;************************************************************************
;
;       UltraStor VESA VL-BUS MASTER Host Adapter (ULTRA 34FA)
;
;	UltraStor ULTRA 34FA EISA configuration file
;	Version: 1.00
;	Date   : June 25, 1993
;
;************************************************************************

;------------------------------------------------------------------------
;	Board Identification Block
;------------------------------------------------------------------------

BOARD
  ID = "USC0342"
  NAME = "UltraStor - ULTRA 34FA VESA VL-BUS Host Adapter" 
  MFR = "UltraStor"
  CATEGORY = "MSD"			;Mass Storage Device
  SLOT = ISA16				;For ISA-16 bit slot
  LENGTH = 210
  AMPERAGE = 800
  SKIRT = NO
  READID = NO

  COMMENTS = "ULTRA 34FA is a high performance SCSI host adapter interfacing
	the VL-VESA local bus supporting up to 7 SCSI devices. A high speed
	32 bit micro-processor provides the local intelligence for command
	processing.\n\n
	The ULTRA 34FA features:\n
	. VL-VESA Local Bus BUS Master data transfers.\n
	. MailBox Command Protocol, Command Chaining,\n
	  Command Queuing, and Scatter/Gather.\n
	. Coexits with other disk controllers / H/A in a system.\n
	. Easy controller configuration using software utility.\n
	. Device specific setup options.\n\n"


;------------------------------------------------------------------------
;	Initialization Information Block
;------------------------------------------------------------------------

;************  Jumper/Switch Configuration Statement Block  **************

JUMPER(1) = 1
	NAME = "JPTP"
	JTYPE = PAIRED
	VERTICAL = NO
	LABEL = LOC(1) "TermPower"
	INITVAL = LOC(1) x
	FACTORY = LOC(1) 1
	COMMENTS = "\tSCSI Terminator Power:\n\n
		    \tIN : ULTRA 34FA supplies power\n
		    \tOUT: Power supplied from SCSI pin 26\n"

JUMPER(2) = 2
	NAME = "JP2"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-2) "64 Bytes" "32 Bytes"
	INITVAL = LOC(1-2) xx
	FACTORY = LOC(1-2) 10
	COMMENTS =
		"\tData Transfer Burst Length Control:\n
		 \tLength           1-2     2-3\n
		 \t64 Bytes/Burst   IN      OUT\n
		 \t32 Bytes/Burst   OUT     IN\n"

SWITCH(1) = 8
	NAME = "S1"
	STYPE = DIP
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-8) "Flpy Ctrl" "BIOS ADDR1" "BIOS ADDR2" "BIOS ADDR3"
			 "I/O ADDR1" "I/O ADDR2" "I/O ADDR3" "ConfigCtrl"
	INITVAL = LOC(1-8) xxxxxxxx
	FACTORY = LOC(1-8) 11111111
	COMMENTS =
		"\tFloppy Control (SW1):\n
		 \tON : Software Controlled\n
		 \tOFF: Disable\n\n

		 \tBIOS Address:\n
		 \tAddress    SW2   SW3   SW4\n
		 \tDisable    ON    ON    ON\n\n

		 \tI/O Address:\n
		 \tAddress    SW5   SW6   SW7\n
		 \t 330H      ON    ON    ON\n\n

		 \tConfiguration Control (SW8):\n
		 \tON : BIOS and I/O addresses are controlled by software\n
		 \tOFF: BIOS and I/O address controller by S1 switch\n"

;***********************************************************************

GROUP = "UltraStor ULTRA 34FA Disk Controller"
TYPE = "MSD"

FUNCTION = "Host Adapter Options"
TYPE = "HDKCTL"

    SUBFUNCTION = "Floppy Control"
    COMMENTS = "Select Software control or Disable.\n"
	CHOICE = "Software"
	FREE
	INIT = SWITCH(1) LOC(1) 1

        CHOICE = "Disable" 
	FREE
	INIT = SWITCH(1) LOC(1) 0

    SUBFUNCTION = "BIOS Address Selection"
    COMMENTS = "Switch configuration is valid only with switch 8 in S1
		set to OFF.\n" 
        CHOICE = "Disable" 
	FREE
	INIT = SWITCH(1) LOC(2 3 4) 111

	CHOICE = "C4000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0C4000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 110

	CHOICE = "C8000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0C8000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 101

	CHOICE = "CC000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0CC000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 100

	CHOICE = "D0000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0D0000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 011

	CHOICE = "D4000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0D4000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 010

	CHOICE = "D8000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0D8000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 001

	CHOICE = "DC000h"
        FREE
	MEMORY = 16K
	ADDRESS = 0DC000h
	MEMTYPE = OTH
	WRITABLE = YES
	SHARE = NO
	SIZE = BYTE
	CACHE = YES
	INIT = SWITCH(1) LOC(2 3 4) 000

    SUBFUNCTION = "I/O Port Address Selection"
    COMMENTS = "Switch configuration is valid only with swich 8 in S1
		set to OFF.\n" 
	CHOICE = "330H"
	LINK
	PORT = 330h-33Fh
	INIT = SWITCH(1) LOC(5 6 7) 111

	CHOICE = "340H"
	LINK
	PORT = 340h-34Fh
	INIT = SWITCH(1) LOC(5 6 7) 110

	CHOICE = "310H"
	LINK
	PORT = 310h-31Fh
	INIT = SWITCH(1) LOC(5 6 7) 101

	CHOICE = "230H"
	LINK
	PORT = 230h-23Fh
	INIT = SWITCH(1) LOC(5 6 7) 100

	CHOICE = "240H"
	LINK
	PORT = 240h-24Fh
	INIT = SWITCH(1) LOC(5 6 7) 011

	CHOICE = "210H"
	LINK
	PORT = 210h-21Fh
	INIT = SWITCH(1) LOC(5 6 7) 010

	CHOICE = "130H"
	LINK
	PORT = 130h-13Fh
	INIT = SWITCH(1) LOC(5 6 7) 001

	CHOICE = "140H"
	LINK
	PORT = 140h-14Fh
	INIT = SWITCH(1) LOC(5 6 7) 000

    SUBFUNCTION = "Configuration Control Selection"
    COMMENTS = "This switch selects board configuration to be controlled
		by switch or software.\n" 
	CHOICE = "Software"
	FREE
	INIT = SWITCH(1) LOC(8) 1

	CHOICE = "Switch"
	FREE
	INIT = SWITCH(1) LOC(8) 0

ENDGROUP;