╔══════════════════════════════════════════════════════════════2616ESA.asc═══╗ ║ M2616/ES/ESA/ESB Jumper Location SCSI Interface ║ ╠════════════════════════════════════════════════════════════════════════════╣ ║ ║ ║ Zylinder: 1542 Köpfe: 2/4 Single-ended SCSI ║ ║ Sektoren: 34 (512bytes/sector) Capacity formatted: ║ ║ 105.MB (Mio. Bytes) ║ ║ ┌─────────────────────────────────────────┐ ║ ║ Power- ░ ┌─┐1 │ ║ ║ connector ░ │C│ │ ║ ║ ░ │N│ │ ║ ║ Pin 1 ▓ │H│ │ ║ ║ ▓ │2│ │ ║ ║ ▓ └─┘9 ┌───┐ │ ║ ║ SCSI- ▓ 4└SW1┘1 │ ║ ║ connector ▓ ┌─┐1 │ ║ ║ ▓ │C│ │ ║ ║ ▓ │N│ │ ║ ║ ▓ │H│ │ ║ ║ ▓ │1│ │ ║ ║ Pin 50▓ └─┘11 │ ║ ║ └─────────────────────────────────────────┘ ║ ║ ║ ║ CNH1 ║ ║ 1-2 2-3 SCSI parity option 4-5 5-6 Synchronous transfer mode ║ ║ S O Enable * S O Enable * ║ ║ O S Disable O S Disable ║ ║ ║ ║ DIP-Switch ║ ║ 1 Write protect 2 Motor control ║ ║ ON Protect ON Self-starting mode * ║ ║ OFF Not protect * OFF Wait motor Start/Stop command ║ ║ ║ ║ 3 Self diagnostic mode 4 Not used, must be off ║ ║ ON Normal mode ║ ║ OFF Test mode * ║ ║ ║ ║ CNH1 SCSI terminator power ║ ║ 7-8 10-11 ║ ║ S S SCSI bus terminator power source is used * ║ ║ IDD terminator power source is used (*1) ║ ║ 8-9 10-11 ║ ║ S S IDD terminator power source is used ║ ║ 7-8 9-10 ║ ║ S S SCSI bus terminator power source is used ║ ║ ║ ║ *1 IDD terminator power = IDD power voltage ║ ║ (5V) -3V = 4.7V) ║ ║ ║ ║ CNH2 (shorted) SCSI ID * = Default setting ║ ║ 2-3 5-6 8-9 0 * (Werkseinstellung) ║ ║ 1-2 5-6 8-9 1 S = Shorted ║ ║ 2-3 4-5 8-9 2 O = Open ║ ║ 1-2 4-5 8-9 3 ║ ║ 2-3 5-6 7-8 4 ║ ║ 1-2 5-6 7-8 5 ║ ║ 2-3 4-5 7-8 6 ║ ║ 1-2 4-5 7-8 7 ║ ║ ║ ╚════════════════════════════════════════════════════════════════════════════╝