Apr. 1995
3Com 3+ Share Driver Installation/
FTP PC/TCP Installation/
PC-NFS Driver Installation
for
D-Link DE-621 Duplex and DE-620
==================================
Thank you for purchasing the D-Link Duplex for desktop, laptop
and notebook PCs to retain DE-620 and printer or key card connection.
Before you installing driver program, please refer to DE-620 or DE-621
manual to get more detail installation. A simple installation is as the
following figure.
ÄÄÄÄ
/ /ł
/ / ł
/ / *ł<------- connect to DE-620 only
ÚÄÄÄÄż * ł
connect |\ ł ł* *ł<------- connect to printer or
to pc |.| ÚÄÄÄŮ ł * / key card
printer <-- |.|ÍÍÍÍÍÍÍÍÍÍł DE-621 ł* /
port |.| ł ł /
|/ ŔÄÄÄÄÄÄÄÄŮ
Note: DE-620 series product cannot Ping to server when it works with
IBM PS/VP.
***********************************************
How to install DE-620 with 3Com 3+ Share driver
***********************************************
The D-Link 3COM 3+ Share Driver Program lets you run 3Com 3+ Share
on your PC with the D-Link Ethernet Pocket LAN Adapter.
The following files will be used in this installation:
Files Contents
----------- -------------------------
DE620PD.SYS DE-620 Driver Program
ETH.SYS 3Com 3+ Share Driver
1. Follow the installation procedure for 3Com EtherLink board.
2. Copy the program ETH.SYS from the Installation Diskette for
the D-Link Ethernet Pocket LAN Adapter to the boot disk/diskette.
This program will replace the program of the same file name
(ETH.SYS) when you perform the installation procedure in step 1
above.
3. In the CONFIG.SYS file on the boot disk/diskette, make sure
you have the following two statements. The order of these two
statement must be as shown below.
DEVICE = DE620PD.SYS <packet_int_no>
DEVICE = ETH.SYS
You may now boot and start your 3COM workstation.
Notes:
<packet_int_no> is the software interrupt vector number used by the
packet driver program, which can be from 96 to 128.
*************************************
How to install DE-620 with FTP PC/NFS
*************************************
The following files will be used in this installation:
Files Contents
----------- ----------------------------------------------------------
PDNFS.SYS PC-NFS Driver Program
DE620PD.SYS Packet driver program for DE-620 card
DE620PD.COM Packet driver program for DE-620 card
Two methods can be used to install:
METHOD 1:
1. Install the PC-NFS program according to the procedure described in the
PC-NFS manual. On the screen of the PC-NFS install program, select 3C501
(the 3Com EtherLink card) as your network interface card. When the screens
prompt you, select 3 for the interrupt level (IRQ), and select 300h for
the base I/O address.
2. Copy the following files to the \NFS directory of your hard
disk:
PDNFS.SYS
DE620PD.SYS
DE620PD.COM
3. Modify the CONFIG.SYS file as follows:
DEVICE=C:\ANSI.SYS
DEVICE=C:\NFS\PCNFS.SYS /m
DEVICE=C:\NFS\SOCKDRV.SYS
DEVICE =C:\NFS\DE620PD.SYS <packet_int_no>
DEVICE=C:\NFS\PDNFS.SYS
LASTDRIVE=V
AUTOEXEC.BAT file:
SET PATH = C:\; C:\NFS
SET TZ=EST5EDT
SET NFSDRIVE = C
NET YPDOMAIN ypserver
NET START RDR
NET YPSET homer
NET NAME john
NET USER F: \\user\john
We use the name "john" here as an example.
Notes:
<packet_int_no> is the software interrupt vector number used by the packet
driver program, which can be from 96 to 128.
4. Reboot the PC to start PC-NFS.
You may now execute the PC-NFS commands to communicate
other computers through the TCP/IP protocol.
METHOD 2:
1. Install the PC-NFS program according to the procedure described in the
PC-NFS manual. On the screen of the PC-NFS install program, select 3C501
(the 3Com EtherLink card) as your network interface card. When the screens
prompt you, select 3 for the interrupt level (IRQ), and select 300h for
the base I/O address.
2. Copy the following files to the \NFS directory of your hard
disk:
PDNFS.SYS
DE620PD.SYS
DE620PD.COM
3. Modify the CONFIG.SYS file as follows:
DEVICE=C:\ANSI.SYS
DEVICE=C:\NFS\PCNFS.SYS /m
DEVICE=C:\NFS\SOCKDRV.SYS
DEVICE=C:\NFS\PDNFS.SYS
LASTDRIVE=V
AUTOEXEC.BAT file:
SET PATH = C:\; C:\NFS
SET TZ=EST5EDT
SET NFSDRIVE = C
DE620PD <packet_int_no>
NET YPDOMAIN ypserver
NET START RDR
NET YPSET homer
NET NAME john
NET USER F: \\user\john
We use the name "john" here as an example.
Notes:
<packet_int_no> is the software interrupt vector number used by the packet
driver program, which can be from 96 to 128.
4. Reboot the PC to start PC-NFS.
You may now execute the PC-NFS commands to communicate
other computers through the TCP/IP protocol.
*************************************
How to install DE-620 with FTP PC/TCP
*************************************
Thank you for purchasing the D-Link Duplex for desktop, laptop
and notebook PCs to retain DE-620 and printer or key card connection.
Before you installing driver program, please refer to DE-620 or DE-621
manual to get more detail installation. A simple installation is as the
following figure.
ÄÄÄÄ
/ /ł
/ / ł
/ / *ł<------- connect to DE-620 only
ÚÄÄÄÄż * ł
connect |\ ł ł* *ł<------- connect to printer or
to pc |.| ÚÄÄÄŮ ł * / key card
printer <-- |.|ÍÍÍÍÍÍÍÍÍÍł DE-621 ł* /
port |.| ł ł /
|/ ŔÄÄÄÄÄÄÄÄŮ
The following files will be used in this installation:
Files Contents
----------- ---------------------------------
DE620PD.SYS DE-620 series Driver Program
DE620PD.COM DE-620 series Driver Program
The D-Link packet driver programs above let you run FTP's PC/TCP
with the D-Link DE-620 series Ethernet Card. Two methods can be used:
METHOD 1:
If you use the DE620PD.SYS program, the following statement must
be included in your CONFIG.SYS file:
DEVICE = DE620PD.SYS <packet_int_no>
This statement may be placed anywhere in the CONFIG.SYS file.
METHOD 2:
If you use the DE620PD.COM program, follow the procedure below:
1. Execute the DE620PD.COM as follows:
>DE620PD <packet_int_no>
2. Execute the ETHDRV.EXE device driver program (provided by
FTP).
You are now ready to use FTP's PC/TCP.
Notes:
<packet_int_no> is the software interrupt vector number used by the packet
driver program, which can be from 96 to 128.