STANDARD MICROSYSTEMS CORPORATION Microsoft Windows NT v3.51 NDIS v3.1 Driver For Ethernet LAN Network Cards INSTALLATION GUIDE This software is licensed by SMC for use by its customers only. Copyright (c) 1996 Standard Microsystems Corporation. All rights reserved. This installation guide describes: o Supported network cards o An overview o Supplied files o Driver installation - Primary installation (network card not presently installed) - Network card already installed or older driver previously loaded SUPPORTED NETWORK CARDS o EtherEZ Ethernet network cards (SMC8416 board types) o Elite16 Ethernet network cards (SMC8013 board types) o Ultra16 Ethernet network cards (SMC8216 board type) o Elite network cards (SMC8003 board type) o PLUS Ethernet network cards (SMC/WD8003 board type) o EtherCard PLUS Micro Channel network cards (SMC/WD8003xx/A or 8013xx/A board type) OVERVIEW This file explains how to install the Windows NT driver for x86-based platforms. SUPPLIED FILES General files o NT_351.DOC This file o RELEASE.DOC Release notes for this version of the driver Files to install the driver on Windows NT o SMC8000N.SY_ The driver o SMC8000N.HL_ The driver's associated help file o OEMSETUP.INF The driver's setup file DRIVER INSTALLATION o Primary installation (network card not presently installed) If you've already installed another card or loaded another driver, refer to the procedure titled 'Network card already installed or older driver previously loaded'. NOTE: If you experience any problems during driver installation, you may choose to run EZStart and use its 'Automatic' feature to configure the EtherEZ PnP SMC8416 network card. Refer to the README.DOC file on the SuperDisk, or for further detail, refer to the EZSTART.DOC file found within EZStart. EZStart will not run in a Windows NT DOS window. You must boot from DOS to setup and test the card. 1. Complete the Windows NT installation without the SMC network card installed in your PC. Have the SMC SuperDisk and Windows NT installation files (on CD or hard drive) available. When prompted with a window asking about 'Participating on a network', change the default to 'Do not connect this computer to a network at this time'. Click 'Next' and follow the prompts to reboot. 2. Install the SMC network card. Start Windows NT and double-click the 'Control Panel' and 'Network' icons. 3. You will be prompted to install networking functionality. Click 'Yes'. 4. Follow the screen prompts. When prompted, insert the Windows NT CD or specify the path to those installation files on your hard drive. 5. When prompted with the 'Network Adapter Card Detection' dialog box, select 'Do Not Detect'. Click on 'Continue'. 6. When prompted with the 'Add Network Adapter' window, scroll to and select ' Requires disk from manufacturer'. 7. Select 'Continue'. 8. When prompted, insert the SuperDisk, specify the path to the root directory (e.g., A:\), and click 'OK'. 9. Select 'SMC 8416 EtherEZ' (or appropriate) and click 'OK'. 10. You will be prompted with the 'Adapter Card Setup' window. Verify the correct network card has been detected. Click on 'OK' to accept the default settings. In most cases Windows NT will detect the correct card settings and you will not have to change anything. NOTE: If you select the IPX/SPX protocol, the 'NWLINK IPX/SPX Protocol Configuration' window appears, permitting customization of the protocol. Click 'OK'. 11. At this point, you can install additional protocols and network components via the 'Windows NT Setup' window. Click 'Coninue' when finished. 12. When presented with the 'Network Settings' window, click on 'OK'. 13. Follow the screen prompts as directed. Enter the 'Domain' or 'Workgroup' names when prompted (optional) and click 'OK'. 14. When prompted. select 'Restart Computer'. NOTE: In the unlikely event you encounter any device driver errors after Windows NT boots, check the Event Log (under 'Administrative Tools' icon) to see whether the error is related to your SMC network card. o Network card already installed or older driver previously loaded Follow this procedure to replace Windows NT driver files with the latest SMC driver files. By removing driver files, you will lose network settings. Make sure you have a record of settings such as IP address, workgroup name, etc. Check with your network administrator for complete information. NOTE: If you experience any problems during driver installation, you may choose to run EZStart and use its 'Automatic' feature to configure the EtherEZ PnP SMC8416 network card. Refer to the README.DOC file on the SuperDisk, or for further detail, refer to the EZSTART.DOC file found within EZStart. EZStart will not run in a Windows NT DOS window. You must boot from DOS to setup and test card. 1. Install the SMC network card, attach network cable, and boot Windows NT. 2. Double-click the 'Control Panel' and 'Network' icons. 3. When prompted with the 'Network Settings' window, highlight the network card you wish to remove, click on 'Remove', and click on 'OK'. 4. Select 'Restart Now' when prompted. 5. Start Windows NT and double-click the 'Control Panel' and 'Network' icons. The 'Network Settings' window appears. Select 'Add Adapter'. 6. When prompted with the 'Add Network Adapter' window, scroll to and select ' Requires disk from manufacturer'. 7. Select 'Continue'. 8. When prompted, insert the SuperDisk, specify the path to the root directory (e.g., A:\), and click 'OK'. 9. Select 'SMC 8416 EtherEZ' (or appropriate) and click 'OK'. 10. You will be prompted with the 'Adapter Card Setup' window. Verify the correct network card has been detected. Click on 'OK' to accept the default settings. In most cases Windows NT will detect the correct card settings and you will not have to change anything. 11. At this point, you can install additional protocols and network components via the 'Windows NT Setup' window. Click 'OK' when finished. NOTE: If you select the IPX/SPX protocol, the 'NWLINK IPX/SPX Protocol Configuration' window appears, permitting customization of the protocol. Click 'OK'. 12. When prompted, select 'Restart Now'. NOTE: In the unlikely event you encounter any device driver errors after Windows NT boots, check the Event Log (under 'Administrative Tools' icon) to see whether the error is related to your SMC network card. This commercial computer software and documentation is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the Commercial Computer Software -- Restricted Rights clause at FAR 52.227-19, or Alternate III of the Rights in Data -- General clause at FAR 52.227-14, as applicable. The manufacturer / subcontractor is Standard Microsystems Corporation, 80 Arkay Drive, Hauppauge, NY 11788. SMC and Standard Microsystems are registered trademarks; and EtherEZ, EtherCard Elite 16 Ultra, EtherCard Elite 16T Ultra, EtherCard Elite 16C Ultra, EliteSeries, PLUS, EZStart, and SuperDisk are trademarks of Standard Microsystems Corporation. Other product and company names are registered trademarks or trademarks of their respective holders.