< Installing the NetWare V4.xx drivers>

The following explains major installation procedures for V4.00/4.01/4.02/4.10:
After seeing a message block showing "Choose the server Drivers - Disk Driver"
during the installation, you'll find a list of default supported drivers.
Press <Ins> key to install an unlisted driver, i.e., NV4XXBMP.DSK for dc-390,
from drive A:.
Press <F3> key to specify the path: >A:\NETWARE.4XX. Select the NV4XXBMP.DSK
and press the <Enter> for loading this driver.
The system will then require you to do some other server driver installation.
After that the screen would show messages like the following:

  LOAD C:\NWSERVER\NV4XXBMP.DSK
  Loading module NV4XXBMP.DSK
    DC-390 PCI SCSI Adapter Driver For NetWare V4.00/4.01/4.02/4.10
    Version 1.51    April 24, 1995
    Auto-loading module ASPITRAN.DSK
    Tekram SCSI Adapter NetWare 386 ASPI Transport Layer
    Version 1.51    April 24, 1995
  Supported Slot values are 12
  Slot = 12 (note: this slot number is SLOT and MAINBOARD dependent)

Write down this slot number for later use and press <Enter> to proceed. After
some other operations on the installation the console screen will then display
the message "Edit File As Necessary: STARTUP.NCF" and require you to do further
editing:

  load NV4XXBMP.DSK port=E800 int=A
  load ASPICD.DSK int=0 int1=0 dma=0 dma1=0
    Modify to =>
  load NV4XXBMP.DSK SLOT=12	  (note: use the slot number you just wrote
					 down)
  load ASPICD.DSK int=0 int1=0 dma=0 dma1=0

In case that two or more DC-390s are present, you have to load the same driver
by typing "load NV4XXBMP" as many times as the number of DC-390 adapters
installed.
For example, to add another DC-390 we'll have to run the "load
C:\NWSERVER\NV4XXBMP.DSK" command at the system console prompt one more time.
And the screen may then show message like this:
  Loading module NV4XXBMP.DSK
    DC-390 PCI SCSI Adapter Driver For NetWare V4.00/4.01/4.02/4.10
    Version 1.51    April 24, 1995
    Auto-loading module ASPITRAN.DSK
    Tekram SCSI Adapter NetWare 386 ASPI Transport Layer
    Version 1.51    April 24, 1995
  Supported Slot values are 11
  Slot = 11

Write down this slot number just like you did for installing the first DC-390
and press <Enter> to proceed:

    DC-390: BUS#00 DEV#0B FUN#0
    Adapter SCSI ID : 7
    I/O Port Address: E800h
    Interrupt Level : 10

Then go on to edit STARTUP.NCF file by modifying the lines:
  load NV4XXBMP.DSK port=E800 int=A
  load ASPICD.DSK int=0 int1=0 dma=0 dma1=0
  load NV4XXBMP.DSK port=E400 int=A
    to =>
  load NV4XXBMP.DSK SLOT=12	  (note: 12 is the slot number for the first
					 DC-390)
  load ASPICD.DSK int=0 int1=0 dma=0 dma1=0
  load NV4XXBMP.DSK SLOT=11	  (note: 11 is the slot number for the second DC-390)