OPERATION INSTRUCTIONS

The enclosed ADI printer driver PPFUJI36.COM has been developed 
for FUJITSU 24-wire printers of the DL series in DPL24C PLUS 
emulation with a maximum resolution of 360 * 360 dots per inch.

ADI provides the same functionality and performance as the 
standard device drivers used for AutoCAD and AutoSketch. 
As opposed to other common AutoCAD drivers the ADI drivers 
have to be loaded before starting AutoCAD. 
They are residing in the main memory.

1. Printer Installation

Before starting with the printing set the printer to the following 
values:

EMULATE:		DPL24C PLUS	for 8-color printers
COLOR:		AUTOSEL  (only for 8-color printers)
LF-Code:		LF only
CR-Code:		CR only



2. Driver Installation

Copy the driver via the following command onto your harddisk:

	COPY A:PPFUJI36.COM C:	for AutoCAD

3. Usage of the Driver with AutoCAD

Before starting AutoCAD you first have to load the driver 
PPFUJI36.COM for FUJITSU 24 pin dot matrix printers, 
which are driven by the DPL 24C PLUS command set.
 
Proceed according to the following syntax:

C:\ACAD>PPFUJI36 /M		- monochrome printout
C:\ACAD>PPFUJI36 /C		- color printout
C:\ACAD>PPFUJI36 /F		- output into a file

If you want to delete the driver that is loaded 
residentially from your main memory, enter the 
filename PPFUJI36.

If the driver is to be loaded automatically then 
PPFUJI36.COM has to be entered together with the right 
parameter in the AUTOEXEC.BAT batch file.

If ADI is used for the first time together with AutoCAD the 
program must be configured. Thus, select the option 
"Configure AutoCAD" from the AutoCAD main menu. In case 
AutoCAD is already configured you are automatically set 
into the configuration mode when starting the program. 
Regarding the item "Configure PRINTER PLOTTER" the ADI 
printer plotter must be selected. 
If this option is not available in the program, in any 
case you must check whether your AutoCAD version comprises 
all drivers (files with the extension .DRV) and whether 
they have been installed into your program.
An UPDATE diskette can be obtained from your AutoCAD 
dealer, if necessary.

After selection of the ADI printer plotter the following 
setting ought to be taken into account when using the 
FUJITSU 24-wire printers of the DL series.

Programming Text                                       Your Choice
__________________________________________________________________

Do you want to specify plot size in millimeter? <N>         RETURN
Maximum horizontal (X) plot size in inches <11.0000>:       13.599
Dots per inch in horizontal direction <100.0>:                 360
Maximum vertical (Y) plot size in inches <8.5000>:              12
Dots per inch in vertical (Y) direction <360.0>:               180
.
.
.
Output format, 0 to 2:                                           2
Hexadecimal Interrupt Code (ADI 0XXh)  <7B>:                RETURN
.
.
.
Do you want to calibrate the printer plotter? <N>           RETURN
Format Units (inch or millimeter)  <Z>:                          M
Plot origin in millimeter <0.00,0.00>:                      RETURN
Standard values for plot format
.
.
.
.
Specify format, width and height                   (siehe Punkt A)
in millimeter <MAX>:

Rotate 2-dimensional plots clockwise by 90 ø? <N>           RETURN
Remove hidden lines? <N>                                    RETURN


Specification of the rule by entering:
plotted millimeters=drawing units or adaptation or? <A>          A

__________________________________________________________________


When entering the format you have the following input 
possibilities:

	- A4, if your printer is to proceed A4 paper
	- MAX, if you want to make use of the entire width of the
	  printer

After the installation you have to abandon the configuration menu. 
In doing so, the changed setting is saved.

5. General Hints for Usage

Due to the limited capacity of the main memory the color printers
can only be selected with 8 pins. This cannot be changed because
of programming reasons. 
We hope you understand our situation. The result is a slower 
printout than in the case of a white-and-black printout, but 
the print quality is the same.

If you should have any problems with the configuration or the 
work with AutoCAD under the ADI-driver, please call the hotline 
of your country specific subsidiary of Autodesk or FUJITSU.  

We hope that these operation instructions will help you and 
hope you enjoy working with AutoCAD and your Fujitsu printer.