0001:02*60 * Program already loaded in memory * * Type exit to return to the program * 0002:03*60 * Cannot execute COMMAND.COM * * Not enough memory or program not found * * Hit Enter key to continue * 0003:04*60 * Memory allocation error * * Less memory reallocated after return from DOS * * You have invoked a program still resident in memory * * Hit Enter key to EXIT * 0004:02*60 * Hit Enter key to confirm EXIT * * Hit any other key to resume * 0005:04*60 * Warning: This program resides in testing memory area * * This testing is skipping part(s) of base memory segment * * To test all - User should unload all resident programs * * Hit any key to resume * 0600:02*60 * Configuration file loaded * * Hit ENTER key to continue * 0610:02*60 * Specified file is not a configuration file * * Hit ENTER key to continue * 0620:02*60 * Unable to read configuration file * * Hit ENTER key to continue * 0700:02*60 * Configuration file saved * * Hit ENTER key to continue * 0705:03*60 * Configuration unchanged * * File not modified * * Hit ENTER key to continue * 0710:02*60 * Unable to create configuration file * * Hit ENTER key to continue * 0720:02*60 * Unable to save configuration file * * Hit ENTER key to continue * 0800:02*60 * Invalid Port Address * * Hit ENTER key to continue * 0810:03*60 * Gap detected between base and extended memory. You may * * want to reconfigure your existing memory board to avoid * * the gap. Hit ENTER key to continue. * 0811:02*60 * ERROR: EMS I/O ports can NOT be reassigned * * Hit Enter key to continue * 0814:05*60 * WARNING: The memory on this board is not fully utilized. * * You may increase extended and/or expanded EMS * * memory. * * ENTER 'y' IF YOU WANT TO IGNORE THIS MESSAGE, * * OTHER KEYS TO RECONFIGURE THE SETTINGS. * 0815:06*60 * WARNING: Only 8 megabytes (8192 KB) will be allocated * * to EMS at most. You may reconfigure your * * extended memory size to avoid a waste of * * memory on this board. * * ENTER 'y' IF YOU WANT TO IGNORE THIS MESSAGE, * * OTHER KEYS TO RECONFIGURE THE SETTINGS. * 0816:03*60 * ERROR: No memory left for EMS. The system turns off all * * the EMS ports which you have selected already. * * Hit ENTER key to continue * 0817:04*60 * ERROR: Only one EMS port is available in the current * * configuration. The system turns off the * * EMS ports which are not used at the moment. * * Hit ENTER key to continue * 0818:04*60 * ERROR: Only two EMS ports are available in the * * current configuration. The system turns off * * the EMS ports which are not used at the moment. * * Hit ENTER key to continue * 0819:04*60 * ERROR: Only three EMS ports are available in the * * current configuration. The system turns off * * EMS Port 4 at the moment. * * Hit ENTER key to continue * 0820:04*60 * ERROR: Requested memory exceeds available memory * * Please add more memory banks * * or lower the amount of requested memory * * Hit ENTER key to continue * 0821:03*60 * ERROR: Please specify sequential EMS port addresses * * for each adjacent 2MB block of expanded memory. * * Hit ENTER key to continue * 0830:04*60 * ERROR: The total amount of extended memory * * (previously added and currently adding) * * may not exceed 15232K bytes * * Hit ENTER key to continue * 0835:07*60 * This memory diagnostic will DESTROY all data in the EMS. * * If you have already installed the EMM.SYS driver in the * * CONFIG.SYS, you must reboot your system after the * * diagnostic to re-install the EMM.SYS. * * * * Enter 'y' if you want to conduct the test, or any other * * key to exit. * 0840:02*60 * EMS port test failed * * Hit ENTER key to continue * 0850:02*60 * All conventional memory are used up * * Hit ENTER key to continue * 0855:02*60 * No memory allocated for testing * * Hit ENTER key to continue * 0860:03*60 * Memory test completed * * No bad chips detected * * Hit ENTER key to continue * 0870:03*60 * Memory test completed * * Blinking bars designate bad chips * * Hit ENTER key to continue * 0880:02*60 * Unable to go to protected mode for testing * * Please reboot your system * FFFF:01*03 EOF