Please note that the information in this file is written in two languages. Refer to Section A for English version and Section B for German version. Section A : ********************************************************************* * Additional Information * * * * AZT IDE CD-ROM Drive Installation Disk ver 2.30 * ********************************************************************* This file contains additional information about the CD-ROM drive installation software that was not available at printing time. General Information =================== Standard IDE supports up to a maximum of two IDE interfaces. Each IDE interface can support up to a maximum of two devices, i.e. either 2 hard disks, 2 CD-ROM drives or a combination of 1 hard disk & 1 CD-ROM drive. The port address for Primary & Secondary IDE interface is at 1F0H & 170H respectively. Primary IDE interface refers to the interface (at 1F0H) on your system where the IDE hard disk is connected (it can be built-in on the system motherboard or on a separate I/O card). Secondary IDE interface (at 170H) refers to the IDE interface on a separate interface card (e.g. the interface card bundled with this CD-ROM drive, on-board Secondary IDE interface or the interface on the sound card). CD-ROM Drive Configuration ========================== Please note that the IDE CD-ROM drive is factory configured to Single/Slave drive setting. Therefore, the following points are to be observed during the installation of the CD-ROM drive : 1.) If you are connecting the CD-ROM drive directly to the provided interface card or your system's on-board Secondary IDE interface, no jumper setting is required on either the CD-ROM or hard disk drive. If the on-board Secondary IDE interface has a hard disk connected, ensure that it is configured to Master drive setting. Please refer to your hard disk reference manual for more information. 2.) If your Sound Card has an IDE interface, please install the CD-ROM drive through the interface on the sound card. Please ensure that the jumper setting on the sound card is properly configured to IDE CD-ROM interface. For more information, refer to your sound card user's manual. 3.) If you are connecting the CD-ROM drive and the hard disk together through the on-board Primary IDE interface, a.) Please ensure that your hard disk is configured to Master drive setting. For more information, please refer to your hard disk reference manual. b.) Please also make sure that the following statement is in the [386Enh] section in the SYSTEM.INI file under WINDOWS directory. [386Enh] 32bitdiskaccess=OFF 4.) If you are connecting two CD-ROM drives directly to the provided interface card or your system's on-board Secondary IDE interface, ensure that one CD-ROM drive is configured to Master drive and the other to Slave drive setting. Please refer to the CD-ROM drive manual for more information on how to configure the drives. Section B : ************************************************************************* * Zustzliche Informationen * * * * AZT IDE CD-ROM Laufwerk Ver 2.30 * ************************************************************************* In dieser Datei finden Sie zustzliche Informationen zur CD-ROM Laufwerk Installationssoftware, die bei Drucklegung nicht verfgbar war. Allgemeine Informationen ======================== Standard IDE untersttzt maximal zwei IDE Schnittstellen. An jeder IDE Schnittstelle knnen maximal zwei Gerte angeschlossen sein, z.B. zwei Festplattem zwei CD-ROM Laufwerke oder eine Kombination aus einer Festplatte und einem CD-ROM Laufwerk. Die Portadresse fr ein primres IDE Interface ist 1F0H und fr ein sekundres IDE Interface 170H. Das primre IDE Interface ist der Anschlu (bei Adresse 1F0H), an dem Ihre Festplatte(n) angeschlossen ist. Es kann auf dem Mainboard oder auf einer Controllerkarte eingebaut sein. Ein sekundres IDE Interface (bei Adresse 170H) ist dann in Ihrem System vorhanden, wenn Sie in Ihrem System vier AT-Bus Festplatten installieren knnen. Sie finden es dann ebenfalls auf dem Mainboard oder auf der Controllerkarte. Ein zustzliches sekundres IDE Interface kann auch das auf bestimmten Soundkarten (z.B. Aztech WaveRider 32+) eingebaute sekundre IDE Interface oder das auf der optionalen Schnittstellenkarte zum IDE CD-ROM Laufwerk enthaltene Interface sein. CD-ROM Laufwerk Konfiguration ============================= Beachten Sie bitte, da das IDE CD-ROM Laufwerk ab Werk als Single/Slave Laufwerk konfiguriert ist. Bei der Installation dieses Laufwerks mssen folgende Punkte beachtet werden: 1.) Wenn Sie das CD-ROM Laufwerk direkt an der optionalen Interfacekarte von Aztech oder an einem anderen sekundren Interface in Ihrem PC anschlieen, so brauchen keine Jumper verndert zu werden. Wenn am sekundren IDE Interface in Ihrem System bereits eine Festplatte installiert ist, mu diese als Master konfiguriert sein. Die korrekte Jumpereinstellung entnehmen Sie bitte der Anleitung Ihrer Festplatte. 2.) Wenn an Ihrer Soundkarte ein IDE Interface vorhanden ist, schlieen Sie das CD-ROM Laufwerk bitte dort an. Stellen Sie sicher, da mit dem Jumper auf der Soundkarte die IDE Schnittstelle eingeschaltet ist. Weitere Hinweise finden Sie im Soundkartenhandbuch. 3.) Wenn Sie das CD-ROM Laufwerk zusammen mit einer Festplatte an einem primren IDE Interface in Ihrem System anschlieen wollen, dann beachten Sie folgende zwei Punkte: a) Stellen Sie sicher, da die (einzige) Festplatte als Master konfiguriert ist. Die korrekte Jumpereinstellung entnehmen Sie bitte der Anleitung Ihrer Festplatte. b) Stellen Sie auch sicher, da die folgende Zeile im Abschnitt [386Enh] der SYSTEM.INI Datei im WINDOWS Verzeichnis steht: [386Enh] 32BitDiskAccess=OFF 4.) Wenn Sie zwei IDE CD-ROM Laufwerke an einem vorhandenen sekundren IDE Interface in Ihrem System anschlieen wollen, so mu das eine CD-ROM Laufwerk als Master umkonfiguriert werden, whrend das andere weiter als Slave konfiguriert bleibt. Informationen zu diesem Thema finden Sie in Ihrem CD-ROM Handbuch. In diesem Fall kopieren Sie die Zeile DEVICE=(Pfad)SGIDECD.SYS... in der Datei CONFIG.SYS und editieren die zweite Zeile, so da die Namen der Laufwerke unterschiedlich sind. Die Zeilen knnen dann z.B. so aussehen: (Config.sys) DEVICE=C:\WR32\DRIVERS\SGIDECD.SYS /D:MSCD001 DEVICE=C:\WR32\DRIVERS\SGIDECD.SYS /D:MSCD002 Editieren Sie dann die Zeile mit dem Aufruf von MSCDEX.EXE in der Startdatei AUTOEXEC.BAT folgendermaen: (Autoexec.bat) C:\DOS\MSCDEX.EXE /D:MSCD001 /D:MSCD002 Hier reicht also eine Zeile, in der beide Namen genannt werden. Der Pfad C:\DOS ist hier nur ein Beispiel und kann in Ihrer Autoexec.bat Datei anders lauten. Auch knnen weitere Parameter folgen. Lassen Sie diese, wie sie sind, fgen Sie lediglich /D:MSCD002 zustzlich ein. --- Ende der Datei ---