Windows 95 This document explains how to install network drivers for an EtherExpress 16, 16TP, 16C, FLASH, or MCA adapter on a Microsoft* Windows* 95 workstation. DRIVER LOCATION ================ Drivers are located in the following locations on the EtherExpress 16 LAN Adapter Configuration and Driver disk that came with your adapter: \WIN95\EE16MINI.SYS \WIN95\NETEE16.INF BEFORE YOU START ================ You must configure and test the EtherExpress 16 adapter with SOFTSET.EXE before adding the adapter to Network Setup in Windows 95. Boot the workstation with a DOS disk, and then insert the EtherExpress 16 LAN Adapter Configuration and Driver disk into drive A. At the DOS prompt type: A:SOFTSET 1. Select "AUTOMATIC SETUP" to let SOFTSET configure the EtherExpress 16 adapter to work in your computer, or select "MANUAL SETUP" if you want to designate which interrupt and I/O address you want the EtherExpress 16 to use. 2. Select "RUN DIAGNOSTICS" from the main menu to test the configuration you have selected. If the EtherExpress 16 adapter fails diagnostics, it may not function correctly under Windows 95. NOTE: SoftSet is a DOS program and will not run in Windows 95. You must run SoftSet from DOS. If you already have Windows 95 installed on your computer, You can boot to DOS by inserting a DOS boot disk into your floppy disk drive A when rebooting, or you can select "RESTART THE COMPUTER IN MS-DOS MODE" when you shut down (choose Shut Down from the Start menu in Windows 95). GENERAL INSTALLATION ====================== 1. Open the "My Computer" icon. 2. Open the "Control Panel" icon from the My Computer window. 3. Open the "Network" icon from the Control Panel window. 4. If you're replacing a previously installed LAN adapter, select the old adapter and click "Remove". 5. From the Configuration tab, click "Add". 6. From the Select Network Component Type window, select "Adapter" and click "Add". 7. From the Select Network Adapter window, click "Have Disk". 8. From the Install From Disk window, insert the EtherExpress 16 LAN Configuration and Driver disk into drive A: and specify the path as: A:\WIN95 9. From the Select Network Adapter window, select "Intel EtherExpress 16 or 16TP" from the list of models and click "OK". NOTE: If you are using an EtherExpress 16 MCA (IBM PS/2 MicroChannel), select "EtherExpress 16 (MCA)" from the models list. 10. The Network window then shows a list of the installed components. Windows 95 adds two default protocols: IPX/SPX-compatible protocol and NetBEUI. 11. To share files and printers on this workstation, click "File and Print Sharing" and select the options you want. 12. From the Network Window, click the Identification tab, enter a unique computer name and the name of your new or existing workgroup. 13. Select the Configuration tab. Select "Intel EtherExpress 16 or 16TP" from the list and click Properties. 14. From the EtherExpress 16 or 16TP Adapter Properties window, click the Resources tab. Then specify the configuration type as "Basic Configuration 0", select the interrupt and I/O address range that you set earlier using SoftSet, and click "OK". NOTE: In the EtherExpress 16 Advanced Properties, there is a setting for I/O Channel Ready. The default I/O Channel Ready setting is "LATE", which sets the EtherExpress 16 adapter to run in 16-bit mode. This setting is recommended for most systems. Setting I/O Channel Ready to "NEVER" forces the adapter into 8-bit mode. This setting is required when the EtherExpress 16 can pass the On-board diagnostics in SoftSet only when the Force 8-bit operation is set to "YES". DO NOT set I/O Channel Ready to "EARLY". Setting the I/O Channel Ready to "EARLY" may cause the adapter to become inoperable. 15. When Windows 95 finishes copying files and updating the network configuration, and you are prompted to restart your computer for the changes to take effect, click "Yes". TROUBLESHOOTING TIPS ==================== INTEL ETHEREXPRESS 16 OR 16TP (0000) IS NOT WORKING PROPERLY ------------------------------------------------------------ If Windows 95 fails to detect or initialize the EtherExpress 16, you will get this error message when starting Windows 95: "Your network adapter Intel EtherExpress 16 or 16TP (0000) is not working properly. You may need to set it up again. For more information, see the Network Troubleshooting in Windows help." Try these steps: 1. Verify that the I/O address and interrupt that you specified for the EtherExpress 16 is correct by running SOFTSET.EXE and selecting "View Configuration" from the menu. If the I/O address or interrupt is different from the value you specified when installing Windows 95, select "Manual Setup" from the SoftSet main menu and change the I/O address and interrupt to match the settings in Windows 95. 2. Verify that the I/O address and interrupt being used by the EtherExpress 16 adapter are not being used by any other device in your workstation, including a sound card, faxmodem, scanner, tape backup, serial port, or parallel port. Look at the documentation or setup programs for the other installed adapters in your computer to verify what I/O address and interrupts they are using. Some sound cards use multiple interrupts and I/O addresses. For example, a typical sound card will use an I/O address of 220 and IRQ 5 for the sound port and an I/O address of 330 and IRQ 11 for the MIDI/Joystick port. 3. Verify that the EtherExpress 16 passes all diagnostic tests by running SOFTSET.EXE from DOS and selecting "Run Diagnostics". If the EtherExpress 16 fails diagnostics it will not function correctly under Windows 95. If On-Board diagnostics fail, try setting the adapter to use a different I/O address, specify a different interrupt, or set the Force 8-bit option to "Yes". If On-Network diagnostics fail, there is likely a cable, connector, or hub problem. Verify that the cabling you are using is connected properly and that the cable is not defective. For more information on cable specifications, view the 10BaseT or COAX ethernet cabling readme files on the EtherExpress 16 LAN adapter Configuration and Drivers disk. Note: "Responder not found" is NOT an error. This message will be displayed IF YOU ARE NOT RUNNING THE SOFTSET RESPONDER ON ANOTHER MACHINE with an EtherExpress card or if the card cannot actually communicate with the responder card. If you do not have a responder running or if the two cards cannot communicate, the diagnosticss will try to send packets back to itself. ADAPTER PASSES DIAGNOSTICS BUT STILL DOES NOT WORK WITH WINDOWS 95 ------------------------------------------------------------------ If the adapter passes diagnostics but still does not work with Windows 95, there could be a problem with the network setup configuration. If you've made several attempts to configure the network setup for Windows 95 or had another adapter installed before the EtherExpress 16 adapter, it may be necessary to restore the Windows 95 network configuration to default settings and then reconfigure the Windows 95 network setup. Here's how: 1. Open the "My Computer" icon. 2. Open the "Control Panel" icon from the My Computer window. 3. Open the "Network" icon from the Control Panel window. 4. Select the "Intel EtherExpress 16 or 16TP" from the Network Components list, and click "Remove". This removes the adapter and all associated components from the Windows 95 network configuration. 5. From the Network Configuration window, click "OK". 6. When Windows 95 finishes copying files and updating the network configuration, you will be prompted to restart your computer for the changes to take effect, click "Yes". 7. After the workstation reboots, continue at step 1 of the GENERAL INSTALLATION section of this document. * Third-party trademarks are the property of their respective owners.