Novell NetWare Server 4.x ------------------------- For a NetWare 4.x server configuration, We provides a NetWare Server 4.x ODI driver which is included on the ND4300 PCI Ethernet Adapter driver diskette. Note: ----- The directory structure provided on the ND4300 PCI Ethernet Adapter driver diskette has been setup for automatic OEM installation. Also, more information can be found in the Novell NetWare 4.x documentation. Use the (LOAD) and (BIND) commands to load the NetWare 4.x ODI server driver as described below. For more information on these commands, refer to the Novell NetWare 4.x LAN Driver Installation documentation. There are two methods for loading the NetWare Server 4.x driver: (1) use the server command line prompt (":") or (2) edit the (AUTOEXEC.NCF) file. Note: ----- If you use the server command line, you will need to load the driver each time the system is booted. If you edit the AUTOEXEC.NCF file, it will automatically load the driver each time your system is booted. Follow the steps listed below: 1 Install NetWare 4.x on your system. 2 Copy the ODI Server driver (ND4300.LAN) from the ND4300 PCI Ethernet Adapter driver diskette to the hard disk directory where the NetWare 4.x system files are located. The following path should be used to access the files from the ND4300 PCI Ethernet Adapter driver diskette: A:\SERVER.ODI\4.x\ND4300.LAN 3 Boot NetWare by executing (SERVER.EXE). Refer to the appropriate Novell NetWare documentation on loading disk drivers and mounting volumes for more information. 4 To load the driver manually, follow the steps listed below. If you want to load the driver using (AUTOEXEC), go to step 5. Notes: ------ 1) You will need to specify the DOS path if the driver is located in a DOS partition. Type the following command at the file server console: LOAD ND4300 Next, bind the driver to the IPX protocol stack by typing: BIND IPX TO ND4300 NET=xxxx (Bind to IPX or any other protocol stack; where e.g., xxxx=1234) Then press . The installation of the NetWare Server 4.x driver is now complete. 5 To load the driver using (AUTOEXEC), you must first edit the (AUTOEXEC.NCF) file. * Type "LOAD INSTALL" at the server prompt (":") to access the Install Utility. * Open the "MAINTENANCE/SELECTIVE INSTALL" menu and select the "NCF File Options" from the menu to access "EDIT AUTOEXEC". * Then add the following command lines to the (AUTOEXEC.NCF) file. An example with a ND4300 PCI Ethernet Adapter: LOAD ND4300 FRAME=Ethernet_802.2 BIND IPX TO ND4300 NET=xxxx (Bind to IPX or any other protocol stack; where e.g., xxxx=1234) The installation of the NetWare Server 4.x driver is now complete. Notes: ------ 1) You will need to specify the DOS path if the driver is located in a DOS partition. FRAME (Multiple Frame Type Support) ----------------------------------- The FRAME keyword should be used with the LOAD command to designate the desired frame type. In addition, to support multiple FRAME types, the BOARD keyword must be used in conjunction with the FRAME keyword if no IO Address is specified. The available frame types: Ethernet_802.2 Ethernet_802.3 Ethernet_SNAP Ethernet_II Please refer to the appropriate Novell NetWare documentation for details regarding each frame type. For example, to load multiple frame types for one ND4300 PCI Ethernet Adapter, the following commands should be entered: LOAD ND4300 FRAME=Ethernet_802.2 LOAD ND4300 FRAME=Ethernet_802.3 LOAD ND4300 FRAME=Ethernet_II LOAD ND4300 FRAME=Ethernet_SNAP Then press . Finally, the driver must be (binded) to the IPX protocol for each frame type based on the procedure provided in the Novell NetWare documentation. FRAME (Single Frame Type Support) --------------------------------- The FRAME keyword should be used with the LOAD command to designate the desired frame type. For single FRAME support, no BOARD keyword is needed to designate the frame type. The available values and description to load FRAME types is explained above. NAME ---- The NAME keyword may be used with the LOAD command to specify the board number to the selected physical adapter board. This keyword is used to load a different frame type to the same board. For example LOAD ND4300 FRAME=ETHERNET_802.2 NAME=E_802.2 BIND IPX TO E_802.2 LOAD ND4300 FRAME=ETHERNET_802.3 NAME=E_802.3 BIND IPX TO E_802.3 Loading Multiple ND4300 PCI Ethernet Adapters --------------------------------------------- The driver must be loaded again for each new ND4300 PCI Ethernet Adapter installed in the system. If more than one adapter card will be installed, the user must specify the Board's Ethernet ID for each card. For example, to load two ND4300 PCI Ethernet Adapters: LOAD ND4300 Found Board 1: port D000, int 11, EtherID=002018ff0088 Found Board 2: port 8000, int 15, EtherID=002018ff0077 Now you can Specify '1' or '2' to select the ND4300 PCI Ethernet Adapter to load. Then press . NOTE : If you want to use two or more ND4300 PCI Ethernet Adapters on your NetWare server. please run the configuration utility(NDCDIAG.EXE) to view Adapter's Ethernet ID setting first. -------------------------------------[END]--------------------------------------