets designates the beginning of a new module. Each module
       is referred to by a hexadecimal number. The first module is module
       number one. The second module is module two, and so on.

  b. Pathway Kernel Installation Procedure

     1. Insert your copy of Pathway Kernel diskette into drive A. Enter as
       follow :

       C:\>A:

     2. To copy the software onto the system, enter :

       A:\> pwinstal C:

       where C: is the disk drive ( you could also use D:, E:, and so on )
       that you intend to use for the installation of your Pathway software
       on a hard drive system. The PWINSTAL program automatically installs
       the driver software in a new directory named \PATHWAY on the drive you
       specified.

       Diskette copying is complete when you see the following message : "
       Pathway Kernel files have been copied successfully. Reboot and refer
       to the documentation to complete kernel installation. "

     3. Remove the diskette from drive A: and reboot your PC by pressing <Ctrl>,
       <Alt>, and <Del> at the same time.

     4. Change current directory to PATHWAY.

     5. Run the CUSTOM program in order to set or change the following settings:

       . The Internet address
       . The subnet bits ( if your network includes subnetworks )
       . The gateway address ( if you are communicating with hosts outside your
	 local network )

     6. Remove the diskette from drive A: and reboot your PC by pressing <Ctrl>,
       <Alt>, and <Del> at the same time.

     7. Enter the following command to load the Kernel :

       C:\PATHWAY> PWTCP

     8. Test your PC Using PING program

       C:\PATHWAY> PING hostname

       where hostname is the official name, alias, or Internet address of a
       host on your network that you expect to be able to communicate with.

     9. Now according to your application, you can install Character-based
-- THE END --