Empire 1400/2100S


   Jumper    Setting Description                      

  TE / J14     OFF   Termination disabled             
               ON    Termination enabled              

     EP        OFF   Parity checking disabled         
               ON    Parity checking enabled          

     WS        OFF   Wait/spin disabled               
               ON    Wait/spin enabled                

     SS        OFF   Self Seek disabled               
               ON    Self Seek enabled                

    A2, A1,     -    These jumpers are used in        
     A0              combination to determine the     
                     drive's SCSI ID [See table 2]    

     PF        OFF   Not used, factory only, leave    
                     open.                            

    J13        ON    SCSI termination power from      
               OFF   drive.                           
                     SCSI termination power from      
                     Host                             

Table 1

Termination Enable (TE) Jumper

One of the requirements of the SCSI bus is that it be properly terminated. If more than one SCSI device is connected to the host, only the last device must be terminated. The Terminator Enable (TE) jumper, when installed, enables an active termination circuit, thereby terminating the SCSI bus. With the TE jumper removed, bus termination is disabled.

At the factory, Quantum configures the Empire 1400/2100 hard disk drive with termination enabled; that is, with a jumper installed across the pins labeled TE. To disable termination, remove the jumper from the TE pins. In addition the Empire 1400/2100 utilizes a pair of terminating resistor packs, these must be installed when termination is enabled; that is, with the jumper TE installed the terminating resistors must be in place. With termination disabled the resistor packs must be not be in place; that is, when the TE jumper is removed the terminating resistors must be removed.

Note: There are no Termination Resistor Packs to remove on the Empire 2100S drive with the new Rev.4 PCB. [New Style]

Enable Parity (EP) Jumper

The Enable Parity (EP) jumper controls parity checking of data across the SCSI bus. With parity checking enabled, the drive performs parity checking. With parity checking disabled, the drive continues to generate parity information, but does not perform parity checking.

At the factory, Quantum configures the Empire 1400/2100 hard disk drive with parity checking enabled; that is, with a jumper installed across the pins labeled EP. To disable parity, remove the jumper from the EP pins.

Wait /Spin (WS) Jumper

With the Wait/Spin (WS) jumper disabled, at power on or reset, the drive motor starts to spin automatically, and the drive prepares itself to perform read or write operations without the need for a start command. At a power on or reset, with the Wait/Spin jumper enabled, the host must send a START/STOP UNIT command to activate the drive motor for read or write operations. In addition, with the W/S jumper enabled, the drive performs power sequencing to prevent an overload of the host's power supply due to simultaneous, peak start-up current demands from multiple devices.

At the factory, Quantum configures the Empire 1400/2100 hard disk drive with the Wait/Spin jumper disabled; that is, without a jumper installed across the pins labeled WS. To enable Wait/Spin, install a jumper across the pins labeled WS.

PF Jumper

This is not used in the field and should be open, ignore this jumper.

Self Seek Jumper

With the Self Seek jumper enabled the drive performs, at power on, a continuous seek diagnostic. This diagnostic will not terminate until: 1) Power is removed, 2) SS jumper removed.

At the factory, Quantum configures the Empire 1400/2100 hard disk drive with the Self Seek jumper disabled; that is, without a jumper installed across the pins labeled SS. To enable Self Seek, install a jumper across the pins labeled SS.

SCSI-Bus Device Identification (A0 - A2) Jumpers

Used in combination, the jumper settings across pins A2, A1 and A0 determine the Empire 1400/2100 hard disk drive's SCSI-bus device I.D. By default, Quantum configures the drive with a SCSI ID of 6; that is, with jumpers installed across the pins labeled A2 and A1, and no jumpers installed across pins labeled A0.

To assign a different SCSI ID, change the jumper settings as shown in Table 2.

Note: That some drives have an additional ID position of A3, this is not currently used on the narrow or 50 pin drive. Please ignore this setting, please leave open. In addition, the A3 jumper is removed on the Empire 1400/2100S Rev. 4 PCB. [New Style]


   A2        A1        A0      SCSI ID  

   OFF       OFF       OFF        0     
   OFF       OFF       ON         1     
   OFF       ON        OFF        2     
   OFF       ON        ON         3     
   ON        OFF       OFF        4     
   ON        OFF       ON         5     
   ON        ON        OFF        6     
   ON        ON        ON         7     

Table 2

J13 Termination Power Jumper

When enabled this jumper supplies +5vdc termination power from the drive to the SCSI bus. With this jumper removed the SCSI bus must supply termination power.

At the factory, Quantum configures the Empire 1400/2100 hard disk drive with the J13 jumper enabled; that is, with a jumper installed across the pins labeled J13. To disable Termination Power supply from the disk drive, remove the jumper across the pins labeled J13.

Alternate Address Connector (J12)

The drive's Alternate Address Connector is mounted on the front edge of the drives PCB assembly, near the LED connector. Please refer to table 3 for connector definitions.


      Pin          Signal Name    

       1              Ground      
       2                A2        
       3                A1        
       4                A0        
       5           Not Defined    

Table 3

The recommended header connector includes:

Berg Electronics

- Connector housing / 5 position P/N 51021-0500 or equivalent [Alternate Address connector]

- Connector housing / 2 position P/N 51021-0200 or equivalent [LED connector]

- Contact Pins P/N 50679-8000 (26 to 30 AWG) or equivalent


Copyright 1995 Quantum Corporation
500 McCarthy Blvd, Milpitas, CA 95035
408-894-4000
We are always interested in any suggestions you might have regarding this service.
Note: Some files are available in PDF Format.