National Datacomm Corporation 

           Novell NetWare Remote Program Load (RPL) Software
              For NDC NE2000 Ethernet Adapter With NDET06

                         INSTALLATION GUIDE


This installation guide describes how to install the Novell NetWare Remote
Program Load (RPL) software on the NetWare 3.1X/4.0X server with NDC NE2000
Ethernet Adapter (ND41XX/ND50XX).

Instructions to be used if establishing RPL with the server using NDET06
Find/Found protocol,associated with the 802.2 protocol frame, boot ROM.

INSTALLATION INSTRUCTIONS FOR NetWare 3.1x/4.0x SERVER

1.   Start the NetWare server. Load and bind the NE2000 with the
     ETHERNET_802.2 frame.

     :LOAD NE2000 FRAME=ETHERNET_802.2
     :BIND IPX TO NE2000

2.   Skip this step if your server is NetWare 3.12/4.0X.
     (RPL.NLM and RBOOT.RPL are already in NetWare 3.12/4.0x. You don't have
     to and should not copy these two files in NDC"Setup Program" diskette to
     NetWare 3.12/4.0x server.)

     Login as supervisor to the NetWare 3.11 server and copy the "RBOOT.RPL"
     file to the F:\LOGIN directory and the "RPL.NLM" file to the  F:\SYSTEM
     directory.

     Note: Both files can be found in the RPL directory of the NDC Ethernet
     "Setup Program" diskette.

3.   Load the RPL support on server.

     :LOAD RPL
     :BIND RPL TO NE2000

4.   The following is an example to build an RPL image.

     (a)  Format a DOS bootable diskette.(FORMAT A:/S)

     (b)  Copy ODI drivers (LSL, NE2000, IPXODI, NETX, NET.CFG..) and
          AUTOEXEC.BAT to the diskette.
         
     Example of AUTOEXEC.BAT and NET.CFG

        AUTOEXEC.BAT:
          PROMPT $P$G
          LSL
          NE2000
          IPXODI
          NETX
               
         NET.CFG
          Link Driver NE2000
             Frame ETHERNET_802.2
             INT 3
             PORT 300

          Note:     INT and PROT need to be adjusted according to the card
                    settings. 
       
     (c)  Put the diskette you just created into drive A: of the PC with
          ND41XX/ND50XX and boot up from A:. Login as "SUPERVISOR" 

     (d)  Change directories to "\LOGIN". 
               Type: CD\LOGIN

     (e)  Map drive F to SYS:SYSTEM
               Type: MAP F:=SYS:SYSTEM <ENTER>

     (f)  Map drive G to SYS:SYSTEM
               Type: MAP G:=SYS:SYSTEM <ENTER>

     (g) Change to the SYS:LOGIN directory
               Type: G: <ENTER>

     (h)  Run DOSGEN to create RPL image file "NET$DOS.SYS". Please delete
          the "NOT-LOGGED-IN" users in server "MONITOR" if "NET$DOS.SYS"
          cannot be built.
               Type: F:DOSGEN <ENTER>

     (i)  Copy the AUTOEXEC.BAT from your bootable diskette to \LOGIN
          directory.
               Type: COPY A:\AUTOEXEC.BAT G:\LOGIN

     (j)  Flag the NET$DOS.SYS file in \LOGIN as sharable.
               Type: FLAG NET$DOS.SYS S      < Novell v.3.1x
               Type: FLAG NET$DOS.SYS S /FO  < Novell v.4.0x

     
5.   Enable RPL for PC with ND41XX/ND50XX & NDET06.

     (a)  Run NDC Ethernet Setup Program. For the ND41XX adapters, run
          "SOFTSET", and for the ND50XX run "NDCONF". Select a range of free
          memory for the RPL PROM to enable the RPL function.

     (b)  Power off the PC and then power on to boot up the PC from NetWare
          server.

                    National Datacomm Corporation 

           Novell NetWare Remote Program Load (RPL) Software
              For NDC NE2000 Ethernet Adapter With NDET07

                         INSTALLATION GUIDE


This installation guide describes how to install the Novell NetWare Remote
Program Load (RPL) software on the NetWare 3.1x/4.0X server with NDC NE2000
Ethernet Adapter (ND41XX/ND50XX).

Instructions to be used if establishing RPL with the server using NDET07 IPX
protocol,associated with the 802.3 protocol frame, boot ROM.

INSTALLATION INSTRUCTIONS FOR NetWare 3.1x/4.0x SERVER

1.   Start the NetWare server. Load and bind the NE2000 with the
     ETHERNET_802.3 frame.

     :LOAD NE2000 FRAME=ETHERNET_802.3
     :BIND IPX TO NE2000


2.   The following is an example to build an RPL image.

     (a)  Format a DOS bootable diskette.(FORMAT A:/S)

     (b)  Copy ODI drivers (LSL, RPLODI, NE2000, IPXODI, NETX, NET.CFG..) and
          AUTOEXEC.BAT to the diskette.
         
     Example of AUTOEXEC.BAT and NET.CFG

     AUTOEXEC.BAT:
          PROMPT $P$G
          LSL
          RPLODI    <Do not use version dated below 3-21-91,if you do your
                    workstation will hang.>
          NE2000
          IPXODI
          NETX
               
     NET.CFG
          Link Driver NE2000
             Frame ETHERNET_802.3
             INT 3
             PORT 300
     Note:     INT and PROT need to be adjusted according to the card
               settings. 
       
     (c)  Put the diskette you just created into drive A: of the PC with
          ND41XX/ND50XX and boot up from A:. Login as "SUPERVISOR".


     (d)  Change directories to "\LOGIN". 
               Type: CD\LOGIN

     (e)  Map drive F to SYS:SYSTEM
               Type: MAP F:=SYS:SYSTEM <ENTER>

     (f)  Map drive G to SYS:SYSTEM
               Type: MAP G:=SYS:SYSTEM <ENTER>

     (g) Change to the SYS:LOGIN directory
               Type: G: <ENTER>

     (h)  Run DOSGEN to create RPL image file "NET$DOS.SYS". Please delete
          the "NOT-LOGGED-IN" users in server "MONITOR" if "NET$DOS.SYS"
          cannot be built.
               Type: F:DOSGEN <ENTER>

     (i)  Use "RPLFIX" to fix the image file "NET$DOS.SYS" if your DOS
          Version used to build the image file is 5.0 or higher.
               Type: RPLFIX NET$DOS.SYS

     (j)  Copy the AUTOEXEC.BAT from your bootable diskette to \LOGIN
          directory.
               Type: COPY A:\AUTOEXEC.BAT G:\LOGIN

     (k)  Flag the NET$DOS.SYS file in \LOGIN as sharable.
               Type: FLAG NET$DOS.SYS S      < Novell v.3.1x
               Type: FLAG NET$DOS.SYS S /FO  < Novell v.4.0x

     
3.   Enable RPL for PC with ND41XX/ND50XX & NDET07.

     (a)  Run NDC Ethernet Setup Program. For the ND41XX adapters, run
          "SOFTSET", and for the ND50XX run "NDCONF". Select a range of free
          memory for the RPL PROM to enable the RPL function.

     (b)  Power off the PC and then power on to boot up the PC from NetWare
          server.


Please refer to p.349-p.352 of "Novell NetWare Version 3.11
Installation" for more detailed information. You may also refer to
p.353-p.360 for creating multiple remote boot image files.