;************************************************************************
;
; UltraStor ISA SCSI Host Adapter (ULTRA 14FB)
;
; UltraStor ULTRA 14FB EISA configuration file
; Version: 1.00
; Date : May 11, 1993
;
;************************************************************************
;------------------------------------------------------------------------
; Board Identification Block
;------------------------------------------------------------------------
BOARD
ID = "USC0142"
NAME = "UltraStor - ULTRA 14FB ISA SCSI Host Adapter"
MFR = "UltraStor"
CATEGORY = "MSD" ;Mass Storage Device
SLOT = ISA16 ;For ISA-16 bit slot
LENGTH = 210
AMPERAGE = 800
SKIRT = NO
READID = NO
COMMENTS = "ULTRA 14FB is a high performance ISA SCSI host adapter
supporting up to 7 SCSI devices. A high speed 8 bit micro-processor
provides the local intelligence for command processing.\n\n
The ULTRA 14FB features:\n
. ISA BUS master burst transfer rate of up to 10MB/sec.\n
. MailBox Command/Status Protocol for Multi-Threaded
Command Chaining and Queuing, and Scatter/Gather.\n
. Coexits with other disk controllers / H/A in a system.\n
. Easy controller configuration using software utility.\n
. Device specific setup options.\n\n"
;------------------------------------------------------------------------
; Initialization Information Block
;------------------------------------------------------------------------
;************** Jumper Configuration Statement Block ******************
JUMPER(2) = 1
NAME = "JP2"
JTYPE = PAIRED
VERTICAL = YES
REVERSE = YES
INITVAL = LOC(1) x
FACTORY = LOC(1) 1
LABEL = LOC(1) "FLOPPY"
COMMENTS = "\tFloppy Controller:\n\n
\tEnable : Jumper in\n
\tDisable : Jumper out\n"
JUMPER(11) = 3
NAME = "JP11"
JTYPE = PAIRED
VERTICAL = NO
REVERSE = YES
INITVAL = LOC(1-3) xxx
FACTORY = LOC(1-3) 010
LABEL = LOC(1-3) "BIOS ADDR1" "BIOS ADDR2" "BIOS ADDR3"
COMMENTS =
"\tBIOS Address Setting:\n
\tAddress 1-2 3-4 5-6\n
\tDisable OUT OUT OUT\n
\tC4000 OUT OUT IN\n
\tC8000 OUT IN OUT\n
\tCC000 OUT IN IN\n
\tD0000 IN OUT OUT\n
\tD4000 IN OUT IN\n
\tD8000 IN IN OUT\n
\tDC000 IN IN IN\n"
JUMPER(12) = 4
NAME = "JP12"
JTYPE = PAIRED
VERTICAL = NO
REVERSE = YES
LABEL = LOC(1-4) "I/O ADDR1" "I/O ADDR2" "I/O ADDR3" "ConfigCtrl"
INITVAL = LOC(1-4) xxxx
FACTORY = LOC(1-4) 0000
COMMENTS =
"\tMailBox Port I/O Address:\n
\t Address 1-2 3-4 5-6\n
\t 330H OUT OUT OUT\n
\t 340H OUT OUT IN\n
\t 310H OUT IN OUT\n
\t 230H OUT IN IN\n
\t 240H IN OUT OUT\n
\t 210H IN OUT IN\n
\t 130H IN IN OUT\n
\t 140H IN IN IN\n\n
\tConfiguration Control:\n
\t OUT : BIOS and I/O addresses are controlled by software\n
\t IN : BIOS address controller by JP11 pins 1-2 3-4 5-6\n
\t I/O address controller by JP12 pins 1-2 3-4 5-6\n"
;***********************************************************************
GROUP = "UltraStor ULTRA 14FB Disk Controller"
TYPE = "MSD"
FUNCTION = "Host Adapter Options"
TYPE = "HDKCTL"
SUBFUNCTION = "BIOS Address Selection"
COMMENTS = "Jumper configuration is valid only with jumper JP12
pins 7-8 jumpered.\n"
CHOICE = "C8000h"
FREE
MEMORY = 16K
ADDRESS = 0C8000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 010
CHOICE = "C4000h"
FREE
MEMORY = 16K
ADDRESS = 0C4000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 001
CHOICE = "CC000h"
FREE
MEMORY = 16K
ADDRESS = 0CC000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 011
CHOICE = "D0000h"
FREE
MEMORY = 16K
ADDRESS = 0D0000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 100
CHOICE = "D4000h"
FREE
MEMORY = 16K
ADDRESS = 0D4000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 101
CHOICE = "D8000h"
FREE
MEMORY = 16K
ADDRESS = 0D8000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 110
CHOICE = "DC000h"
FREE
MEMORY = 16K
ADDRESS = 0DC000h
MEMTYPE = OTH
WRITABLE = YES
SHARE = NO
SIZE = BYTE
CACHE = YES
INIT = JUMPER(11) LOC(1 2 3) 111
CHOICE = "Disable"
FREE
INIT = JUMPER(11) LOC (1 2 3) 000
SUBFUNCTION = "I/O Port Address Selection"
COMMENTS = "Jumper configuration is valid only with jumper JP12
pins 7-8 jumpered.\n"
CHOICE = "330H"
LINK
PORT = 330h-33Fh
INIT = JUMPER(12) LOC(1 2 3) 000
CHOICE = "340H"
LINK
PORT = 340h-34Fh
INIT = JUMPER(12) LOC(1 2 3) 001
CHOICE = "310H"
LINK
PORT = 310h-31Fh
INIT = JUMPER(12) LOC(1 2 3) 010
CHOICE = "230H"
LINK
PORT = 230h-23Fh
INIT = JUMPER(12) LOC(1 2 3) 011
CHOICE = "240H"
LINK
PORT = 240h-24Fh
INIT = JUMPER(12) LOC(1 2 3) 100
CHOICE = "210H"
LINK
PORT = 210h-21Fh
INIT = JUMPER(12) LOC(1 2 3) 101
CHOICE = "130H"
LINK
PORT = 130h-13Fh
INIT = JUMPER(12) LOC(1 2 3) 110
CHOICE = "140H"
LINK
PORT = 140h-14Fh
INIT = JUMPER(12) LOC(1 2 3) 111
SUBFUNCTION = "Configuration Control Selection"
COMMENTS = "This jumper selects board configuration to be controlled
by jumper or software.\n"
CHOICE = "Software"
FREE
INIT = JUMPER(12) LOC(4) 0
CHOICE = "Jumper"
FREE
INIT = JUMPER(12) LOC(4) 1
FUNCTION = "Floppy Disk Option"
TYPE = "FDKCTL"
SUBFUNCTION = "Floppy Enable / Disable"
COMMENTS = "Enable or disable floppy drive controller.\n"
CHOICE = "Enable"
COMBINE
IRQ = 6
SHARE = NO
TRIGGER = EDGE
PORT = 03F0h-03F7h
SIZE = BYTE
INIT = JUMPER(2) LOC(1) 1
CHOICE = "Disable"
FREE
INIT = JUMPER(2) LOC(1) 0
ENDGROUP;
