LAN Manager server

  LAN Manager* 2.1 server or workstation installation

  This document applies to the EtherExpress(tm) 16, 16TP, 16C, FLASH,
  FLASH TP, FLASHC, MCA, and MCA/TP adapters.  It contains notes for 
  installing the NDIS driver in a LAN Manager server, OS/2* workstation 
  and DOS workstation.  It does not explain how to configure an 
  EtherExpress adapter. For instructions about configuring the adapter, 
  see the printed installation guide.


  FOR A NEW SERVER OR OS/2 WORKSTATION
  ------------------------------------
  1.   To use the EtherExpress 16 adapter in an initial LAN Manager Server
       installation, follow the standard installation procedure (using the
       SETUP utility).  An EtherExpress driver is included with LAN Manager
       2.1, but you MUST update that driver with the one on the 
       EtherExpress adapter disk.
  
  2.   Once you exit the SETUP utility, do NOT shut down the computer. 
       Verify that the I/O address in PROTOCOL.INI matches the I/O
       address of the board.  Refer to the "EDITING PROTOCOL.INI" section
       below for instructions on changing the I/O address.
  
  3.   After exiting SETUP, reboot the computer as described in the manual. 
       If an error message is displayed, ensure that the board is installed
       properly and the I/O address in PROTOCOL.INI matches the board.  You
       may also run the Intel status-checking utility (described at the end
       of this file).
  
  FOR AN EXISTING SERVER OR OS/2 WORKSTATION
  ------------------------------------------
  These instructions assume that the LAN MANAGER operating system has
  already been installed on the server or workstation.  
  
  1.   To install the EtherExpress adapter in an existing Server, use the
       LAN Manager SETUP utility and choose EtherExpress as the network
       adapter.  An EtherExpress driver is included with LAN Manager 2.1,
       but you MUST update that driver with the on the EtherExpress disk.
  
  2.   Once you exit the SETUP utility, do NOT shut down the computer.
       Verify that the I/O address in the Protocol.ini matches the I/O
       address of the board.  Refer to the "EDITING PROTOCOL.INI" section
       below for instructions on changing the I/O address.
  
  3.   Reboot the computer as described in the manual.  If an error message
       is displayed, ensure that the board is installed properly and the I/O
       address in PROTOCOL.INI matches the board.  You may also run the
       Intel status-checking utility (described at the end of this file).
  
  DOS WORKSTATIONS
  ----------------
  1.   To use the EtherExpress card in a DOS workstation, follow the
       standard installation procedure (using the SETUP utility).  An 
       EtherExpress driver is included with LAN Manager 2.1, but you must 
       update that driver with the one on the EtherExpress disk.
  
  2.   Once you exit the SETUP utility, do NOT shut down the computer. 
       Verify that the I/O address in the PROTOCOL.INI matches the I/O 
       address of the board.  Refer to the "EDITING PROTOCOL.INI" section
       below for instructions on changing the I/O address.
  
  3.   After exiting SETUP, reboot the computer as described in the manual. 
       If an error message is displayed, ensure that the board is installed
       properly and the I/O address in PROTOCOL.INI matches the board.  You
       may also run the Intel status-checking utility (described at the end
       of this file).
  
  CONFIGURING THE DRIVER FOR MULTIPLE BOARDS
  ------------------------------------------
  If you're putting multiple boards in one computer, be sure that each board
  has a unique I/O address.  Use the NOS's SETUP utility to update the LAN
  Manager configuration to include the additional boards.  After exiting
  SETUP, you must edit the PROTOCOL.INI file to change the I/O address
  parameters to match the boards.  Refer to the "EDITING PROTOCOL.INI"
  section below for instructions on changing the I/O address.
  
  EDITING PROTOCOL.INI
  --------------------
  LAN Manager uses the PROTOCOL.INI file to ensure that the driver and the
  board are configured to work together.  Our driver requires only one
  parameter, and its purpose is to ensure that the driver and the board are
  configured to use the same I/O address.  The parameter's name is
  IOADDRESS.  If a board is using an I/O address other than 300h, you must
  edit the PROTOCOL.INI file located in the directory \LANMAN to change
  the configuration of the driver.
  
  1.   Using a text editor, locate the EtherExpress section shown below:
   
      [EXP16_NIF]
          
      ; Intel EtherExpress(TM) 16 Ethernet Adapter.
          
      IOADDRESS=0x300
      DRIVERNAME=EXP16$
  
  2.   Replace the I/O address with the address you selected when you ran
       SOFTSET for the EtherExpress 16 or the System Configuration utility
       for the EtherExpress MCA.
  
  3.   Save the file and exit.
  
  The network driver now matches the configuration of the board and you
  should continue with the rebooting of the computer.


* Third-party trademarks are the property of their respective owners.