BOARD	 ; 11/09 fcm New, 12/13 fcm Chg, 5/24/91 iyw Rev., 01/10/92 tam rev.
 ID="TCM5030"
 NAME="3COM EtherLink II Family"
 MFR="3COM"
 CATEGORY="NET"
 SLOT=ISA8    
 LENGTH= 171
 COMMENTS="
 \nThe I/O base and shared memory base options on the Etherlink II adapter
 are set by jumpers. The interrupt level, DMA channel, data mode, and
 transceiver type are software programmable.
 \nNOTE: IRQ 2 is equivalent to IRQ 9. "

JUMPER(1)=5
 JTYPE=paired
 NAME="MEMORY"
 LABEL=LOC(5-1) "DISABLE" "DC000" "D8000" "CC000" "C8000"
 VERTICAL=YES
 COMMENTS="Only one setting can be selected at any given time for shared
 memory mode.
 \nRefer to EtherLink II Adapter Guide for details on the data transfer
 mode setting.\n"

JUMPER(2)=8
 JTYPE=paired
 NAME="I/O ADDR"
 LABEL=LOC(8-1) "300" "310" "330" "350" "250" "280" "2A0" "2E0"
 VERTICAL=YES
 COMMENTS="Make sure your software parameter setting matches the jumper
 setting.\n"

SOFTWARE(1) ="
 Different network operating systems provide different configuration formats.
 \n\nThe NetWare software installation utilities, SHGEN, WSGEN, NETGEN, and
 BRGEN, provide a predefined list of configuration settings to choose from.
 You can choose other settings using the JUMPER.EXE utility.\n
 \nLanManager lists all of the configuration options in the PROTOCOL.INI
 file.
 \n\nThe 3Plus network operating system uses device drivers which must be
 set in the CONFIG.SYS file: DEVICE=ETH503.SYS /I:x /A:y /D:z [/M...]
 \n\nMake sure you configure your software and EtherLink II adapter with
 the options:"

FUNCTION="3C503 Config Options"
TYPE="NET"

SUBFUNCTION="I/O Addresses"
  CHOICE="300-30F"
    LINK
    PORT=300h-30Fh
    INIT=JUMPER(2) LOC(8-1) 10000000
    INIT=SOFTWARE(1) "\tI/O=300"
  CHOICE="310-31F"
    LINK
    PORT=310h-31Fh
    INIT=JUMPER(2) LOC(8-1) 01000000
    INIT=SOFTWARE(1) "\tI/O=310"
  CHOICE="330-33F"
    LINK
    PORT=330h-33Fh
    INIT=JUMPER(2) LOC(8-1) 00100000
    INIT=SOFTWARE(1) "\tI/O=330"
  CHOICE="350-35F"
    LINK
    PORT=350h-35Fh
    INIT=JUMPER(2) LOC(8-1) 00010000
    INIT=SOFTWARE(1) "\tI/O=350"
  CHOICE="250-25F"
    LINK
    PORT=250h-25Fh
    INIT=JUMPER(2) LOC(8-1) 00001000
    INIT=SOFTWARE(1) "\tI/O=250"
  CHOICE="280-28F"
    LINK
    PORT=280h-28Fh
    INIT=JUMPER(2) LOC(8-1) 00000100
    INIT=SOFTWARE(1) "\tI/O=280"
  CHOICE="2A0-2AF"
    LINK
    PORT=2A0h-2AFh
    INIT=JUMPER(2) LOC(8-1) 00000010
    INIT=SOFTWARE(1) "\tI/O=2A0"
  CHOICE="2E0-2EF"
    LINK
    PORT=2E0h-2EFh
    INIT=JUMPER(2) LOC(8-1) 00000001
    INIT=SOFTWARE(1) "\tI/O=2E0"

SUBFUNCTION="Interrupt Level"
  CHOICE="IRQ 3"
    LINK
    IRQ=3
    INIT=SOFTWARE(1) "\tIRQ=3"
  CHOICE="IRQ 2"
    LINK
    IRQ=2
    INIT=SOFTWARE(1) "\tIRQ=2"
  CHOICE="IRQ 4"
    LINK
    IRQ=4
    INIT=SOFTWARE(1) "\tIRQ=4"
  CHOICE="IRQ 5"
    LINK
    IRQ=5
    INIT=SOFTWARE(1) "\tIRQ=5"

SUBFUNCTION="Boot PROM Not Installed"
  COMMENTS="
 Without the Boot PROM installed, the memory address jumper setting
 determines the default data transfer mode.  Shared memory mode is slightly
 faster than DMA or PIO modes.  The default may be overridden with the
 software parameters.\n"
  CHOICE="Shared Memory Enabled"
    COMBINE	     
    MEMORY=8K
    ADDRESS=0DC000h|0D8000h|0CC000h|0C8000h
    MEMTYPE=OTH
    INIT=JUMPER(1) LOC(5-1) 01000|00100|00010|00001
    INIT=SOFTWARE(1) "\tRAM=DC000"|"\tRAM=D8000"|"\tRAM=CC000"|"\tRAM=C8000"
  CHOICE="Shared Memory Disabled"
    LINK
    DMA=1|2|3
    TIMING=TYPEA
    INIT=JUMPER(1) LOC(5-1) 10000|10000|10000
    INIT=SOFTWARE(1) "\tDMA=1"|"\tDMA=2"|"\tDMA=3"

SUBFUNCTION="Boot PROM Installed"
  COMMENTS="
 If the Boot PROM is installed, the memory jumper setting determines
 the PROM location and the data transfer can only fall on the
 DMA or PIO mode.\n"
  CHOICE="Shared Memory Enabled"
    COMBINE	     
    MEMORY=8K
    ADDRESS=0DC000h|0D8000h|0CC000h|0C8000h
    MEMTYPE=OTH
    INIT=JUMPER(1) LOC(5-1) 01000|00100|00010|00001
    INIT=SOFTWARE(1) "\tROM=DC000"|"\tROM=D8000"|"\tROM=CC000"|"\tROM=C8000"
    LINK
    DMA = 1|2|3
    TIMING=TYPEA
    INIT=software(1) "\tDMA=1"|"\tDMA=2"|"\tDMA=3"

; %VER ELII EISA Configuration File for EDII v2.0c