Remote boot to Windows NT server

   Introduction:
   -------------
   This document describes the procedures to install RPL server on Windows
   NT server.


   Install the NT server 3.5, 3.51 RPL server:
   ------------------------------------------
   1. Install the Remoteboot Service on the NT Server.

   1.1 Choose Control Panel, Network, Add Software, Remoteboot Service,
       put NT server CD or disk, to install Remoteboot Service.

     Note:
       To install RPL server, you must install DLC and NetBEUI protocols
       in your NT server first.

   2. Install MS-DOS Files for Remoteboot workstation.

      Copy all the MS-DOS 6.22 files to
			   ----> \\systemroot\RPL\RPLFILES\BINFILES\DOS622
	 copy c:\dos\*.* \\systemroot\RPL\RPLFILES\BINFILES\DOS622
	 attrib -s -h c:\io.sys
	 attrib -s -h c:\msdos.sys
	 copy c:\io.sys \\systemroot\RPL\RPLFILES\BINFILES\DOS622
	 copy c:\msdos.sys \\systemroot\RPL\RPLFILES\BINFILES\DOS622
	 attrib +s +h c:\io.sys
	 attrib +s +h c:\msdos.sys

   3. Create Remoteboot configuration for new adapter

   3.1 Copy the MS-DOS device driver(NDIS2) for the Ethernet adapter to the
       \\systemroot\RPL\BBLOCK\NDIS directory.
       for example: PCIND.DOS NDIS2 driver for the PCI adapter.

   3.2 Create the directory  \\systemroot\RPL\BBLOCK\NETBEUI\PCI  and
       create  PCI.CNF,  PROTOCOL.INI  files in this directory.   The
       templates for PCI.CNF and PROTOCOL.INI are stored at the \BOOTROM
       directory in this driver diskette.

	Sample for PCI.CNF:

	  ; DOS on PCI Ethernet
	  BASE D0H
	  RPL BBLOCK\RPLBOOT.SYS
	  LDR BBLOCK\RPLSTART.COM ~
	  DAT BBLOCK\NETBEUI\PCI\PROTOCOL.INI
	  DRV BBLOCK\RPLDISK.SYS ~ ~ ~
	  EXE BBLOCK\RPLPRO1.COM ~ 2 ~
	  EXE BBLOCK\I13.COM ~ ~ ~
	  EXE BBLOCK\RPLBIND2.EXE ~ ~
	  EXE BBLOCK\PROTMAN.EXE ~ ~
	  EXE BBLOCK\RPLBIND1.EXE ~ ~
	  ;DRV BBLOCK\IPXNDIS.DOS ~ ~ ~
	  ;DRV BBLOCK\TCPDRV.DOS /I:C:\LANMAN.DOS ~ ~
	  EXE BBLOCK\NETBEUI\NETBEUI.EXE ~ 10 ~
	  DRV BBLOCK\NDIS\PCIND.DOS ~ ~ ~
	  DRV BBLOCK\PROTMAN.DOS /I:C:\LANMAN.DOS ~ M

	Sample for PROTOCOL.INI:

	  [protman]
	    drivername = protman$
	    dynamic = yes
	    priority = netbeui

	  [netbeui_xif]
	    drivername = netbeui$
	    bindings = pci_nif
	    names = 6
	    ncbs = 12
	    packets = 20
	    pipeline = 10
	    sessions = 6
	    stacksize = 512
	    lanabase = 0

	  [xnsnb_xif]
	    drivername = xnsnb$
	    bindings = pci_nif
	    load = xnsnb[cbr]
	    lanabase = 1

	  [xnstp_xif]
	    drivername = xnstp$
	    bindings = pci_nif
	    load = xnstp[ub]
	    lanabase = 1

	  [tcpip_xif]
	    drivername = TCPIP$
	    disabledhcp = (TCPIP_NO_DHCP)
	    ipaddress0 = (TCPIP_ADDRESS)
	    subnetmask0 = (TCPIP_SUBMASK)
	    defaultgateway0 = (TCPIP_GATEWAY)
	    tcpsegmentsize = 1450
	    tcpwindowsize = 1450
	    nbsessions = 6
	    load = tcptsr[c],tinyrfc[c],emsbfr[cr]
	    unload = "unloadt /notsr[dc]"
	    bindings = pci_nif
	    lanabase = 1

	  [ipx_xif]
	    drivername = ipx$
	    load = ipxmark[u],ipx[u]
	    unload = ipxrel[c]
	    bindings = pci_nif
	    lanabase = 1

	  [msdlc_xif]
	    drivername = msdlc$
	    bindings = pci_nif
	    load = msdlc[ub]
	    unload = msdlc[u]

	  [pci_nif]
	    drivername = PCIND$

   3.3 Use RPLCMD utility to add a bblock record for new adapter.

       Under MS-DOS Prompt, type <1>. NET START RemoteBoot
				 <2>. RPLCMD

   3.4 You should follow the direction displayed on the screen.

	  Adapter Boot Config Profile Service Vendor Wksta [Quite] V
	  Add Del Enum: A
	  VendorName=0000B4
	  VendorComment=

	  Adapter Boot Config Profile Service Vendor Wksta [Quite] B
	  Add Del Enum:A
	  BootName=DOSX
	  VendorName=0000B4
	  BbcFile=BBLOCK\NETBEUI\PCI\PCI.CNF
	  BootCommet=Name of this adapter
	  WindowsSize=0

	  Adapter Boot Config Profile Service Vendor Wksta [Quite] C
	  Add Del Enum:A
	  ConfigName=DOS622X
	  BootName=DOSX
	  DirName=DOS
	  DirName2=DOS622
	  FitShared=FITS\DOS622.FIT
	  FitPersonal=FITS\DOS622P.FIT
	  ConfigComment=DOS 6.22 <Adapter name>
	  DirName3=
	  DirName4=

   3.5 Shutdown Windows NT server, and reboot it.

   4. Login to NT server as Administrator.

   5. Start RemoteBoot service and Remoteboot manager

   5.1 Under MS-DOS Prompt, type "NET START Remoteboot"

   5.2 In Network administrator, Remoteboot Manager
	1.Choose Remoteboot, New Profile, to create an PCI Profile Name.
	2.Add new workstation for this Ethernet adapter and choose PCI
	  Profile file.

    Note:
	If the Node ID of workstation does not match with your Profile file,
	you can use "Convert Adapters" in Remoteboot menu of Remoteboot
	Manager to configure or cteate the Profile file.