*PowerSCSITitle
PowerSCSI! (TM) Installation v1.00 
*PowerSCSICopyRight
(c) Future Domain Corporation, 1993
*PowerSCSIText
How would you like to install PowerSCSI! (TM)?
*PowerSCSIMenu
Auto
Custom
Cancel
*DefaultsTitle
Boot Drive and Target Directory
*DefaultsText
Enter the correct boot drive and the target directory, or press [ENTER] 
to accept the defaults. 
*CustomTitle
Custom Installation
*CustomText
Each file you select from the files menu by pressing [ENTER] will be 
installed to the appropriate system file (either CONFIG.SYS or 
AUTOEXEC.BAT).  Pressing the TAB key will toggle you between the 
information window and Files menu.  When you are finished, press 
ESCAPE to continue.
*CustInfo
File Description
*CustomFile
Files
*InstallFileTitle
Install File
*InstallFileText
This line will be installed to either the CONFIG.SYS or AUTOEXEC.BAT file.  
To accept the default, press the ENTER key.  If you wish to exit without 
making changes, press ESCAPE.  Otherwise, edit the entry and press ENTER.
*YesNoMenu
Yes
No
*OkMenu
OK
*ErrorInstallingFile
There was an error installing this file.
*FileInstalledText
This file is already installed.  Do you wish to replace it?
*UpdateConfigTitle
Updating CONFIG.SYS
*UpdateConfigText
Changes should be made to the CONFIG.SYS file.  Would you like to update 
CONFIG.SYS?
*UpdateAutoexecTitle
Updating AUTOEXEC.BAT
*UpdateAutoexecText
Changes should be made to the AUTOEXEC.BAT file.  Would you like to update 
AUTOEXEC.BAT?
*NoDevicesFoundTitle
No SCSI peripherals Found
*NoDevicesFoundText
No SCSI peripherals were found while scanning the SCSI bus. 
No changes have been made to the system files.
*CAMInstalledTitle
CAM Installed
*CAMInstalledText
CAM has been successfully installed.  You must reboot your system and 
rerun this program to install the necessary PowerSCSI! (TM) device drivers.
*CAMNotInstalledTitle
CAM Not Installed
*CAMNotInstalledText
CAM has not been successfully installed. You must install CAM before 
installing the PowerSCSI! (TM) drivers.
*PowerSCSIInstalledTitle
PowerSCSI! (TM) Installed
*PowerSCSIInstalledText
PowerSCSI! (TM) has been installed successfully.  To enable the drivers 
reboot your system.
*PowerSCSINotInstalledTitle
PowerSCSI! (TM) Not Installed
*PowerSCSINotInstalledText
PowerSCSI! (TM) has not been successfully installed. 
*NoWindowsSupportTitle
Windows Device Driver
*NoWindowsSupportText
Windows device drivers may not be installed using the DOS installation 
program.  To install Windows drivers, you must run the PowerSCSI! (TM) Windows 
Installation program.
*TMC950Found1
A TMC-950 chip based SCSI controller has been found at 
*TMC950Found2
. Please select the correct interrupt for this SCSI controller.
*TMC950IntTitle
TMC 950 SCSI Controller Found
*NoChangesMadeTitle
No Changes Made
*NoChangesMadeText
No updates are required to your system.  No changes have been made to 
your system files.
*InstallingTitle
Installing
*InstallingText
DINSTALL is scanning the SCSI bus and copying the necessary files to 
the target directory.  When PowerSCSI! (TM) has completed this process, 
you will be asked if you would like to update your CONFIG.SYS and 
your AUTOEXEC.BAT files.  If you update these files, the original 
files will be saved as CONFIG.OLD and AUTOEXEC.OLD.
*ErrorCreatingDirectoryTitle
Error Creating Target Directory
*ErrorCreatingDirectoryText
PowerSCSI! (TM) was unable to create the target directory.  Please try again.