ATI Windows 3.1 Display Driver Disk (Accelerator):
=================================================

April 22, 1992 release for:

   ATI 8514 ULTRA
   ATI Graphics ULTRA
   ATI Graphics VANTAGE

Copyright (c) 1992, ATI Technologies Inc.
All Rights Reserved

ATI  Technologies Inc.	reserves all rights with respect to the programs
and drivers supplied.


DISCLAIMER OF WARRANTY:
======================

This software is provided without charge.  This software is provided "as
is".   ATI  makes  no  warranties  of  merchantability  or fitness for a
particular purpose,  either expressed or implied.  ATI (where allowed by
state,	 federal,   or	provincial  law)  assumes  no liability,  either
incidental or consequential arising from use of this product.

------------------------------------------------------------------------

REQUIREMENTS:
============

These  drivers  will  work  with  either  512K  or 1Mbyte of accelerator
memory.  With 512K,  16 colors will be displayed.  On 1Mbyte boards, 256
colors are displayed.

For 800x600 operation, the  Graphics  ULTRA/VANTAGE  ROM version must be
1130111513 (v1.3) or newer.  For  8514  ULTRA  ROMs, the version must be
1330111330 (v1.3) or newer. Please contact ATI Customer  Support for ROM
upgrade details. The ROM  version  label  is  displayed  in  the startup
banner on system startup.

These  drivers  will  work  with  either  512K  or 1Mbyte of accelerator
memory.  With 512K,  16 colors will be displayed.  On 1Mbyte boards, 256
colors are displayed.

------------------------------------------------------------------------

INSTALLATION:
============

Before proceeding through  the  installation steps, configure Windows 3.1
to use the Microsoft 8514/a driver.

1)  Exit Windows (not a DOS box).

2)  Change to your Windows directory (CD).

3)  Place the ATI Windows 3.1 Display Driver Disk into drive A:. Drive B:
    may be used but is not recommended. The Windows 3.1 Setup program may
    behave inconsistently when using drive B:.

4)  Type "SETUP" at the DOS prompt.

5)  Select Display - "Other (Requires disk provided by a hardware manufact.."

6)  Select the desired screen resolution and press Enter. Setup will copy
    files from the diskette into your Windows directories.

    Setup may ask if you  wish  to  KEEP or REPLACE the specified driver.
    Choose REPLACE by pressing ESC. This  choice  will appear if you have
    installed an older ATI driver  with  the  same  file name previously.
    If you are  presented  with  this  choice  AFTER this installation is
    completed  (by  choosing  a  different  ATI  driver selection later),
    choose KEEP by pressing ENTER.

    Setup may ask for some  Windows  diskettes.  In  this case, enter the
    drive that contains the ATI driver disk  (i.e. A:) so Setup continues
    to use this disk.

    An error message may appear  indicating  that there is a problem with
    drive A: during the file  copying  process  (such as VGALOGO.LGO). If
    this occurs, press ESC  twice  (after  each error box appearance) and
    enter the drive  that  contains  the  ATI  driver  disk when asked by
    Setup.

7)  When  Setup  is  complete,  type  "WIN" at the MS-DOS prompt to start
    Windows 3.1.

------------------------------------------------------------------------

Notes - Accelerator based drivers:
=================================

The  following  features  are  missing  from the current ATI Accelerator
drivers disk. These drivers will be provided in a later release.

. Crystal Font drivers

------------------------------------------------------------------------

ATI Customer Support:
====================

ATI Customer Support is available Monday through Friday, 9:00am to 5:30pm
EST.

   Phone: (416) 756-0711
   FAX:   (416) 756-0720
   BBS:   (416) 756-4591  (upto 9600 baud, 8 bits, no parity, 1 stop bit)