Readme File for the Windows Driver for
        HP DeskJet 1200C and HP PaintJet XL300.


Note: To print this file from Windows Notepad or Write you
      must copy it to your hard disk, and then open the copy
      on your hard disk.


Quick Installation from Windows
   -- This is the recommended procedure.

1.	Insert the driver disk into the A (or other) drive of
	your computer.
2.	In the Program Manager, select File and then Run...
3.	On the Command Line, type a:\install and click on OK.
4.	Select the desired configuration in the Installation
	dialog box and click on OK.


Quick Installation from DOS (Windows not running)

1.	Insert the driver disk into the A (or other) drive of
	your computer.
2.	Type:    win a:\install.
3.	Select the desired configuration in the Installation
	dialog box and click on OK.


Standard Windows Installation 
   -- Recommended for Asian Windows and network installations.

1.	Insert the driver disk into the A (or other) drive of
	your computer.
2.	Open the Program Manager in MS Windows.
3.	In the Program Manager, select Main.
4.	In Main, select Control Panel.
5.	n Control Panel, select Printers.

Windows 3.1 Installation:
6.	In the Printers dialog box, click on Add >>.
7.	In the List of Printers list box, double click on the
	Unlisted Printer entry (the first entry in the list.)
8.	In the Install Driver dialog box, type A: (or other
	drive) and click OK.
9.	In the Add Unlisted Printer dialog box, select the 
	appropriate printer name and click OK.
10.	Select a calibration method and then follow the on-
	screen instructions to calibrate your monitor.
11.	After the color maps have been built, check the Use
	Print Manager check box and then click on the Connect
	button.
12.	In the Connect dialog box, double click on the desired
	port, check the Fast Printing Direct to Port check
	box, change the Transmission Retry value to 900 and
	then click OK.
13.	After the color maps have been built, highlight the
	desired printer from the Printers Dialog box, and click
	on Active.  Click on the Set Default Printer button to
	make it the Default printer.
14.	Click OK to close the Control Panel.

Windows 3.0 Installation:
6.	In the Printers dialog box, click on Add Printer >>.
7.	In the List of Printers list box, double click on the
	Unlisted Printer entry (the last entry in the list.)
8.	In the Add unlisted printer dialog box, double click
	on the A: (or other) drive in the Directories list box.
9.	Double click on the driver name, "hppcl5c.drv" in the
	Driver Files list box.
10.	Click on Use Print Manager.
11.	In the Printers dialog box, click on Configure.
12.	In the Printers - Configure dialog box, change the
	Transmission Retry timeout to 900, then click on the
	desired port.
13.	Click on the Setup button.
14.	In the Select Printer dialog box, select the desired 
	printer and click OK.
15.	Select a calibration method and then follow the on-
	screen instructions to calibrate your monitor.
16.	Click OK in the printer's Setup Dialog box.
17.	Highlight the desired printer from the Installed
	Printers box and click on Active.  Double click on
	the printer name to make it the Default printer.
18.	Click OK to close the Control Panel.



SCREEN FONTS FOR WINDOWS

If you use Microsoft Windows 3.0 or 3.1, screen fonts are
available that match those in you printer.  You will be able
to see on your computer screen exactly what your printed
fonts will look like.

To get your free copy of screen fonts for Windows,
call 1-303-353-7650.



ALDUS PERSUASION BITMAP PRINTING

Printing bitmaps (.tif, .pcx, ...) from Aldus Persuasion
produces incorrect output.  In order to repair this
problem, the ALDUS.INI file must be modified by adding the
following lines to the end of the file:

[HP PaintJet XL300]
color printer=1

[HP DeskJet 1200C]
color printer=1

[HP PCL5 Color Printer]
color printer=1

For more information on locating and modifying this file, please
contact Aldus Corporation Software Support.



CORELDRAW 3.0 REV. B SLOW PRINTING

To speed the printing of gradient filled objects in 
CorelDraw 3.0 Rev. B, add the following line to the [CDrawConfig]
section of the coreldrw.ini file:

UseClippingForFills=0

For more information on locating and modifying this file, please
contact Corel Corporation Software Support.


AMI PRO VERSION 3.0 PATTERN FILLS

To print objects with pattern fills correctly, add the following
line to the [AmiPro] section of the amipro.ini file located in
the Windows directory:

DefOptions1=2

For more information on modifying this file, please contact
Lotus Development Corporation Software Support.