REVEAL SC400 LATEST INFORMATION DOS/Windows (Version 2.3) 4-23-95 Product: MSC4004G & Reveal CDR-272 P/N: 13-019-090 Version: 2.3 1. SOFTWARE PACKAGE CONTENTS The SC400 software package contains (3) 3.5" 1.44M diskette. - This is the DOS plus Windows installation diskette The Installation diskette has the following subdirectories and files: a.) Installation files - INSTALL.EXE - Hard disk installation program - DISK1 - Disk Identification file with File List - INSTALL.DAT - on-line help text file - CDROM.CFG - CDROM Config File - README.TXT - This file b.) DOS Drivers & Files - SNDINIT.EXE - also used as hardware Config and Test Program - VOLTSR.EXE - Volume Memory Resident Program - KARAOKE.EXE - Karaoke Program - CDSETUP.SYS - CD-ROM setup device driver - DEMO8.WAV - 8-bit Wave audio file - DEMO16.WAV - 16-bit Wave audio file - SC400.CFG - Device Configuration file - xxxx.SYS - CD-ROM drivers c.) Windows Drivers & Files (sub Directory: WINDRV) - SC400.DRV - Base Audio Device Driver - MPU401P.DRV - MPU-401 Device Driver - VSC400.386 - Virtual Device Driver - MSMIXMGR.DLL - Microsoft Mixer Manager - MIDIMAP.CFG - Configuration file for Midimapper d.) Windows Audio Application Programs (sub Directory: WINAPP) 2. INSTALLATION PROCESS The hard disk installation program, INSTALL.EXE, will copy the necessary files from OPTi Installation disk into your hard disk. Follow the following procedure to install the software: !!! Note: For Windows users, please exit from Windows and run the installation from DOS. (Assuming you are using floppy drive A, and you wish to install to hard disk drive C) 1. Place the disk labeled "REVEAL SC400 Installation" in Drive A. 2. Type a: and press ENTER to change to Drive A. 3. Type install and press ENTER to begin the installation. INSTALL.EXE will do the followings for you: a.) Create the directory \SC400 in your hard disk drive. b.) Prompt you for CD-ROM and sound card options so that after you have finished the installation and have rebooted your machine, you will be ready to use the sound card. c.) Copy the files in your floppy disk to the SC400 directory and Windows directory respectively. d.) Update your CONFIG.SYS, AUTOEXEC.BAT and SYSTEM.INI files In CONFIG.SYS, the following will be added: - DEVICE=C:\SC400\CDSETUP.SYS /T:S /P:340 (assuming SONY CD-ROM) DEVICE=C:\SC400\SLCD.SYS /D:MSCD000 /B:340 In AUTOEXEC.BAT: - PATH=C:\SC400 (appended) SET SC400=C:\SC400 C:\SC400\SNDINIT /B SET BLASTER=A220 I5 D1 T4 In SYSTEM.INI: - [drivers] WAVE=SC400.DRV AUX=SC400.DRV MIDI=SC400.DRV MIXER=SC400.DRV MIDI1=MPU401P.DRV [386Enh] DEVICE=VSC400.386 SC400.DRV is the Base driver comprising WAVE, MIDI, MIXER and AUXILIARY audio services. MPU401P.DRV is the device driver for MPU-401 Wave Table Synthesis interface which requires a MPU-401 compatible device attached to the MIDI Input/Output port or the Wave Table connector on board the sound card. VSC400.386 is the Virtual Device driver for Windows Enhanced Mode. 3. GETTING HELP ABOUT SNDINIT.EXE You can issue the following command to get information about sndinit.exe: - SNDINIT /? 4. VOLUME CONTROL TSR PROGRAM The volume control memory resident program, VOLTSR.EXE, allows you to change volume using hot keys while you are in a DOS application. The hot keys are: Ctrl-Alt-U Raises the volume Ctrl-Alt-D Lowers the volume Ctrl-Alt-M Mute For example, pressing the CTRL, ALT, and U keys will raise the volume. You need to load the TSR before you can use it. To load the TSR, type VOLTSR at the DOS prompt. 5. KARAOKE PROGRAM The Karaoke.exe program allows user to control the input volume of the microphone on the fly with "HOT KEYS." Before using Karaoke, the VOLTSR.EXE program must be successfully loaded and running. To enable Karaoke Mode, type: "KARAOKE ON" at the DOS prompt. To increase MIC input, use: Ctrl-Alt-PageUp To decrease MIC input, use: Ctrl-Alt-PageDown To disable Karaoke Mode, type: "KARAOKE OFF" at the DOS prompt. 6. CD-ROM Interface Setup Device Driver The CD-ROM Setup Device Driver is called CDSETUP.SYS. This driver sets up the interface of your CD-ROM to the SC400 sound card. Each time you change or add a CD-ROM to your sound card. The line "DEVICE=CDSETUP.SYS..." will be added to the first line of your CONFIG.SYS file before the CD-ROM device driver line. CDSETUP.SYS is defined as follows: DEVICE=[drive:]\[directory]\CDSETUP.SYS /T:[M/S/P/I/X] /P:[address] /I:[IRQ] /D:[DMA] [drive] = drive where you have the driver installed [directory] = directory where the driver is located [M/S/P/I/X] = M stands for Mitsumi S stands for SONY P stands for PANASONIC I stands for IDE drive X stands for disabled [address] = Port address for CD-ROM (320, 330, 340, 360) [IRQ] = Interrupt number (5,7,9,10,11) [DMA] = DMA channel (0, 1, 3) For example, the following line sets up the interface for a Mitsumi CD-ROM: DEVICE=C:\SC400\CDSETUP.SYS /T:M /P:340 /I:10 If you did not specify the /I or /D options, CDSETUP will automatically choose the default setting for the CD-ROM type your have specified. - For Mitsumi, the IRQ is 10 and DMA is disabled. - For SONY, they are both disabled. - FOR PANASONIC, they are both disabled. For IDE drive, you need to just specify the /T:I option. Specifying any other option in addition to this will be ignored. The I/O Port and Interrupt for IDE is located at 170H and Int 15. 7) Run DOS games in Windows Our implementation is designed for those DOS games which have icons in Windows and run in full screen DOS and close after finished. When multiple DOS boxes are open, only the first DOS box owns the audio device. DOS Box support could be very complicated, we have to concentrate our implementation only on those features most useful to the general users. We recommend to run game or play audio in DOS box only one at a time. Close the DOS box which owns the device will return the device to Windows. Then you can play audio in Windows or run another DOS game. !! Note !! a) Sometimes, the Setup of the PIF file of a DOS game is crucial. To make a game work effectively under Windows, you probably have to try a few alternative options through PIF editor. b) Not all the DOS games can run in Windows' DOS BOX. Some of them just don't run because of system restrictions.