┌────────────────────────────────┐
│ Hard Disk Tech Specs(tm) v3.0 │
└────────────────────────────────┘
Hard Drive Solutions Family(tm)
//TMC-7000FASST2
01
D88, 82, 95, 82
D95, 82, 95, 60
D95, 60, 88, 60
D88, 60, 88, 82
T95, 72, 0, 1, J1
C83, 80, 1, 1
T82, 83, 0, 1, J2
C40, 92, 1, 0
T45, 91, 0, 1, J3
T5, 91, 0, 1, J4
T82, 83, 0, 4, Term Term
T12, 75, 0, 4, Spare Fuse
T85, 92, 0, 1, F1
T45, 60, 0, 1, W2
T63, 60, 0, 1, W3 W1 W4
T78, 73, 0, 1, W5
T61, 79, 0, 1, W6 W9
T77, 61, 0, 1, W98
T26, 81, 0, 1, W200 W201
{
Drives: 7 SCSI devices supported.
2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 Floppy connector.
J4 LED connector.
F1 Fuse (a spare is located on board).
W1 -1 Closed Floppy IRQ 3.
-2 Closed Floppy IRQ 4.
-3 Closed Floppy IRQ 5.
-4 Closed Floppy IRQ 7.
-5 Closed Floppy IRQ 9.
W2 -1 Open DMA channel 5.
-2 Open
-3 Closed
-4 Open
-5 Open
-6 Closed
Open (Default) DMA channel 6.
Closed
Open
Open
Closed
Open
Closed DMA channel 7.
Open
Open
Closed
Open
Open
-7 Closed HD IRQ 10.
-8 Closed HD IRQ 11.
-9 Closed HD IRQ 12.
-10 Closed HD IEQ 14.
-11 Closed (Default) HD IRQ 15.
W3 12345 (X - installed).
||||| (o - not installed).
oXXXX I/O port 308.
XoXXX I/O port 310.
ooXXX I/O port 318.
XXoXX I/O port 320.
oXoXX I/O port 328.
XooXX I/O port 330.
oooXX I/O port 338.
XXXoX I/O port 340.
oXXoX I/O port 348.
XoXoX (Default) I/O port 350.
ooXoX I/O port 358.
XXooX I/O port 360.
oXooX I/O port 368.
XoooX I/O port 370.
ooooX I/O port 378.
XXXXo I/O port 380.
oXXXo I/O port 388.
XoXXo I/O port 390.
ooXXo I/O port 398.
XXoXo I/O port 3A0.
oXoXo I/O port 3A8.
XooXo I/O port 3B0.
oooXo I/O port 3B8.
XXXoo I/O port 3C0.
oXXoo I/O port 3C8.
XoXoo I/O port 3D0.
ooXoo I/O port 3D8.
XXooo I/O port 3E0.
oXooo I/O port 3E8.
Xoooo I/O port 3F0.
W4 1234 (X - installed).
|||| (o - not installed).
XXoX BIOS address C:8000.
oXoX BIOS address C:A000.
XooX BIOS address C:C000.
oooX (Default) BIOS address C:E000.
XXXo BIOS address D:0000.
oXXo BIOS address D:2000.
XoXo BIOS address D:4000.
ooXo BIOS address D:6000.
XXoo BIOS address D:8000.
oXoo BIOS address D:A000.
Xooo BIOS address D:C000.
W5 Open Termination power disabled.
Closed Termination power enabled.
W6 Closed No floppy cable connected.
W9 Closed
Open Floppy cable present.
Open
W98 Open BIOS disabled.
Closed BIOS enabled (you MUST install this jumper unless this
board is the second TMC-7000FASST2 in the system).
W200 1-2 1st floppy is standard AT-type.
2-3 1st floppy is high-speed PS/2-type.
W201 1-2 2nd floppy is standard AT-type.
2-3 2nd floppy is high-speed PS/2-type.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-7000EX
03
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C60, 91, 1, 0
T65, 89, 0, 1, J2
T75, 66, 0, 1, LED
T75, 60, 0, 1, W4
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
LED Terminator LED (when on, this LED indicates
proper termination).
W4 Open Termination power disabled.
Closed Termination power enabled.
Note: This EISA adapter supports 32-bit, 1st-party Bus Master
data xfers. All configuration is accomplished via software.
The exception to this is terminator power (see W4).
}
*
//MCS-350
32
C80, 85, 1, 1
T80, 88, 0, 1, J1
T75, 66, 0, 1, W1
{
Drives: 7 SCSI devices supported.
J1 Internal SCSI connector.
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
Note: All other settings are configured via the PS/2 reference
disk.
}
*
//MCS-700
32
D88, 84, 95, 84
D95, 84, 95, 64
D95, 64, 88, 64
D88, 64, 88, 84
T95, 74, 0, 1, J1
C67, 91, 1, 0
T73, 89, 0, 1, J2
T30, 80, 0, 1, J3
T50, 88, 0, 1, F1 W1
T66, 85, 0, 1, Term. Term.
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector (SCSI-2 compatible).
J2 Internal SCSI connector (SCSI-1 compatible).
J3 DC power connector.
F1 Thermal fuse.
W1 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
Note: All other settings are configured via the PS/2 reference
disk.
}
*
//TMC-830
10
D62, 82, 75, 82
D75, 82, 75, 60
D75, 60, 62, 60
D62, 60, 62, 82
T75, 72, 0, 1, J1
C55, 80, 1, 1
T54, 83, 0, 1, J2
T55, 94, 0, 1, Terminator
T55, 91, 0, 1, Terminator
T55, 88, 0, 1, Terminator
T25, 91, 0, 1, W1 W2
T36, 55, 0, 1, W3 W4
T50, 55, 0, 1, W5
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W3 Open (Default) IRQ 5.
W4 Closed
Closed IRQ 3.
Open
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-840
10
D62, 82, 75, 82
D75, 82, 75, 60
D75, 60, 62, 60
D62, 60, 62, 82
T75, 72, 0, 1, J1
C35, 93, 1, 0
T40, 91, 0, 1, J2
T25, 85, 0, 1, Terminator Terminator Terminator
T46, 62, 0, 1, W1 W2
T36, 55, 0, 1, W3 W4
T22, 59, 0, 1, W6
T22, 56, 0, 1, W7
T21, 91, 0, 1, J3
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W3 Open (Default) IRQ 5.
W4 Closed
Closed IRQ 3.
Open
W6 Closed (Default) Short time-out delay.
W7 Open
Open Long time-out delay.
Closed
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-845
10
D62, 82, 75, 82
D75, 82, 75, 60
D75, 60, 62, 60
D62, 60, 62, 82
T75, 72, 0, 1, J1
C35, 93, 1, 0
T40, 91, 0, 1, J2
T21, 91, 0, 1, J3
T25, 85, 0, 1, Terminator Terminator Terminator
T46, 66, 0, 1, W1 W2
T36, 55, 0, 1, W3 W4
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W3 Open (Default) IRQ 5.
W4 Closed
Closed IRQ 3.
Open
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-850M
20
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C59, 93, 1, 0
T64, 91, 0, 1, J2
T54, 85, 0, 1, Terminator Terminator
T21, 91, 0, 1, F1
T63, 62, 0, 1, W1 W2 W3 W5
T17, 88, 0, 1, W4
T56, 66, 0, 1, W6 W7
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
F1 Thermal fuse.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
W3 1-2 Closed
3-4 Closed
Open BIOS address C:8000 - C:9FFF.
Closed
1-2 Closed
3-4 Closed
Closed BIOS address C:E000 - C:FFFF.
Open
1-2 Closed
3-4 Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
1-2 Closed
3-4 Closed
Open Extended BIOS address E:8000 - E:9FFF.
Open
1-3 Closed
2-4 Closed
Closed Extended BIOS address E:C000 - E:FFFF.
Open
1-3 Closed
2-4 Closed
W4 Open Termination power disabled.
Closed Termination power enabled.
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
W6 1-2 Closed (Default) IRQ 3.
W7 2-3 Closed IRQ 5.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-860
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C60, 93, 1, 0
T65, 91, 0, 1, J2
T15, 86, 0, 1, J3
T57, 85, 0, 1, Term. Term. Term.
T69, 62, 0, 1, W1 W2
T46, 55, 0, 1, W4
T75, 55, 0, 1, W5
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W4 -1 IRQ 3.
-2 IRQ 4.
-3 (Default) IRQ 5.
-4 IRQ 10.
-5 IRQ 11.
-6 IRQ 12.
-7 IRQ 14.
-8 IRQ 15.
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-860M
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C59, 93, 1, 0
T64, 91, 0, 1, J2
T16, 82, 0, 1, J8
T54, 85, 0, 1, Terminator Terminator
T44, 86, 0, 1, F1
T63, 62, 0, 1, W1 W2 W3 W5
T44, 91, 0, 1, W4
T69, 55, 0, 1, W7
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J8 LED connector.
F1 Thermal fuse.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
W3 1-2 Closed
3-4 Closed
Open BIOS address C:8000 - C:9FFF.
Closed
1-2 Closed
3-4 Closed
Closed BIOS address C:E000 - C:FFFF.
Open
1-2 Closed
3-4 Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
1-2 Closed
3-4 Closed
Open Extended BIOS address E:8000 - E:9FFF.
Open
1-3 Closed
2-4 Closed
Closed Extended BIOS address E:C000 - E:FFFF.
Open
1-3 Closed
2-4 Closed
W4 Open Termination power disabled.
Closed Termination power enabled.
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
W7 1-2 Closed (Default) IRQ 3.
3-4 Closed IRQ 4.
5-6 Closed IRQ 5.
7-8 Closed IRQ 10.
9-10 Closed IRQ 11.
11-12 Closed IRQ 12.
13-14 Closed IRQ 14.
15-16 Closed IRQ 15.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-870
00
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C75, 80, 1, 1
T74, 83, 0, 1, J2
C47, 88, 1, 1
T46, 92, 0, 1, J3
C40, 88, 1, 1
T39, 92, 0, 1, J4
T5, 85, 0, 1, J5
T22, 55, 0, 1, E1 E2
T56, 83, 0, 2, E3 E4
T58, 83, 0, 2, E5 E6
T70, 55, 0, 1, E7 E8
T62, 88, 0, 1, DIP SWITCH
{
Drives: 7 SCSI devices supported.
4 floppy drives (360KB, 720KB, 1.2MB, or 1.44MB).
Note: The first two floppies are controlled directly
by the host computer's BIOS, so support for
various drive capacities depends upon the
capabilities of your system. Also, you must
obtain and install a special driver in order
to access the last two floppy drives (the
capacities of which are determined by that
particular device driver).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 Primary floppy connector.
J4 Secondary floppy connector.
J5 LED connector.
E1-E2 Open (Default) Primary I/O ports.
Closed Secondary I/O port.
E3-E4 Open (Default) BIOS address C:A000 - C:BFFF.
E5-E6 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
E7-E8 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
Note: The following settings for the 8-position dip switch apply only
to v4.1E of the controller's BIOS. For v6.0x, all switches
should be in the 'OFF' position.
S1 Off Floppy drive 0 is 360KB.
On Floppy drive 0 is 1.2MB.
S2 Off Floppy drive 1 is 360KB.
On Floppy drive 1 is 1.2MB.
S3 Off Floppy drives 2 & 3 are 360KB
(both drives must be the same type).
On Floppy drives 2 & 3 are 1.2MB
(both drives must be the same type).
S4 Off No SCSI devices attached.
On (Default) 1 or more SCSI devices attached.
S5 Off Auto-detect number of floppy drives.
S6 Off
S7 Off
On 1 floppy installed.
Off
Off
Off 2 floppies installed.
On
Off
On 3 floppies installed.
On
Off
Off 4 floppies installed.
Off
On
}
*
//TMC-875
00
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C60, 93, 1, 0
T65, 91, 0, 1, J2
C30, 93, 1, 0
T35, 91, 0, 1, J3
C10, 93, 1, 0
T15, 91, 0, 1, J4
T5, 86, 0, 1, J5
T57, 85, 0, 1, Term. Term. Term.
T37, 75, 0, 1, F1 F2
T69, 62, 0, 1, W1 W2
T42, 55, 0, 1, W3 W4
{
Drives: 7 SCSI devices supported.
2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 Primary floppy connector.
J4 Secondary floppy connector.
J5 LED connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W3 Closed (Default) IRQ 3.
W4 Open
Open IRQ 5.
Closed
F1 Open (Default) Floppy I/O ports 3F2, 3F4, 3F5, 3F7.
Floppy DMA channel 2, IRQ 6.
Closed (Default) Floppy I/O ports 372, 374, 375, 377.
Floppy DMA channel 3, IRQ 5.
F2 Open (Default) No AT hard disk present.
Closed AT hard disk present.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-880
01
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C55, 93, 1, 0
T60, 91, 0, 1, J2
C40, 87, 1, 1
T39, 91, 0, 1, J3
T5, 91, 0, 1, J4
T45, 85, 0, 1, Terminator Terminator Terminator
T22, 86, 0, 1, F1 F2
T71, 62, 0, 1, W1 W2
T46, 55, 0, 1, W4
T55, 61, 0, 1, W6 W7
{
Drives: 7 SCSI devices supported.
2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 Floppy connector.
J4 LED connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W4 -1 IRQ 3.
-2 IRQ 4.
-3 (Default) IRQ 5.
-4 IRQ 10.
-5 IRQ 11.
-6 IRQ 12.
-7 IRQ 14.
-8 IRQ 15.
W6 Closed (Default) Short time-out delay.
W7 Open
Open Long time-out delay.
Closed
F1 Open (Default) Floppy I/O ports 3F2, 3F4, 3F5, 3F7.
Floppy DMA channel 2, IRQ 6.
Closed (Default) Floppy I/O ports 372, 374, 375, 377.
Floppy DMA channel 3, IRQ 5.
F2 Open (Default) No AT hard disk present.
Closed AT hard disk present.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-885
01
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C60, 93, 1, 0
T65, 91, 0, 1, J2
C30, 93, 1, 0
T35, 91, 0, 1, J3
C10, 93, 1, 0
T15, 91, 0, 1, J4
T5, 86, 0, 1, J5
T57, 85, 0, 1, Term. Term. Term.
T43, 65, 0, 1, F1 F2
T69, 62, 0, 1, W1 W2
T46, 55, 0, 1, W4
T75, 55, 0, 1, W5
{
Drives: 7 SCSI devices supported.
2 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 Primary floppy connector.
J4 Secondary floppy connector.
J5 LED connector.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
Open BIOS address C:8000 - C:9FFF.
Closed
Closed BIOS address C:E000 - C:FFFF.
Open
Closed BIOS address D:E000 - D:FFFF.
Closed
W4 -1 IRQ 3.
-2 IRQ 4.
-3 (Default) IRQ 5.
-4 IRQ 10.
-5 IRQ 11.
-6 IRQ 12.
-7 IRQ 14.
-8 IRQ 15.
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
F1 Open (Default) Floppy I/O ports 3F2, 3F4, 3F5, 3F7.
Floppy DMA channel 2, IRQ 6.
Closed (Default) Floppy I/O ports 372, 374, 375, 377.
Floppy DMA channel 3, IRQ 5.
F2 Open (Default) No AT hard disk present.
Closed AT hard disk present.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-885M
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C59, 93, 1, 0
T64, 91, 0, 1, J2
C19, 93, 1, 0
T24, 91, 0, 1, J3
T16, 82, 0, 1, J8
T54, 85, 0, 1, Terminator Terminator
T44, 86, 0, 1, F1
T63, 62, 0, 1, W1 W2 W3 W5
T44, 91, 0, 1, W4
T56, 72, 0, 1, W6
T69, 55, 0, 1, W7
{
Drives: 7 SCSI devices supported.
2 floppy drives (360KB, 720KB, 1.2MB, or 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 Floppy connector.
J8 LED connector.
F1 Thermal fuse.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
W3 1-2 Closed
3-4 Closed
Open BIOS address C:8000 - C:9FFF.
Closed
1-2 Closed
3-4 Closed
Closed BIOS address C:E000 - C:FFFF.
Open
1-2 Closed
3-4 Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
1-2 Closed
3-4 Closed
Open Extended BIOS address E:8000 - E:9FFF.
Open
1-3 Closed
2-4 Closed
Closed Extended BIOS address E:C000 - E:FFFF.
Open
1-3 Closed
2-4 Closed
W4 Open Termination power disabled.
Closed Termination power enabled.
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
W6 1-2 Closed (Default) Floppy controller enabled.
3-4 Closed
5-6 Closed
1-2 Open Floppy controller disabled.
3-4 Open
5-6 Open
W7 1-2 Closed (Default) IRQ 3.
3-4 Closed IRQ 4.
5-6 Closed IRQ 5.
7-8 Closed IRQ 10.
9-10 Closed IRQ 11.
11-12 Closed IRQ 12.
13-14 Closed IRQ 14.
15-16 Closed IRQ 15.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-850M
20
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C59, 93, 1, 0
T64, 91, 0, 1, J2
T54, 85, 0, 1, Terminator Terminator
T21, 91, 0, 1, F1
T63, 62, 0, 1, W1 W2 W3 W5
T17, 88, 0, 1, W4
T56, 66, 0, 1, W6 W7
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
F1 Thermal fuse.
W1 Open (Default) BIOS address C:A000 - C:BFFF.
W2 Open
W3 1-2 Closed
3-4 Closed
Open BIOS address C:8000 - C:9FFF.
Closed
1-2 Closed
3-4 Closed
Closed BIOS address C:E000 - C:FFFF.
Open
1-2 Closed
3-4 Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
1-2 Closed
3-4 Closed
Open Extended BIOS address E:8000 - E:9FFF.
Open
1-3 Closed
2-4 Closed
Closed Extended BIOS address E:C000 - E:FFFF.
Open
1-3 Closed
2-4 Closed
W4 Open Termination power disabled.
Closed Termination power enabled.
W5 Open (Default) Zero wait state disabled.
Closed Zero wait state enabled.
W6 1-2 Closed (Default) IRQ 3.
W7 2-3 Closed IRQ 5.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-1650
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C61, 93, 1, 0
T66, 91, 0, 1, J2
T16, 76, 0, 1, J3
T55, 85, 0, 1, Terminator Terminator
T50, 84, 0, 1, F1
T46, 81, 0, 1, W4
T73, 55, 0, 1, W1
T60, 66, 0, 1, W2
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
F1 Thermal fuse.
W1 -1 Open IRQ 3.
-2 Open
-3 Open
-1 Closed (Default) IRQ 5.
-2 Open
-3 Open
-1 Open IRQ 10.
-2 Closed
-3 Open
-1 Closed IRQ 11.
-2 Closed
-3 Open
-1 Open IRQ 12.
-2 Open
-3 Closed
-1 Closed IRQ 14.
-2 Open
-3 Closed
-1 Open IRQ 15.
-2 Closed
-3 Closed
W1 -4 Open I/O ports 140 - 14F.
-5 Open
Closed I/O ports 150 - 15F.
Open
Open I/O ports 160 - 16F.
Closed
Closed (Default) I/O ports 170 - 17F.
Closed
W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF.
-7 Open
Open BIOS address C:8000 - C:9FFF.
Open
Open BIOS address C:E000 - C:FFFF.
Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
W2 -1 Closed (Default) BIOS enabled.
-2 Closed
Open BIOS disabled.
Open
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-1660-solder
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C61, 93, 1, 0
T66, 91, 0, 1, J2
T16, 78, 0, 1, J3
T58, 85, 0, 1, Term. W3 Term.
T38, 91, 0, 1, F1
T46, 91, 0, 1, W4
T73, 55, 0, 1, W1
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
F1 Thermal fuse.
W1 -1 Open IRQ 3.
-2 Open
-3 Open
-1 Closed (Default) IRQ 5.
-2 Open
-3 Open
-1 Open IRQ 10.
-2 Closed
-3 Open
-1 Closed IRQ 11.
-2 Closed
-3 Open
-1 Open IRQ 12.
-2 Open
-3 Closed
-1 Closed IRQ 14.
-2 Open
-3 Closed
-1 Open IRQ 15.
-2 Closed
-3 Closed
W1 -4 Open (Default) I/O ports 140 - 14F.
-5 Open
Closed I/O ports 150 - 15F.
Open
Open I/O ports 160 - 16F.
Closed
Closed I/O ports 170 - 17F.
Closed
W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF.
-7 Open
Open BIOS address C:8000 - C:9FFF.
Open
Open BIOS address C:E000 - C:FFFF.
Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
W3 All Reserved.
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-1660-surface
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C61, 93, 1, 0
T66, 91, 0, 1, J2
T16, 78, 0, 1, J3
T16, 55, 0, 1, J4
T57, 85, 0, 1, Terminator Terminator
T44, 91, 0, 1, F1
T48, 86, 0, 1, W4
T73, 55, 0, 1, W1
T52, 60, 0, 1, W2
{
Drives: 7 SCSI devices supported.
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
J4 DC power connector.
F1 Thermal fuse.
W1 -1 Open IRQ 3.
-2 Open
-3 Open
-1 Closed (Default) IRQ 5.
-2 Open
-3 Open
-1 Open IRQ 10.
-2 Closed
-3 Open
-1 Closed IRQ 11.
-2 Closed
-3 Open
-1 Open IRQ 12.
-2 Open
-3 Closed
-1 Closed IRQ 14.
-2 Open
-3 Closed
-1 Open IRQ 15.
-2 Closed
-3 Closed
W1 -4 Open (Default) I/O ports 140 - 14F.
-5 Open
Closed I/O ports 150 - 15F.
Open
Open I/O ports 160 - 16F.
Closed
Closed I/O ports 170 - 17F.
Closed
W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF.
-7 Open
Open BIOS address C:8000 - C:9FFF.
Open
Open BIOS address C:E000 - C:FFFF.
Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
W2 -1 Reserved.
-2 Reserved.
-3 Reserved.
-4 Closed (Default) BIOS ROM enabled.
Open BIOS ROM disabled.
-5 Closed (Default) ROM and RAM enabled.
Open ROM and RAM disabled.
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-1670
21
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C61, 93, 1, 0
T66, 91, 0, 1, J2
T16, 76, 0, 1, J3
C21, 93, 1, 0
T26, 91, 0, 1, J5
T55, 85, 0, 1, Terminator Terminator
T48, 84, 0, 1, F1
T44, 81, 0, 1, W4
T73, 55, 0, 1, W1
T58, 66, 0, 1, W3 W2
{
Drives: 7 SCSI devices supported.
2 floppy drives (360KB, 720KB, 1.2MB, or 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
J5 Floppy connector.
F1 Thermal fuse.
W1 -1 Open IRQ 3.
-2 Open
-3 Open
-1 Closed (Default) IRQ 5.
-2 Open
-3 Open
-1 Open IRQ 10.
-2 Closed
-3 Open
-1 Closed IRQ 11.
-2 Closed
-3 Open
-1 Open IRQ 12.
-2 Open
-3 Closed
-1 Closed IRQ 14.
-2 Open
-3 Closed
-1 Open IRQ 15.
-2 Closed
-3 Closed
W1 -4 Open I/O ports 140 - 14F.
-5 Open
Closed I/O ports 150 - 15F.
Open
Open I/O ports 160 - 16F.
Closed
Closed (Default) I/O ports 170 - 17F.
Closed
W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF.
-7 Open
Open BIOS address C:8000 - C:9FFF.
Open
Open BIOS address C:E000 - C:FFFF.
Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
W2 -1 Closed (Default) BIOS enabled.
-2 Closed
Open BIOS disabled.
Open
W3 -1 Closed (Default) Floppy controller enabled.
-2 Closed
-3 Closed
Open Floppy controller disabled.
Open
Open
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-1680-solder
01
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C61, 93, 1, 0
T66, 91, 0, 1, J2
T6, 78, 0, 1, J3
C28, 93, 1, 0
T33, 91, 0, 1, J5
C8, 93, 1, 0
T13, 91, 0, 1, J6
T58, 85, 0, 1, Term. W3 Term.
T47, 91, 0, 1, F1 W4
T73, 55, 0, 1, W1
T64, 60, 0, 1, W2
{
Drives: 7 SCSI devices supported.
4 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
J5 Primary floppy connector.
J6 Secondary floppy connector.
F1 Thermal fuse.
W1 -1 Open IRQ 3.
-2 Open
-3 Open
-1 Closed (Default) IRQ 5.
-2 Open
-3 Open
-1 Open IRQ 10.
-2 Closed
-3 Open
-1 Closed IRQ 11.
-2 Closed
-3 Open
-1 Open IRQ 12.
-2 Open
-3 Closed
-1 Closed IRQ 14.
-2 Open
-3 Closed
-1 Open IRQ 15.
-2 Closed
-3 Closed
W1 -4 Open (Default) I/O ports 140 - 14F.
-5 Open
Closed I/O ports 150 - 15F.
Open
Open I/O ports 160 - 16F.
Closed
Closed I/O ports 170 - 17F.
Closed
W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF.
-7 Open
Open BIOS address C:8000 - C:9FFF.
Open
Open BIOS address C:E000 - C:FFFF.
Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
W2 -1 Closed (Default) Primary floppy enabled.
Open Primary floppy disabled.
-2 Closed Secondary floppy enabled.
Open (Default) Secondary floppy disabled.
-3 Closed HD controller disabled.
Open (Default) HD controller enabled.
-4 Reserved.
-5 Reserved.
W3 All Reserved.
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
//TMC-1680-surface
01
D82, 82, 95, 82
D95, 82, 95, 60
D95, 60, 82, 60
D82, 60, 82, 82
T95, 72, 0, 1, J1
C61, 93, 1, 0
T66, 91, 0, 1, J2
T6, 78, 0, 1, J3
T6, 55, 0, 1, J4
C12, 93, 1, 0
T17, 91, 0, 1, J5
C12, 85, 1, 0
T17, 84, 0, 1, J6
T56, 85, 0, 1, Terminator Terminator
T47, 86, 0, 1, W4
T73, 55, 0, 1, W1
T55, 60, 0, 1, W2
{
Drives: 7 SCSI devices supported.
4 floppy drives (360KB, 720KB, 1.2MB, and 1.44MB).
J1 External SCSI connector.
J2 Internal SCSI connector.
J3 LED connector.
J5 Primary floppy connector.
J6 Secondary floppy connector.
W1 -1 Open IRQ 3.
-2 Open
-3 Open
-1 Closed (Default) IRQ 5.
-2 Open
-3 Open
-1 Open IRQ 10.
-2 Closed
-3 Open
-1 Closed IRQ 11.
-2 Closed
-3 Open
-1 Open IRQ 12.
-2 Open
-3 Closed
-1 Closed IRQ 14.
-2 Open
-3 Closed
-1 Open IRQ 15.
-2 Closed
-3 Closed
W1 -4 Open (Default) I/O ports 140 - 14F.
-5 Open
Closed I/O ports 150 - 15F.
Open
Open I/O ports 160 - 16F.
Closed
Closed I/O ports 170 - 17F.
Closed
W1 -6 Closed (Default) BIOS address C:A000 - C:BFFF.
-7 Open
Open BIOS address C:8000 - C:9FFF.
Open
Open BIOS address C:E000 - C:FFFF.
Closed
Closed BIOS address D:E000 - D:FFFF.
Closed
W2 -1 Closed (Default) Primary floppy enabled.
Open Primary floppy disabled.
-2 Closed Secondary floppy enabled.
Open (Default) Secondary floppy disabled.
-3 Closed HD controller disabled.
Open (Default) HD controller enabled.
-4 Closed (Default) BIOS ROM enabled.
Open BIOS ROM disabled.
-5 Closed (Default) ROM and RAM enabled.
Open ROM and RAM disabled.
W4 Open Termination power disabled.
Closed Termination power enabled.
Terminators: Default is installed. If this is not the 1st or last
in a series of SCSI devices, or if in-line terminators
are in use, remove all terminating resistor packs.
}
*
