OPERATION INSTRUCTIONS

The enclosed ADI printer driver SKFUJI36.COM has been developed 
for FUJITSU 24-wire printers of the DL series in DPL24C PLUS 
emulation with a maximum resolution of 360 * 360 dots per inch.

ADI provides the same functionality and performance as the 
standard device drivers used for AutoCAD and AutoSketch. 
As opposed to other common AutoCAD drivers the ADI drivers 
have to be loaded before starting AutoSketch. 
They are residing in the main memory.

1. Printer Installation

Before starting with the printing set the printer to the following 
values:

EMULATE:		DPL24C PLUS	for 8-color printers
COLOR:		AUTOSEL  (only for 8-color printers)
LF-Code:		LF only
CR-Code:		CR only



2. Driver Installation

Copy the driver via the following command onto your harddisk:

	COPY A:SKFUJI36.COM C:	for AutoSketch

3. Usage of the Driver with AutoSketch

You can only use an ADI printer driver if you have an AutoSketch 
version of 1.04 or higher. If the output of the data is not 
leaded directly to the printer but at first to a file, 
AutoSketch will not enable the information of the file name.
Therefore, exists a driver only for AutoSketch which will 
determine the name to "OUTPUT.LST" if there is an output to a file.
Before starting AutoSketch you first have to load the driver 
SKFUJIE.COM or SKFUJI36.COM for FUJITSU 24 pin dot matrix 
printers, which are using the DPL 24C PLUS command set. 
Proceed according to the following syntax:


C:\SKETCH>SKFUJI36 /M		- monochrome printout
C:\SKETCH>SKFUJI36 /C		- color printout
C:\SKETCH>SKFUJI36 /F		- output into a file
					Filename: OUTPUT.LST

You have to enter SKFUJI36, if you want to delete the 
residentially loaded driver from your main memory.

If the driver is to be loaded automatically then 
SKFUJI36.COM has to be entered together with the right 
parameter in the AUTOEXEC.BAT batch file.

The program must be configured, if ADI is used for the 
first time together with AutoSketch. While starting 
AutoSketch you have to specify the parameter "-R":

C:\SKETCH>SKETCH -R

Now, determine the input device and the monitor in accordance 
with your hardware configuration. By selecting the 
plotter/printer select option 3:    
	AUTODESK DEVICE INTERFACE PRINTER

If this option does not appear in the AutoSketch configuration,
you probably have an old AutoSketch version. In this case 
please contact your dealer.


Programming Text                                       Your Choise
__________________________________________________________________

Hexadecimal interrupt number                                   7bh
Specify plot size in millimeter: <N>                        RETURN
Maximum horizontal (X) plot size in inches <11.0>           13.599
Dots per inch in horizontal (X) direction <100.0>              360
Maximum vertical (Y) plot size in inches <8.50>                 12
Dots per inch in vertical (Y) direction <360.0>                180
__________________________________________________________________

When the following text appears:
DOES THE PRINTER SUPPORT COLOR  <N>
enter <Y> if your printer supports color and the driver with the 
parameter /C for color was selected. Otherwise select <N>.


4.1 Color Allocation with AutoSketch

AutoSketch supports 7 colors: red, yellow, green, cyan, blue,
magenta and black. In order to be able to use these colors 
you have to determine them in the menu item pin information 
as follows:

Color			Pinallocation
_________________________________

Red				1
Yellow				2
Green				3
Cyan				5
Blue				4
Magenta				6
Black				7
_________________________________


In case of blue the printer will use orange, because the color 
blue is not supported by the printer. If you do not want to do 
so, you can also select pin No. 5 (cyan). Then blue appears in 
the same color as cyan and now you have only 6 colors at your
disposal.



5. General Hints for Usage

Due to the limited capacity of the main memory the color printers
can only be selected with 8 pins. This cannot be changed because
of programming reasons. 
We hope you understand our situation. The result is a slower 
printout than in the case of a white-and-black printout, but 
the print quality is the same.

If you should have any problems with the configuration or the 
work with AutoCAD respectively AutoSketch under the ADI-driver,
please call the hotline of your country specific subsidiary 
of Autodesk or FUJITSU.  

We hope that these operation instructions will help you and 
hope you enjoy working with AutoSketch and your Fujitsu printer.