****************************************************************************** * Genius LAN GF100TXRIII Series Fast Ethernet Card IBM LAN Server driver * ****************************************************************************** LAN Server 2.0/3.0 Introduction: ------------- This document describes the procedure to install NDIS driver on DOS LAN Requester and OS/2 LAN server 2.0 (or 3.0) for Genius LAN GF100TXRIII Series Fast PCI ethernet adapter. Location of Driver: \LANSRVR\DOS\RTSND.DOS (for DOS LAN Requester) \LANSRVR\OS2\RTSND.OS2 (for OS/2 LAN Server) Installing driver procedure on DOS LAN Requester : -------------------------------------------------- 1. Insert the IBM LAN Support Program (LSP) Version 1.30 (or 1.31) Diskette into your floppy drive A: . 2. Type A:\dxmaid and press . 3. The screen will display the IBM logo. Press twice until the "Environment Information" appears on screen. 4. Responds to the screen prompts, specifying the following values for each field,use the to toggle between choices: Configuration for this computer? Yes Use existing configuration information? Yes Do you have adapter option diskettes? Yes Are you configuring for two adapters? No Do you need 802.2 interface support? Yes Source for LSP A:\ Target for new configuration C:\LSP Make sure that the values given above are correct, then press to store your choices. 5. Insert the Genius LAN GF100TXRIII driver diskette in floppy A,and specify your pathname A:\LANSRVR\DOS,then press ENTER. 6. Follow screen instructions to complete the process. Simply pressing for each screen display will select the default options. Press until you reach the display prompting you to insert the LSP diskette. 7. Insert the LSP diskette as prompted. Press to acknowledge completion of the action. 8. A screen showing the current configuration detected will be displayed. It should show the Genius LAN GF100TXRII adapter and the protocols already selected (i.e., "IBM IEEE 802.2" and "IBM OS/2 NETBIOS"). 9. Press . to save the new configuration. This completes the LSP installation. 10. Save the configuration and reboot your computer. 11. Insert the DOS LAN Requester Install Diskette 1 into your floppy drive. 12. Type A:\INSTALL 13. The IBM logo will again appear on the screen. Press to move on to the next screen. 14. Follow screen instructions, pressing to move from screen-to-screen until you are prompted to indicate the pathname of the DOS LAN Requester directory (C:\DOSLAN ). 15. Specify the pathname (C:\DOSLAN is the default) for the DOS LAN Requester directory . Then press to continue. 16. The program will ask you for the services that you require. 17. Highlight the appropriate option. Select either "Send messages" or "Send, View, Edit, and Log message" option. (Normally, second option "Send, View, Edit and Log message" is selected). 18. Specify the PC's ID and domain ID. 19. Follow screen prompts to complete the installation. Installing driver procedure on OS/2 LAN Server 2.0/3.0 : ------------------------------------------------------ Before you start with the installation process, make sure that OS/2 LAN Server is properly installed. Similarly, your adapter should also be properly installed in your server. 1. Copy RTSND.OS2 and RTL8139.NIF files from your Driver diskette (\LANSRVR\OS2) to C:\IBMCOM\MACS. 2. Click the OS/2 LAN Service icon. 3. Select "Installation and configuration". The IBM logo should appear onscreen. 4. Click . 5. Select and press . 6. Select "Install or Configuration this Workstation." 7. Select server type, adding a server or domain controller. The "install or remove" selections should appear. 8. Select "Configure a component." 10. Click the "Configure" button. 11. Select "Configure workstation." 12. Select "GF100TXRIII Fast ethernet adapter" when prompted to identify you Network Adapter. Then click the button. 13. Select IBM NETBIOS from the list and click the button. 14. Select to confirm all selections. 15. Follow screen instructions to complete the process, selecting to accept default selections. 16. Continue pressing until your screen prompts you to backup old CONFIG.SYS and AUTOEXEC.BAT and create a new CONFIG.SYS and AUTOEXEC.BAT. Also select to confirm this. 17. Installation is complete now. Reset your PC by turning it off and on. Note: ----- 1. The DOS version must be bellow DOS 5.0 when install DOS LAN requester into your system. 2.sample protocol.ini: [RTL8139] DriverName=RTSND$ EtherID=@52544C111111 ;This keyword is used to desinate a GF100TXRIII ;adapter by assigning it's ethernet ID ;when more than one adapters exist on one ; system. BusNo=@00 ;This keyword is used to desinate a GF100TXRIII ;adapter by assigning it's PCI bus number ;when more than one adapters exist on one ; system.(must be used with 'DeviceNo' keyword) DeviceNo=@0A ;This keyword is used to desinate a GF100TXRIII ;adapter by assigning it's PCI Device number ;when more than one adapters exist on one ; system.(must be used with 'BusNo' keyword) Speed= 100/10 ;This keyword is used to force GF100TXRIII adapter ;to speed 10M or 100M mode. If not present, ;the driver will auto-detect the speed. -- KYE System Corp -- LAN Server 4.0 [1].Introduction: ------------- This document describes the procedure to install NDIS driver on DOS LAN Requester and OS/2 LAN server 4.0 for Genius LAN GF100TXRIII Ethernet adapter. Location of Driver: \LANSRVR\DOS\RTSND.DOS (for DOS LAN Services) \LANSRVR\OS2\RTSND.OS2 (for OS/2 LAN Server) [2].Installing driver procedure on DOS LAN Requester : -------------------------------------------------- Before you start with the installation process, make sure that DOS LAN Services is properly installed. Similarly, your adapter should also be properly installed in your client PC. 1. Copy RTSND.DOS from your Driver diskette (A:\LANSRVR\DOS) to DOS LAN Services subdirectory C:\DLS . 2. Under DOS LAN Requester subdirectory C:\DLS, run INSTALL 3. The screen display some description. If it's correct, move highlight to "The listed options are correct" item ,then press ENTER. 4. Move highlight to "Network Card", then press ENTER. 5. Select "Change driver for network card." item, then press ENTER. 6. Select "Network card not shown in list below..", then press ENTER. 7. Insert the Genius LAN GF100TXRIII driver diskette in floppy A,and specify your pathname A:\LANSRVR\DOS,then press ENTER. 8. Genius LAN GF100TXRIII driver is now installed on your computer, reboot your computer. [3].Installing driver procedure on OS/2 LAN Server 4.0: --------------------------------------------------- Before you start with the installation process, make sure that OS/2 LAN Server is properly installed. Similarly, your adapter should also be properly installed in your server. 1. In OS/2 window, Click the "MPTS" icon. 2. The screen will display the IBM Log, press "OK". 3. Select "Install" button. 4. Insert the Genius LAN GF100TXRIII driver diskette, specify the driver path A:\LANSRVR\OS2 and press . 5. When complete above step to load RTSND.OS2 into OS/2 system, then configure your system. 6. The same step as step 3, select "Configure" button. 7. The screen will display "Configure" dialog box and select "LAN adapters and protocols" then press "configure" button. 8. The screen will display "LAPS Configuration" dialog box, move highlight to "GF100TXRIII Fast PCI Ethernet Adapter" item in "Network Adapter" window, and select "NetBios" protocol. Press "OK". 9. Installation is complete now. Reset your PC by turning it off and on. [4].Installing Multiple LAN Adapters: ---------------------------------- 1.follow [3]. 1-9 and add tow GF100TXRIII Adapter driver 2.in IBM Lan Services icon, OS/2 Lan Sercices Installation /Configuration Select your the server of the insatlled,[OK]. Do you want to re-install this version.[No]. Installing tow card driver [OK] in mpts. Configure a component. [OK] Lan Services Adapters. [OK] Configure. [OK] Two Adapter [V]. OK [5].A sample PROTOCOL.INI file: ------------------------------- [RTL8139] DriverName=RTSND$ EtherID=@52544C111111 ;This keyword is used to desinate a GF100TXRIII ;adapter by assigning it's ethernet ID ;when more than one adapters exist on one ; system. BusNo=@00 ;This keyword is used to desinate a GF100TXRIII ;adapter by assigning it's PCI bus number ;when more than one adapters exist on one ; system.(must be used with 'DeviceNo' keyword) DeviceNo=@0A ;This keyword is used to desinate a GF100TXRIII ;adapter by assigning it's PCI Device number ;when more than one adapters exist on one ; system.(must be used with 'BusNo' keyword) Speed= 100/10 ;This keyword is used to force GF100TXRIII adapter ;to speed 10M or 100M mode. If not present, ;the driver will auto-detect the speed. -- KYE Systems Corp --