Server Driver for NetWare 3.12

   Introduction:
   -------------
   This document describes the procedure to install the NetWare v3.12
   server driver for PCI Ethernet adapter.


   Location of Driver:     \NETWARE\SERVER\312\PCISRV.LAN


   Installation Procedure:
   -----------------------
      Before you start the installation  process,  make sure that
      the Novell NetWare 386 v3.12 server is properly installed.
      Similarly, your adapter should also be properly installed in your
      server.

      1. These files can be obtained from this driver disk subdirectory
         A:\NETWARE\SERVER\312

         MSM31X.NLM
         ETHERTSM.NLM

      2. Log into  the server as a  supervisor,  copy all PCISRV.LAN
         related  files from this  Driver  Diskette  subdirectory
         A:\NETWARE\SERVER\312 into the NetWare 386 subdirectory SYSTEM
         of your server. (If some files exists, rename the  existing
         files in the SYSTEM subdirectory.)

      3. When the NetWare 386 prompt appears (indicated by a colon),load
         your server driver. Simply type:

         : LOAD LSLENH <Enter>
         : LOAD PCISRV <Enter>

         or, you can directly load file from the driver disk :

         : LOAD A:\NETWARE\SERVER\311\LSLENH <Enter>
         : LOAD A:\NETWARE\SERVER\311\PCISRV <Enter>

      4. Bind IPX to the adapter driver. At the NetWare server prompt
         ,type:

         :BIND IPX TO PCISRV <Enter>

      5. After you press <Enter>, the computer prompts you the Network
         Number. For details on how to assign this number, please refer
         to your NetWare 386 Installation Manual.


      6. Add the load and bind statements you require to the server's
         AUTOEXEC.NCF file so that the LAN driver will be loaded
         automatically once the server starts up.


   NOTES:
   ------
      1. Installing Multiple LAN Adapters:
         If  you  have  multiple  LAN  adapters in a single server, each
         adapter  must  have a  different network  number.  You may also
         want to name each adapter for ease of management. For example:

         LOAD PCISRV EtherID=0000B4000001 FRAME=Ethernet_802.2 NAME=LAN_A
         BIND IPX TO LAN_A NET=11
         LOAD PCISRV EtherID=0000B4000002 FRAME=Ethernet_802.3 NAME=LAN_B
         BIND IPX TO LAN_B NET=22

         (The keyword, EtherID, is the ethernet ID of a adapter. This
         keyword is provided for multiple  LAN cards in a single server by
         PCISRV.LAN driver.  If "EtherID" is unknown, you can ignore it and
         directly  LOAD  under  the  server prompt,  then the screen will
         display every adapter ethernet address).

      2. Installing One LAN adapter with Multiple Frame Types:
         When  binding multiple frame types to one adapter, enter a LOAD
         and BIND statement for each frame type. Each LOAD statement will
         use a different network number is required on the bind statement.
         You need  to supply  a name on each load line in order to avoid
         being  prompted  for which  board to bind IPX to. If you do not
         have the name option in the AUTOEXEC.NCF , it will not  execute
         completely without user intervention.  Example:

           LOAD C:\PCISRV FRAME=ETHERNET_802.3 NAME=IEE8023
           BIND IPX TO IEE8023 NET=11111
           LOAD C:\PCISRV FRAME=ETHERNET_802.2 NAME=IEE8022
           BIND IPX TO IEE8022 NET=22222

   If any problem occurs during the binding process, the screen will display
   the  error  messages.  Please refer to your NetWare 386 manual for
   details on these messages.