; Intel EtherExpress(TM) PRO/10 LAN Adapter
; Copyright 1994, 1995 Intel Corporation. All Rights Reserved.
;
; Date: 08/09/95
; Version: 1.03
; Filename: !INT1030.CFG
BOARD
ID = "INT1030"
NAME = "Intel EtherExpress(TM) PRO/10 LAN Adapter"
MFR = "INTEL"
CATEGORY = "NET"
SLOT= ISA8OR16
SKIRT = NO
READID = NO
IOCHECK = INVALID
DISABLE = SUPPORTED
COMMENTS = "\nIntel EtherExpress(TM) PRO/10 LAN Adapter Configuration File V1.03\n\n
The Intel EtherExpress(TM) PRO/10 LAN Adapter is an ISA adapter.
Use this file to select settings for the adapter and write them down.
Then run SOFTSET2 and configure the adapter with the settings you
chose."
HELP = "Press ENTER to review and configure these items:\n\n
\to I/O Address\n
\to Interrupt Request Number\n
\to Flash Memory Range"
SOFTWARE(1) ="Run SOFTSET2.EXE and configure this adapter with the
following settings:\n"
; INCLUDE="INT1030.OVL"
; BEGINOVL
FUNCTION = "I/O Address"
HELP = "I/O ADDRESS assigns a 16-byte block of input/output addresses
used to transfer data between the adapter and the computer.
Select an I/O address not used by any other device in the computer.
If two boards share the same I/O addresses, neither will work
correctly."
COMMENTS = "Select an I/O Address not used by other boards."
CHOICE="300-30F (Default)"
LINK
PORT=300h-30Fh
INIT=SOFTWARE(1) "\tI/O Address: 300"
CHOICE="200-20F"
LINK
PORT=200h-20Fh
INIT=SOFTWARE(1) "\tI/O Address: 200"
CHOICE="210-21F"
LINK
PORT=210h-21Fh
INIT=SOFTWARE(1) "\tI/O Address: 210"
CHOICE="220-22F"
LINK
PORT=220h-22Fh
INIT=SOFTWARE(1) "\tI/O Address: 220"
CHOICE="230-23F"
LINK
PORT=230h-23Fh
INIT=SOFTWARE(1) "\tI/O Address: 230"
CHOICE="240-24F"
LINK
PORT=240h-24Fh
INIT=SOFTWARE(1) "\tI/O Address: 240"
CHOICE="250-25F"
LINK
PORT=250h-25Fh
INIT=SOFTWARE(1) "\tI/O Address: 250"
CHOICE="260-26F"
LINK
PORT=260h-26Fh
INIT=SOFTWARE(1) "\tI/O Address: 260"
CHOICE="280-28F"
LINK
PORT=280h-28Fh
INIT=SOFTWARE(1) "\tI/O Address: 280"
CHOICE="290-29F"
LINK
PORT=290h-29Fh
INIT=SOFTWARE(1) "\tI/O Address: 290"
CHOICE="2A0-2AF"
LINK
PORT=2A0h-2AFh
INIT=SOFTWARE(1) "\tI/O Address: 2A0"
CHOICE="2B0-2BF"
LINK
PORT=2B0h-2BFh
INIT=SOFTWARE(1) "\tI/O Address: 2B0"
CHOICE="2C0-2CF"
LINK
PORT=2C0h-2CFh
INIT=SOFTWARE(1) "\tI/O Address: 2C0"
CHOICE="2D0-2DF"
LINK
PORT=2D0h-2DFh
INIT=SOFTWARE(1) "\tI/O Address: 2D0"
CHOICE="2E0-2EF"
LINK
PORT=2E0h-2EFh
INIT=SOFTWARE(1) "\tI/O Address: 2E0"
CHOICE="2F0-2FF"
LINK
PORT=2F0h-2FFh
INIT=SOFTWARE(1) "\tI/O Address: 2F0"
CHOICE="310-31F"
LINK
PORT=310h-31Fh
INIT=SOFTWARE(1) "\tI/O Address: 310"
CHOICE="320-32F"
LINK
PORT=320h-32Fh
INIT=SOFTWARE(1) "\tI/O Address: 320"
CHOICE="330-33F"
LINK
PORT=330h-33Fh
INIT=SOFTWARE(1) "\tI/O Address: 330"
CHOICE="340-34F"
LINK
PORT=340h-34Fh
INIT=SOFTWARE(1) "\tI/O Address: 340"
CHOICE="350-35F"
LINK
PORT=350h-35Fh
INIT=SOFTWARE(1) "\tI/O Address: 350"
CHOICE="360-36F"
LINK
PORT=360h-36Fh
INIT=SOFTWARE(1) "\tI/O Address: 360"
CHOICE="370-37F"
LINK
PORT=370h-37Fh
INIT=SOFTWARE(1) "\tI/O Address: 370"
CHOICE="380-38F"
LINK
PORT=380h-38Fh
INIT=SOFTWARE(1) "\tI/O Address: 380"
CHOICE="390-39F"
LINK
PORT=390h-39Fh
INIT=SOFTWARE(1) "\tI/O Address: 390"
FUNCTION = "Interrupt"
HELP = "INTERRUPT assigns the interrupt (IRQ) that the adapter uses to
request attention from the computer.
Select an IRQ not used by any other device in the computer.
If two boards share the same IRQ, neither will work correctly."
COMMENTS = "Select an interrupt not used by other boards."
CHOICE = "IRQ 5 (Default)"
LINK
IRQ = 5
SHARE = NO
INIT=SOFTWARE(1) "\tIRQ: 5"
CHOICE = "IRQ 3"
LINK
IRQ = 3
SHARE = NO
INIT=SOFTWARE(1) "\tIRQ: 3"
CHOICE = "IRQ 9"
LINK
IRQ = 9
SHARE = NO
INIT=SOFTWARE(1) "\tIRQ: 9"
CHOICE = "IRQ 10"
LINK
IRQ = 10
SHARE = NO
INIT=SOFTWARE(1) "\tIRQ: 10"
CHOICE = "IRQ 11"
LINK
IRQ = 11
SHARE = NO
INIT=SOFTWARE(1) "\tIRQ: 11"
FUNCTION = "Flash Chip Address"
HELP = "FLASH CHIP ADDRESS assigns a 16-Kbyte block of high memory to
the flash chip. The flash chip stores remote boot programs and
the FlashWorks utilities. If you don't plan to use a remote boot
program or the FlashWorks utilities, you can disable this option.
If you need to use a remote boot program, make sure to identify
the program in REMOTE BOOT PROGRAM in Softset2."
COMMENTS = "Select the memory address you want the flash chip to use. If you
aren't using flash memory, select FLASH MEMORY DISABLED."
CHOICE = "D0000-D3FFF (Default)"
COMBINE
MEMORY=16K
ADDRESS=0D0000H
WRITABLE=NO
MEMTYPE=OTH
SHARE=NO
SIZE=BYTE
CACHE=NO
DECODE=24
INIT=SOFTWARE(1) "\tFlash: D000"
CHOICE = "C8000-CBFFF"
COMBINE
MEMORY=16K
ADDRESS=0C8000H
WRITABLE=NO
MEMTYPE=OTH
SHARE=NO
SIZE=BYTE
CACHE=NO
DECODE=24
INIT=SOFTWARE(1) "\tFlash: C800"
CHOICE = "CC000-CFFFF"
COMBINE
MEMORY=16K
ADDRESS=0CC000H
WRITABLE=NO
MEMTYPE=OTH
SHARE=NO
SIZE=BYTE
CACHE=NO
DECODE=24
INIT=SOFTWARE(1) "\tFlash: CC00"
CHOICE = "D4000-D7FFF"
COMBINE
MEMORY=16K
ADDRESS=0D4000H
WRITABLE=NO
MEMTYPE=OTH
SHARE=NO
SIZE=BYTE
CACHE=NO
DECODE=24
INIT=SOFTWARE(1) "\tFlash: D400"
CHOICE = "D8000-DBFFF"
COMBINE
MEMORY=16K
ADDRESS=0D8000H
WRITABLE=NO
MEMTYPE=OTH
SHARE=NO
SIZE=BYTE
CACHE=NO
DECODE=24
INIT=SOFTWARE(1) "\tFlash: D800"
CHOICE = "DC000-DFFFF"
COMBINE
MEMORY=16K
ADDRESS=0DC000H
WRITABLE=NO
MEMTYPE=OTH
SHARE=NO
SIZE=BYTE
CACHE=NO
DECODE=24
INIT=SOFTWARE(1) "\tFlash: DC00"
CHOICE = "Flash Memory Disabled"
FREE
INIT=SOFTWARE(1) "\tFlash: Disabled"
; ENDOVL
