Page 1 of 1

HELP!!! WHAT ARE THESE TO????

PostPosted: 20 Dec 2011 15:49
by cv70chall
OK, So I'm getting down to where I have maybe 1-2 cans of bolts, screws, nuts and so forth. I've come across these few that I have no clue where they belong. I think- the nuts and studs are for the tail light housings- as there are some missing, but I want to make sure these weren't used somewhere else in the car. HELP.
Also, can anyone provide a diagram of the top AC lines and where the metal bracket goes that would hold these down? (I don't have a photo of it, but it's metal and looks like it holds down (2) lines and secures with one screw. (I somehow remember this being on the fender- maybe the passenger side?)
HELP.

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 20 Dec 2011 19:29
by MLMFLCN
I think that the screws mount the front clip to the fenders.

The second item looks like the hardness that bolts to the master cylinder and holds the wiring harness.

Hope that helps.

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 20 Dec 2011 20:28
by cv70chall
And what about the bracket? Could it possibly be from inside?

Thanks

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 20 Dec 2011 20:57
by MLMFLCN
I think that the bracket mounts above the master cylinder and holds the wiring harness coming from the bulkhead to the battery/starter relay area. Trying to find a photo...

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 20 Dec 2011 21:27
by christer
cv70chall wrote:I think- the nuts and studs are for the tail light housings- as there are some missing,


Ithink so too.

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 1:43
by Alaskan_TA
Taillights, the clip may be for the tail light wiring, I have not seen one off the car in quite a while.

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 3:33
by Jon
Yes, the studs and captured washer/nuts are for the taillight housing. 12 in total I think. As for the clip would it be inside the rocker panel wireway?

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 5:42
by Pat
I totaly agree whit Jon, The studs and captured washer/nuts are for the taillight housing and the wire bracket is located on the firewall´s reinforcmetplate for the masterbrake cylinder/booster upper corners if im not mistaking =) and it looks like the braket whas for car whitout booster !

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 12:58
by cv70chall
Thanks. I figured the studs/ nuts were to the tail lights but wanted to be sure.
Regarding the bracket, can you supply a photo showing it's exact location?

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 19:02
by Pat
Here is a pic of the brackets on a drumbrake car that i asume you brackets are for and you can also see the location of the wire lome (Plastic wire clip) i driscribed for you under the wiper motor on the firewall.

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 20:50
by cv70chall
Thanks! I can clearly see where that wire clip goes.
As for the brackets, they are only for the manual brake setup? I have updated this to power and added a booster, so maybe I no longer use them, right?

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 21 Dec 2011 21:13
by Pat
If you have updated to power brake then you need another bracket and it is only one like in this picture !

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 22 Dec 2011 2:46
by Jon
Don't mean to overstep your topic cv , After looking at an old photo of my engine compartment, I spy that bracket over the booster. Don't know when I chucked it (or why :roll: ) but could use another. Any sources available?

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 22 Dec 2011 7:32
by Pat
Jon I dont know how good the repro are but the Mopar Shop that if im not mistaking is in CA have it !
scroll down on this page http://www.themoparshop.com/shop/index. ... 9ec855d977

Re: HELP!!! WHAT ARE THESE TO????

PostPosted: 22 Dec 2011 16:19
by Jon
Good price, thanks. :D