QUICK INSTALLATION GUIDE IDE/AT Conner drives are * low level * formatted at the factory. It is only necessary to run SETUP, FDISK and DOS FORMAT. Model Hds Cyls Sec Pcomp L-Zone Type Table LED CP2034 2 823 38 0 823 *UT 3 n/a CP2064 4 823 38 0 823 *UT 3 n/a CP2084 8 548 38 0 548 *UT 3 n/a CP2124 8 560 53 0 560 *UT 3 n/a CP3184 6 832 33 0 832 *UT 1 A CP3104 8 776 33 0 776 *UT 1 A CP3204 16 683 38 0 683 *UT 2 B CP30064 4 762 39 0 762 *UT 2 B CP30084 8 526 39 0 526 *UT 2 B CP30104 8 762 39 0 762 *UT 2 B CP30084E 4 903 46 0 903 *UT 3 C CP30174E 8 903 46 0 903 *UT 3 C CP30204 16 683 38 0 683 *UT 3 C CP3304 16 659 63 0 659 *UT 3 D CP3364 16 702 63 0 702 *UT 3 D CP3504 16 987 63 0 987 *UT 3 D CP3544 16 1024 63 0 1024 *UT 3 B Table 1 jumper settings: Single drive = Jumper ACT and C/D Master drive = Jumper ACT, C/D and DSP. Slave drive = No jumpers installed. Table 2 jumper settings: Single drive = Jumper C/D Master drive = Jumper C/D & DSP Slave drive = No jumpers installed. Table 3 jumper settings: Single and Master drive = Jumper C/D Slave drive = no jumper ALL CONNER 20 MBYTE DRIVES USE DRIVE TYPE 2. ALL CONNER 40 MBYTE DRIVES USE DRIVE TYPE 17. * UT = Universal translate. Select a drive type that is close to, but does not exceed the megabyte capacity of the drive. The drive will translate to the megabyte capacity you have selected. LED A: J-4 B: J-1 C: J-5 D: J-3 Pin 1=+ Pin 3=+ Pin 3=+ Pin 3=+ Pin 2=- Pin 4=- Pin 4=- Pin 4=- QUICK INSTALLATION GUIDE SCSI Most SCSI host adapters are compatible with Conner drives. Software drivers and installation instructions are provided with the host adapter. The drives are shipped with SCSI ID set to 7. To select a different ID refer to the following: Table A Table B ID E-1 E-2 E-3 ID E2 E3 E4 0 out out out 0 out out out 1 in out out 1 in out out 2 out in out 2 out in out 3 in in out 3 in in out 4 out out in 4 out out in 5 in out in 5 in out in 6 out in in 6 out in in 7 in in in 7 in in in Parity is always ENABLED on the CP3200,CP30060,CP30080,CP30100. All other models, jumper E-4 to disable parity. SCSI drive parameters: Model Hds Cyl Sec Table LED CP2020 2 642 32 A n/a CP340 4 788 26 B 1 CP3020 2 622 33 A 1 CP3040 2 1026 40 A 1 CP3180 6 832 33 A 1 CP3100 8 776 33 A 1 CP30060 2 1524 39 A 2 CP30080 4 1053 39 A 2 CP30100 4 1522 39 A 2 CP30200 4 2119 49 A 2 CP3200 8 1366 38 A 2 CP3360 8 1806 49 A 2 CP3540 12 1806 49 A 2 LED 1 LED 2 J-4 Pin 1 = + J-1 Pin 3 = + Pin 2 = - Pin 4 = - CONTACT YOUR LOCAL DISTRIBUTOR FOR TECHNICAL ASSISTANCE Revised : 28/9/91@20:14EST (Some drives have a translation mode which gives them a virtual configuration different to their physical configuration. This is to make the parameters lie within the BIOS limits -- 1024 cyls, etc) Physical configuration. Translation Mode Model cap. Cyl Heads Sec/trk Cyl Heads Sec/trk CP3024 21M 636 2 33 615 4 17 CP3044 43M 1047 2 40 977 5 17 CP30064 60M 1522 2 39 761 4 39 CP3184 84M 832 6 33 832 6 33 CP3104 104M 776 8 33 776 8 33 CP3114 112M 832 8 33 832 8 33 CP30104 120M 1522 4 39 756 8 39 CP3204F 212M 1366 8 38 683 16 38 CP3504 510M 1695 12 49 847 24 49 Note: From my experience, its possible to use these drives in virtual configurations different from both the physical config and the standard 'translation mode'. e.g., I have used a CP3184 configured as 10 head, 965 cyl, 17 sec/cyl, and a CP3104 configured as 10 head, 1225 cyl, 17 sec/cyl. Jumper settings. ('J' => jumper installed, '-' => no jumper installed) Jumper Description 1-Drive 2-Drives Master Slave CP3024, CP3044, CP3184, CP3104, CP3114 ACT J - - DSP - J - C/D J J - HSP - - J CP30064, CP30104, CP3204F, CP3504 E1 - J - E2 J J - E3 - - - This information comes from an "installation guide" from ACA Pacific Pty Ltd (who are the Australian distributors for Conner hard drives). === File ends