DEC  1994

                       3Com 3+ Share Driver Installation
                                      for
                     D-Link DE-650 PCMCIA Ethernet Adapter
                     =====================================

*********************************** NOTE ***********************************
Each DE-650 series adapter comes with a driver diskette of its own.  If you
have more then one model of DE-650 adapter, make sure that you use the driver
diskette that was included with the DE-650 adapter you are using.
****************************************************************************

The D-Link 3COM 3+ Share Driver Program lets you run 3Com 3+ Share on your PC
with the D-Link DE-650 PCMCIA Ethernet Adapter.

The following files will be used in this installation:

Files		 Contents
------------ 	 ------------------------------------------------------------
DE65NPD.SYS      DE-650 Driver Program.
ETH.SYS 	 3Com 3+ Share Driver.


1. Follow the installation procedure for 3Com EtherLink board.

2. Copy the program ETH.SYS from the Installation Diskette for the D-Link
   DE-650 PCMCIA Ethernet Adapter to the boot disk/diskette.

   This program will replace the program of the same file name (ETH.SYS) from
   the installation procedure in step 1 above.

3. In the CONFIG.SYS file on the boot disk/diskette, make sure you have the
   following statements.  The order of these statements must be as shown below.

      *** PC installed Socket and Card services ***
     DEVICE = DE65NPD.SYS [-d] [-w] <sw_int> <irq> <io_addr> 
     DEVICE = ETH.SYS

	     OR

      *** PC installed Socket service or Databook Cardtalk***
      *** PC's PCMCIA controller is Intel 82365SL ***
      *** PC is Toshiba T3300SL ***
     DEVICE = DCD16.EXE
     DEVICE = DE65NPD.SYS [-d] [-w] <sw_int> <irq> <io_addr> 
     DEVICE = ETH.SYS

  Please refer to \IBMPC\INSTALL\README.DOC for more detail information.

You may now boot and start your 3COM workstation.

Notes:
1. Parameters for DE65NPD.SYS
[-d]		Delay Initial - The driver program will not initialize the
                network interface card until the packet driver program is
                accessed by its upper layer program first time.
[-w]		The -w parameter is for use with the Windows environment only.
<sw_int>	Is the software interrupt vector number used by the packet
		driver program, which can be from 96 to 128.
<irq>		Is the hardware interrupt (IRQ) line set on your network
		interface card. The default is 5 if this parameter is not
		specified.
<io_addr>	Is base I/O address set on your network interface card.
		The default address of 0x300 is used, if this parameter is not
                specified.


2. Parameters for INSTALL utility:
DCD16.EXE
    DCD16.EXE is an integration version of open adapter utility.
    DCD16.EXE supports Intel 82365SL, Toshiba T3300SL's ICCNT, and Socket
    Services v1.01, v2.0, v2.01, v2.10 Card Services v2.0, v2.01, v2.10.

   DEVICE = DCD16.EXE [/iop:P0] [/irq:P1] [/slt:P2]

   Parameter description:
	/iop   :I/O base
	/irq   :IRQ value
	/slt   :Slot number

	P0 :The selectable window I/O base with 0x20 range.
	    The default value is 0x300.
	P1 :The selectable irq value.
	    The default value is 0x5.
	P2 :The selectable slot number.
	    The default value is 0. You must set 0 when you use slot 1.
	    Set slt:1 when slot 2 is used,etc.