STANDARD MICROSYSTEMS CORPORATION Microsoft Windows for Workgroups v3.11 Driver For Ethernet LAN Network Cards INSTALLATION GUIDE This software is licensed by SMC for use by its customers only. Copyright (c) 1996 Standard Microsystems Corporation. All rights reserved. This installation guide describes: o An overview o Supported network cards o Supplied files o Driver installation - Installing Windows for Workgroups and the SMC Driver - Installing the SMC Driver Only OVERVIEW This file explains how to install the Windows for Workgroups driver for x86-based platforms. SUPPORTED NETWORK CARDS o EtherEZ Ethernet network cards (SMC8416 board types) o Elite16 Ethernet network cards (SMC8013 board types) o Ultra16 Ethernet network cards (SMC8216 board type) o Elite network cards (SMC8003 board type) o PLUS Ethernet network cards (SMC/WD8003 board type) o EtherCard PLUS Micro Channel network cards (SMC/WD8003xx/A or 8013xx/A board type) SUPPLIED FILES General files o RELEASE.DOC Release notes for this version of the driver o WFW_311.DOC This file Files to install the driver on Windows for Workgroups o SMC8000W.38_ NDIS3 driver o SMC8000.DO_ NDIS2 driver o OEMSETUP.INF Network information file DRIVER INSTALLATION o Installing Windows for Workgroups and the SMC Driver The following procedure describes how to install Windows for Workgroups v3.11 along with the driver files. This procedure is designed to expedite the driver installation. For information on customizing your installation and Windows desktop, refer to your Windows for Workgroups manual. NOTE: You may choose to run EZStart (refer to the README.DOC file on the SuperDisk, or for further detail, refer to the EZSTART.DOC file found within EZStart) and use its 'Automatic' feature to configure the EtherEZ PnP SMC8416 network card before booting Windows for Workgroups. This will assure a card configuration that does not conflict with other devices installed in your PC. You can also check the correct I/O address of the card for use during the Windows for Workgroups install procedure. If you already have Windows for Workgroups installed and only want to install the SMC driver, proceed to 'Installing the SMC Driver Only'. NOTE: Installing the network card prior to installing Windows for Workgroups may cause Windows for Workgroups to incorrectly identify the EtherEZ PnP SMC8416 network card as a 'SMC StarCard Plus' network card. If so: - Click on 'Networks' - Click on 'No Windows Support for Networks' - Click on 'OK' and on 'Continue' - Follow the prompts and select 'Restart Computer' at the 'Exit Windows Setup' dialog box Note: To install an ODI driver, you will need the NETWARE.DRV file. You can download the current version of this file from Novell's NetWire Forum on CompuServe. 1. Insert the Windows for Workgroups Disk 1 Setup diskette in your computer's disk drive. 2. Change to the drive where you inserted the disk in step 1. Then, at the DOS prompt, type: SETUP 3. Press the Enter key to start the setup procedure. Typically, this procedure takes from 10 to 15 minutes. 4. Follow the screen prompts until the Network Setup window appears. a. Select "Advanced" b. Select "Networks" and "Install Microsoft Windows Network". c. Select "No additional network" or "Other", as necessary. Click on "OK". Refer to your Windows for Workgroups manual for information. d. Select "Sharing" and specify whether you want other users to be able to share your files and printer(s). Then select "OK". e. Select "Drivers". f. Select "Add Adapter". The Add Network Adapter dialog box appears. g. Select "Unlisted or Updated Network Adapter" followed by "OK". 5. When the Install Driver window appears, insert the SuperDisk into your computer's disk drive. 6. In the Install Driver window, specify the path to the driver on the SuperDisk (e.g., A:\WFW). 7. Select "OK". The Unlisted or Updated Network Adapter window appears. 8. Select the appropriate SMC network card (e.g. 'SMC EtherEZ [SMC 8416x]) you are installing followed by "OK". You will be prompted to confirm the Base I/O Port setting. Change from the default (280) to whatever the I/O address of the card is set to and click 'OK'. NOTE: You can use EZStart before booting Windows for Workgroups to verify the correct card configuration. See the note at the beginning of this section. 9. When the Network Drivers window appears, you can use "Add Adapter" and/or "Add Protocol" to add more network cards (up to four) and protocols. Refer to your Windows for Workgroups manual for more information. o To change the Base I/O Port and/or driver type, select "Setup" and make the appropriate selections. (The default selection is 'Real Mode and Enhanced Mode'). o Select "Close" followed by "OK". o When prompted with the Microsoft Windows Networks Names box, select "OK". o Follow the screen prompts to complete the driver installation. Note: The "Install Driver" window will appear. You will be prompted to insert the SMC SuperDisk or a disk with the updated or vendor-provided SMC8000.DOS file. The driver's source path is A:\ WIN95NT (not A:\WFW). 11. At the end of the installation, you will be prompted whether you want to accept all the options you selected and restart your computer or return to DOS. Restart your computer so your options can take effect. Some specifics of the installation process may vary according to each user's needs. Refer to the Microsoft Windows for Workgroups user manual for more information. o Installing the SMC Driver Only The following procedure describes how to install the SMC driver and assumes that Windows for Workgroups v3.11 is already installed. NOTE: Installing the network card prior to installing Windows for Workgroups may cause Windows for Workgroups to incorrectly identify the EtherEZ PnP SMC8416 network card as a 'SMC StarCard Plus' network card. If so: - Click on 'Networks' - Click on 'No Windows Support for Networks' - Click on 'OK' and on 'Continue' - Follow the prompts and select 'Restart Computer' at the 'Exit Windows Setup' dialog box 1. Double-click on the Network Setup icon in the Network window. 2. When the Network Setup dialog box appears, refer to "Installing Windows for Workgroups and the SMC Driver", step 4b. This commercial computer software and documentation is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the Commercial Computer Software -- Restricted Rights clause at FAR 52.227-19, or Alternate III of the Rights in Data -- General clause at FAR 52.227-14, as applicable. The manufacturer / subcontractor is Standard Microsystems Corporation, 80 Arkay Drive, Hauppauge, NY 11788. SMC and Standard Microsystems are registered trademarks; and EtherEZ, EtherCard Elite 16 Ultra, EtherCard Elite 16T Ultra, EtherCard Elite 16C Ultra, EliteSeries, PLUS, EZStart, and SuperDisk are trademarks of Standard Microsystems Corporation. Other product and company names are registered trademarks or trademarks of their respective holders.