AdapterId 07FFAh
AdapterName "Iomega PC4B/50 SCSI Host Adapter Board"
NumBytes 4
FixedResources pos[0]=00XXXXXXb pos[1]=X11XXXXXb
NamedItem
Prompt "I/O Address Select"
choice "240" pos[0]=XXXX001Xb io 00240h-0025Fh
choice "340" pos[0]=XXXX010Xb io 00340h-0035Fh
choice "400" pos[0]=XXXX011Xb io 00400h-0041Fh
choice "420" pos[0]=XXXX100Xb io 00420h-0043Fh
choice "3240" pos[0]=XXXX101Xb io 03240h-0325Fh
choice "8240" pos[0]=XXXX110Xb io 08240h-0825Fh
choice "A240" pos[0]=XXXX111Xb io 0A240h-0A25Fh
choice "Disabled" pos[0]=XXXX000Xb
Help
"You may set the PC4 adapter to any one of the I/O Addresses
listed. The first choice is recommended. Make your selection
by using the F5=Previous or the F6=Next keys. If your selection
conflicts with an I/O address already assigned in your system,
it will be marked with an asterisk and you must select an
alternate address."
NamedItem
Prompt "DMA Level Select"
choice "DMA Level 5" pos[1]=1XXX0101b arb 5
choice "DMA Level 6" pos[1]=1XXX0110b arb 6
choice "DMA Level 7" pos[1]=1XXX0111b arb 7
choice "DMA Disabled" pos[1]=0XXX0000b
Help
"The PC4 supports the direct memory access (DMA) mode of data
transfer. Most operating systems require this option to be
enabled. Each DMA level has a corresponding priority level;
the lower the DMA level, the higher the corresponding priority.
You may select any one of the DMA levels listed by using the
F5=Previous or the F6=Next keys. We recommend you select the
first level listed, DMA level 5. If your selection conflicts
with a DMA level already assigned in the system, it will be
marked with an asterisk and you must select an alternative level."
NamedItem
Prompt "Fairness"
choice "Fairness Enabled" pos[1]=XXX1XXXXb
choice "Fairness Disabled" pos[1]=XXX0XXXXb
Help
"If 'Fairness' is enabled, the PC4 adapter will not compete for
the channel during the next arbitration phase if it is currently
in control of the channel. This allows other installed adapters
to obtain the channel in the next sequence based on each adapter's
assigned priority level. When 'Fairness' is disabled, the adapter
will compete for every arbitration phase and will obtain more than
its fair share of channel usage. We recommend you use 'Fairness
Enabled' for all adapters. Select this option using the F5=Previous
and the F6=Next keys."
NamedItem
Prompt "IRQ level"
choice "IRQ 7" pos[0]=XX10XXXXb pos[2]=1XXXXXXXb int 7
choice "IRQ 5" pos[0]=XX01XXXXb pos[2]=1XXXXXXXb int 5
choice "IRQ 3" pos[0]=XX00XXXXb pos[2]=1XXXXXXXb int 3
choice "IRQ 9" pos[0]=XX11XXXXb pos[2]=1XXXXXXXb int 9
choice "IRQ Disabled" pos[2]=0XXXXXXXb
Help
"Operation with multi-tasking operating systems may require the
use of an IRQ signal when the PC4 requires processor service.
No other adapter may be assigned the same IRQ level as the PC4.
For DOS-only systems, this option may be disabled. Choices are:
IRQ 3, 5, 7, 9, or Disabled. Select this option using the
F5=Previous and the F6=Next keys."
NamedItem
Prompt "Memory Address Select"
choice "Disabled" pos[3]=XXXXX000b
choice "D400" pos[3]=XXXXX111b mem 0d4000h-0d5fffh
choice "D200" pos[3]=XXXXX110b mem 0d2000h-0d3fffh
choice "D000" pos[3]=XXXXX101b mem 0d0000h-0d1fffh
choice "CE00" pos[3]=XXXXX100b mem 0ce000h-0cffffh
choice "CC00" pos[3]=XXXXX011b mem 0cc000h-0cdfffh
choice "CA00" pos[3]=XXXXX010b mem 0ca000h-0cbfffh
choice "C800" pos[3]=XXXXX001b mem 0c8000h-0c9fffh
Help
"You may set the PC4 adapter to any one of the Memory Addresses
listed. The first choice is recommended for systems with a fixed
disk installed. Make your selection by using the F5=Previous or
the F6=Next keys. If your selection conflicts with an memory
address already assigned in your system, it will be marked with
an asterisk and you must select an alternate address."
