Model: ULTRA 14N ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ÚÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ ³³ LED ³ ³ ³ ³ ³ ³ ³ÀÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ³ JP2 J1 FLOPPY J2 SCSI ³ ³ÚÄÄÄÄÄÄÄ¿ ³RP ³ ³³ ³JP11 ³4 ³ E ³ÀÄÄÄÄÄÄÄÙ ÚÁ¿ X ³ PORT BIOS ³RP ³ ³ T ³ÚÄ¿ ÚÄÄÄÄ¿ ÚÄÄÄÄÄÄÄ¿ ³6 ³ ³ E ³³.³ JP7 ³. . ³ ³ . . . ³ ³ ³ R ³³.³ ³. . ³ ³ . . . ³ ³RP ³ ³ N ³ÀÄÙ ÀÄÄÄÄÙ ÀÄÄÄÄÄÄÄÙ JP21 ³5 ³ ³ A ³ JP5 JP20 JP10 ÚÄÄÄÄÄÄ¿ ³ ³ L ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄ¿ 2³. . . ³ ³ ³ ³ ³ . . . . . .³ 1³. . . ³ ÀÂÙ S ³ ³ . . . . . .³ JP1 ÀÄÄÄÄÄÄÙ ³ C ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ ÚÄÄÄÄÄ¿ ÚÄÄÄ¿ ³ S ³ ³. . .³ JP3 ³. .³ ³ I ³ ÀÄÄÄÄÄÙ ÀÄÄÄÙ ³ ÀÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÙ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Board Layout ------------ ULTRA 14N DEFAULT JUMPER DEFINITION ----------------------------------- * = Default Setting JP1 EPROM Type Selection (Factory Use) 1-2 : 256K Type *2-3 : 128K Type JP2 LED (Default OPEN) Pin 1 : VCC Pin 2 : Signal Pin 3 : Signal Pin 4 : VCC JP3 Chassis Ground OUT : Not Ground *INT : Grounded JP5 1-2 3-4 : Head mapping selection OUT OUT : 16 head, 63 sector mapping *IN OUT : 64 head, 32 sector mapping OUT IN : 64 head, 63 sector mapping IN IN : 64 head, 32 sector mapping 5-6 7-8 : Interrupt Channel IN IN : IRQ15 *OUT IN : IRQ14 IN OUT : IRQ11 OUT OUT : IRQ10 9-10 : BIOS support for more than 2 SCSI hard drives *OUT : Maximum 2 SCSI hard drives per system IN : Maximum 16 SCSI hard drives per system 11-12 : Synchronous Negotiation *OUT : ULTRA 14N Initiated Negotiation IN : Target Initiated Negotiation JP7 Floppy Controller 1-2 : Floppy Enable/Disable OUT : Disable *IN : Enable JP10 BIOS Address 1-2 3-4 5-6 : BIOS Address OUT OUT OUT : Disable IN OUT OUT : Reserved *OUT IN OUT : C8000 IN IN OUT : CC000 OUT OUT IN : D0000 IN OUT IN : D4000 OUT IN IN : D8000 IN IN IN : DC000 JP11 Floppy Controller 1-2 : 3rd Floppy Cable Seletion *OUT : Double Twisted Cable IN : Single Twisted Cable 3-4 : Floppy Port Control *OUT : Primary Port (3F0-3F7) IN : Secondary Port (370-377) 5-6 : Floppy Drive Type *OUT : Drive configured for AT or equivalent floppy Drive IN : Drive configured for PS/2 or equivalent floppy Drive 7-8 : Precompensation Settings *OUT : Precompensation is fixed at 125ns for all data rates IN : Precompensation varies according to floppy data rate. 250,300 and 500 Khz rate have 250ns, 208ns and 125ns precompensation each. JP21 1-2 : Removable Drive Support *OUT : BIOS Supported IN : External Drive Supported 3-4 : Sync. Negotiation Start Rate *OUT : Begin from 10MB/S IN : Begin from 5MB/S 5-6 : Reserved (Out) JP20 1-2 3-4 : IO Port Address OUT OUT : 140h OUT IN : 220h *IN OUT : 240h IN IN : 340h